Experimental Study on Thermal-Hydraulic Performance of Single-Phase Water Flow in Narrow Rectangular Channel

2009 ◽  
Author(s):  
Mei Wang ◽  
Yan Wen ◽  
Suizheng Qiu ◽  
Guanghui Su ◽  
Weifeng Ni
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Friction Factor ◽  
Water Flow ◽  
Single Phase ◽  
Rectangular Channel ◽  
Flow Region ◽  
Phase Water

The purpose of this study is to discover the differences of pressure drop and heat transfer of single-phase water flow between conventional channels and narrow rectangular channels. Furthermore, the differences between the level and the vertical channel have been studied. The gap of the test channel is 1.8mm. Compared with conventional channels, the narrow rectangular channel showed differences in both flow and heat transfer characteristics. The critical Reynolds number of transition from laminar flow to turbulent flow is 900∼1300, which is smaller compared with conventional channels. The friction factor is larger than that of the conventional channels and the correlation of friction factor with Reynolds number was given by experimental results. From the relation graph of Nusselt number and Reynolds number, the demarcation of the laminar flow region and turbulence flow region is obvious. In laminar region, Nusselt number almost remained constant and approximately consistent with numerical simulation results. While in turbulent region, Nusselt number increased significantly with increasing Reynolds number. A new Nusselt number correlation was obtained based on Dittus-Boelter equation, and the coefficients were less about 13% than that of Dittus-Boelter equation.

Local Single-Phase Heat Transfer Research of Natural Circulation in Narrow Rectangular Channel

2017 ◽  
Author(s):  
Zhiqiang Zhu ◽  
Xiaxin Cao ◽  
Changqi Yan ◽  
Chunping Tian
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Inclination Angle ◽  
Local Nusselt Number ◽  
Single Phase ◽  
Natural Circulation ◽  
Rectangular Channel ◽  
Inlet Temperature

In order to explore and analyze the heat transfer characteristics in narrow rectangular channel, experiments on local single-phase heat transfer of natural circulation in a one-side heating narrow rectangular channel have been conducted under vertical and inclined condition. The thermotechnical parameters such as inlet temperature, heat flux and inclination angle varies during the experiments. The width of the flow channel is 40 mm and the narrow gap is 2 mm. It is heated from one side with a homogeneous and constant heat flux and the working medium is deionized water. Based on the experimental results, under vertical condition, the driving force in the loop goes up and the Reynolds number also increases when the inlet temperature is elevated, which causes an increase in local Nusselt number. When the heat flux rises, the local Nusselt number increases and the heat transfer temperature difference increases. The local Nusselts number is influenced by entrance effect and the entrance region length is computed for laminar and turbulent flow. Under inclined condition, with the inclination angle from −30° to 30°, it is found that when the inclination angle is positive, the local Nusselt number in fully developed region is larger than that under vertical condition and increases with the angle value, even though the Reynolds number decreases by the effect of incline. This phenomenon is explained by giving an analysis of the natural convection, which is characterized by the normal Grashof number, in the direction perpendicular to the heating plat. Moreover, the variation of heat transfer is also interpreted on the basis of field coordination principle. However, when the inclination angle is negative, the heat transfer shows no obvious difference between vertical condition and inclined condition.

Heat Transfer in Thin, Compact Heat Exchangers With Circular, Rectangular, or Pin-Fin Flow Passages

1992 ◽  
Vol 114 (2) ◽  
pp. 373-382 ◽  
Author(s):  
D. A. Olson
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Rectangular Channel ◽  
Fluid Temperature ◽  
Compact Heat Exchangers ◽  
Pin Fin

We have measured heat transfer and pressure drop of three thin, compact heat exchangers in helium gas at 3.5 MPa and higher, with Reynolds numbers of 450 to 36,000. The flow geometries for the three heat exchanger specimens were: circular tube, rectangular channel, and staggered pin fin with tapered pins. The specimens were heated radiatively at heat fluxes up to 77 W/cm2. Correlations were developed for the isothermal friction factor as a function of Reynolds number, and for the Nusselt number as a function of Reynolds number and the ratio of wall temperature to fluid temperature. The specimen with the pin fin internal geometry had significantly better heat transfer than the other specimens, but it also had higher pressure drop. For certain conditions of helium flow and heating, the temperature more than doubled from the inlet to the outlet of the specimens, producing large changes in gas velocity, density, viscosity, and thermal conductivity. These changes in properties did not affect the correlations for friction factor and Nusselt number in turbulent flow.

scholarly journals Efek vortex generators terhadap peningkatan perpindahan panas pada aliran melewati heated tubes

2020 ◽  
Vol 9 (2) ◽  
Author(s):  
Yafid Effendi ◽  
Ali Rosyidin
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Friction Factor ◽  
Rectangular Channel ◽  
Evaluation Criteria ◽  
Vortex Generators ◽  
High Thermal Resistance ◽  
Flow Pressure ◽  
Delta Winglet

In this decade, improving the rate of heat transfer has become a big challenge. The high thermal resistance of the gas side of the heat exchanger has an impact on the low rate of heat transfer. Therefore, an experimental study was carried out aimed at looking at conditions of hot temperature and decreased air flow pressure through a heated tube in a rectangular channel using artificial surfaces, namely the concave delta winglet and delta winglet vortex generators. Concave delta winglet vortex generators (CDW VGs) are installed in-line and staggered with one, and two pairs are arranged in common-flow-down (CFD) in the direction of flow with an angle of attack of 15o. The experimental results show that the best thermal performance is observed in the use of two rows CDW VGs staggered, where the value of performance evaluation criteria (PEC) is 28.88% higher than the use of CDW VGs in-line, DW VGs staggered and DW VGs in-line at the same Reynolds number. At the same Reynolds number, the Nusselt number ratio and the friction factor ratio increased 45.25% and 152.05% respectively, occurring in two rows of CDW VGs staggered compared to other vortex generators.Keywords: vortex generators, heat transfer, Nusselt number, friction factor, PEC

Heat transfer enhancement using second mode self-oscillating structures

2019 ◽  
Vol 30 (7) ◽  
pp. 3827-3842
Author(s):  
Samer Ali ◽  
Zein Alabidin Shami ◽  
Ali Badran ◽  
Charbel Habchi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Flow Regime ◽  
Vortex Generator ◽  
Reynolds Numbers ◽  
Content Type ◽  
Laminar Flow Regime ◽  
Second Mode

Purpose In this paper, self-sustained second mode oscillations of flexible vortex generator (FVG) are produced to enhance the heat transfer in two-dimensional laminar flow regime. The purpose of this study is to determine the critical Reynolds number at which FVG becomes more efficient than rigid vortex generators (RVGs). Design/methodology/approach Ten cases were studied with different Reynolds numbers varying from 200 to 2,000. The Nusselt number and friction coefficients of the FVG cases are compared to those of RVG and empty channel at the same Reynolds numbers. Findings For Reynolds numbers higher than 800, the FVG oscillates in the second mode causing a significant increase in the velocity gradients generating unsteady coherent flow structures. The highest performance was obtained at the maximum Reynolds number for which the global Nusselt number is improved by 35.3 and 41.4 per cent with respect to empty channel and rigid configuration, respectively. Moreover, the thermal enhancement factor corresponding to FVG is 72 per cent higher than that of RVG. Practical implications The results obtained here can help in the design of novel multifunctional heat exchangers/reactors by using flexible tabs and inserts instead of rigid ones. Originality/value The originality of this paper is the use of second mode oscillations of FVG to enhance heat transfer in laminar flow regime.

Heat Transfer And Pressure Drop Of An Angled Discrete Turbulator At Elevated Reynolds Numbers Up To 900,000

2021 ◽  
pp. 1-29
Author(s):  
Sam Ghazi-Hesami ◽  
Dylan Wise ◽  
Keith Taylor ◽  
Peter Ireland ◽  
Étienne Robert
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Enhance Heat Transfer ◽  
Near Surface ◽  
Number Range ◽  
Smooth Channel

Abstract Turbulators are a promising avenue to enhance heat transfer in a wide variety of applications. An experimental and numerical investigation of heat transfer and pressure drop of a broken V (chevron) turbulator is presented at Reynolds numbers ranging from approximately 300,000 to 900,000 in a rectangular channel with an aspect ratio (width/height) of 1.29. The rib height is 3% of the channel hydraulic diameter while the rib spacing to rib height ratio is fixed at 10. Heat transfer measurements are performed on the flat surface between ribs using transient liquid crystal thermography. The experimental results reveal a significant increase of the heat transfer and friction factor of the ribbed surface compared to a smooth channel. Both parameters increase with Reynolds number, with a heat transfer enhancement ratio of up to 2.15 (relative to a smooth channel) and a friction factor ratio of up to 6.32 over the investigated Reynolds number range. Complementary CFD RANS (Reynolds-Averaged Navier-Stokes) simulations are performed with the κ-ω SST turbulence model in ANSYS Fluent® 17.1, and the numerical estimates are compared against the experimental data. The results reveal that the discrepancy between the experimentally measured area averaged Nusselt number and the numerical estimates increases from approximately 3% to 13% with increasing Reynolds number from 339,000 to 917,000. The numerical estimates indicate turbulators enhance heat transfer by interrupting the boundary layer as well as increasing near surface turbulent kinetic energy and mixing.

Spatially Resolved Heat Transfer and Friction Factors in a Rectangular Channel With 45-Deg Angled Crossed-Rib Turbulators

2003 ◽  
Vol 125 (3) ◽  
pp. 575-584 ◽  
Author(s):  
P. M. Ligrani ◽  
G. I. Mahmood
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Rectangular Channel ◽  
Test Surface ◽  
Spatially Resolved ◽  
Nusselt Numbers ◽  
Friction Factors ◽  
Smooth Channel ◽  
Rib Turbulators

Spatially resolved Nusselt numbers, spatially averaged Nusselt numbers, and friction factors are presented for a stationary channel with an aspect ratio of 4 and angled rib turbulators inclined at 45 deg with perpendicular orientations on two opposite surfaces. Results are given at different Reynolds numbers based on channel height from 10,000 to 83,700. The ratio of rib height to hydraulic diameter is .078, the rib pitch-to-height ratio is 10, and the blockage provided by the ribs is 25% of the channel cross-sectional area. Nusselt numbers are given both with and without three-dimensional conduction considered within the acrylic test surface. In both cases, spatially resolved local Nusselt numbers are highest on tops of the rib turbulators, with lower magnitudes on flat surfaces between the ribs, where regions of flow separation and shear layer reattachment have pronounced influences on local surface heat transfer behavior. The augmented local and spatially averaged Nusselt number ratios (rib turbulator Nusselt numbers normalized by values measured in a smooth channel) vary locally on the rib tops as Reynolds number increases. Nusselt number ratios decrease on the flat regions away from the ribs, especially at locations just downstream of the ribs, as Reynolds number increases. When adjusted to account for conduction along and within the test surface, Nusselt number ratios show different quantitative variations (with location along the test surface), compared to variations when no conduction is included. Changes include: (i) decreased local Nusselt number ratios along the central part of each rib top surface as heat transfer from the sides of each rib becomes larger, and (ii) Nusselt number ratio decreases near corners, where each rib joins the flat part of the test surface, especially on the downstream side of each rib. With no conduction along and within the test surface (and variable heat flux assumed into the air stream), globally-averaged Nusselt number ratios vary from 2.92 to 1.64 as Reynolds number increases from 10,000 to 83,700. Corresponding thermal performance parameters also decrease as Reynolds number increases over this range, with values in approximate agreement with data measured by other investigators in a square channel also with 45 deg oriented ribs.

scholarly journals The Effect of Nanofluid Volume Concentration on Heat Transfer and Friction Factor inside a Horizontal Tube

2013 ◽  
Vol 2013 ◽  
pp. 1-12 ◽  
Author(s):  
Adnan M. Hussein ◽  
K. V. Sharma ◽  
R. A. Bakar ◽  
K. Kadirgama
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Thermal Properties ◽  
Friction Factor ◽  
Volume Concentration ◽  
Convection Heat Transfer ◽  
Horizontal Tube ◽  
Maximum Deviation ◽  
Flat Tube

The additives of solid nanoparticles to liquids are significant enhancement of heat transfer and hydrodynamic flow. In this study, the thermal properties of three types of nanoparticles (Al2O3, TiO2, and SiO2) dispersed in water as a base fluid were measured experimentally. Forced convection heat transfer turbulent flow inside heated flat tube was numerically simulated. The heat flux around flat tube is 5000 W/m2and Reynolds number is in the range of5×103to50×103. CFD model by finite volume method used commercial software to find hydrodynamic and heat transfer coefficient. Simulation study concluded that the thermal properties measured and Reynolds number as input and friction factor and Nusselt number as output parameters. Data measured showed that thermal conductivity and viscosity increase with increasing the volume concentration of nanofluids with maximum deviation 19% and 6%, respectively. Simulation results concluded that the friction factor and Nusselt number increase with increasing the volume concentration. On the other hand, the flat tube enhances heat transfer and decreases pressure drop by 6% and −4%, respectively, as compared with circular tube. Comparison of numerical analysis with experimental data available showed good agreement with deviation not more than 2%.

A Comparative Study of Performance of Low Reynolds Number Turbulence Models for Various Heat Transfer Enhancement Simulations

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Ankit Tiwari ◽  
Savas Yavuzkurt
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Enhancement ◽  
Friction Factor ◽  
Fluid Dynamic ◽  
Low Reynolds Number ◽  
Turbulence Models ◽  
Transfer Enhancement ◽  
Low Reynolds

The goal of this study is to evaluate the computational fluid dynamic (CFD) predictions of friction factor and Nusselt number from six different low Reynolds number k–ε (LRKE) models namely Chang–Hsieh–Chen (CHC), Launder–Sharma (LS), Abid, Lam–Bremhorst (LB), Yang–Shih (YS), and Abe–Kondoh–Nagano (AKN) for various heat transfer enhancement applications. Standard and realizable k–ε (RKE) models with enhanced wall treatment (EWT) were also studied. CFD predictions of Nusselt number, Stanton number, and friction factor were compared with experimental data from literature. Various parameters such as effect of type of mesh element and grid resolution were also studied. It is recommended that a model, which predicts reasonably accurate values for both friction factor and Nusselt number, should be chosen over disparate models, which may predict either of these quantities more accurately. This is based on the performance evaluation criterion developed by Webb and Kim (2006, Principles of Enhanced Heat Transfer, 2nd ed., Taylor and Francis Group, pp. 1–72) for heat transfer enhancement. It was found that all LRKE models failed to predict friction factor and Nusselt number accurately (within 30%) for transverse rectangular ribs, whereas standard and RKE with EWT predicted friction factor and Nusselt number within 25%. Conversely, for transverse grooves, AKN, AKN/CHC, and LS (with modified constants) models accurately predicted (within 30%) both friction factor and Nusselt number for rectangular, circular, and trapezoidal grooves, respectively. In these cases, standard and RKE predictions were inaccurate and inconsistent. For longitudinal fins, Standard/RKE model, AKN, LS and Abid LRKE models gave the friction factor and Nusselt number predictions within 25%, with the AKN model being the most accurate.

scholarly journals Experimental Study on Liquid Flow and Heat Transfer in Rough Microchannels

2019 ◽  
Vol 2019 ◽  
pp. 1-9
Author(s):  
Xuan Zhang ◽  
Taocheng Zhao ◽  
Suchen Wu ◽  
Feng Yao
Keyword(s):  
Heat Transfer ◽  
Surface Roughness ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Cross Section ◽  
Liquid Flow ◽  
Flow And Heat Transfer ◽  
Section Shape ◽  
Poiseuille Number

Although roughness is negligible for laminar flow through tubes in classic fluid mechanics, the surface roughness may play an important role in microscale fluid flow due to the large ratio of surface area to volume. To further verify the influence of rough surfaces on microscale liquid flow and heat transfer, a performance test system of heat transfer and liquid flow was designed and built, and a series of experimental examinations are conducted, in which the microchannel material is stainless steel and the working medium is methanol. The results indicate that the surface roughness plays a significant role in the process of laminar flow and heat transfer in microchannels. In microchannels with roughness characteristics, the Poiseuille number of liquid laminar flow relies not only on the cross section shape of the rough microchannels but also on the Reynolds number of liquid flow. The Poiseuille number of liquid laminar flow in rough microchannels increases with increasing Reynolds number. In addition, the Nusselt number of liquid laminar heat transfer is related not only to the cross section shape of a rough microchannel but also to the Reynolds number of liquid flow, and the Nusselt number increases with increasing Reynolds number.

Numerical Simulation of Nonlinear Flow and Heat Transfer in a Sudden Expansion and Contraction Channel

2016 ◽  
Author(s):  
M. Yang ◽  
L. Q. Yang ◽  
W. Lu ◽  
L. Li ◽  
Q. X. Liu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Reynolds Number ◽  
Rectangular Channel ◽  
Flow Region ◽  
Nonlinear Flow ◽  
Forced Flow ◽  
Sudden Expansion ◽  
Symmetric State ◽  
Flow And Heat Transfer

Numerical simulation of forced flow in sudden-expansion followed by sudden-contraction rectangular channel was presented for the whole flow region. The nonlinear flow and heat transfer characteristics were investigated by various Reynolds number and geometrical dimension and the critical Reynolds numbers under different conditions have been calculated. The results show flow and heat transfer from symmetric state to asymmetric state with the increase of Re. When Re<Rec (critical Reynolds number for flow transformation), the symmetric state is stable. On the other hand, when Re ≥Rec, the flow loses stability and from symmetric to asymmetric via a symmetry-breaking bifurcation. And the heat transfer performance have relevant characteristics as fluid flow.

Sign in / Sign up

Export Citation Format

Share Document