Architecting “Maintenance Program” for Piping and Pipe Support

Author(s):  
Koichi Tsumori ◽  
Yoshizumi Fukuhara ◽  
Hiroyuki Terunuma ◽  
Koji Yamamoto ◽  
Satoshi Momiyama

A new inspection standard that enhanced quality of operating /maintenance management of the nuclear power plant was introduced in 2009. After the Fukushima Daiichi nuclear disaster (Mar. 11th 2011), the situation surrounding the nuclear industry has dramatically changed, and the requirement for maintenance management of nuclear power plants is pushed for more stringent nuclear safety regulations. The new inspection standard requires enhancing equipment maintenance. It is necessary to enhance maintenance of not only equipment but also piping and pipe support. In this paper, we built the methodology for enhancing maintenance plan by rationalizing and visualizing of piping and pipe support based on the “Maintenance Program” in cooperating with 3D-CAD system.

Author(s):  
Dae-Yul Jung ◽  
Yoon-Kee Kang ◽  
Chang-Hyung You

This paper covers advanced construction technologies that are generally used for nuclear power plants and presents advanced construction methods that can contribute to an efficient and short construction schedule. The construction schedule is driven by the activities of the critical path. The advanced construction methods consist of Modularization, Improvement of Mechanical Rebar splices, Application of 3D-CAD system for information and control, and the installation of RVI and RCL at the same time. Some methods have been applied in actual Nuclear power projects and others have been developing under the research and development program. It incorporates the experiences and insights from recent nuclear construction projects all over the world.


Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3832
Author(s):  
Awwal Mohammed Arigi ◽  
Gayoung Park ◽  
Jonghyun Kim

Advancements in the nuclear industry have led to the development of fully digitized main control rooms (MCRs)—often termed advanced MCRs—for newly built nuclear power plants (NPPs). Diagnosis is a major part of the cognitive activity in NPP MCRs. Advanced MCRs are expected to improve the working environment and reduce human error, especially during the diagnosis of unexpected scenarios. However, with the introduction of new types of tasks and errors by digital MCRs, a new method to analyze the diagnosis errors in these new types of MCRs is required. Task analysis for operator diagnosis in an advanced MCR based on emergency operation was performed to determine the error modes. The cause-based decision tree (CBDT) method—originally developed for analog control rooms—was then revised to a modified CBDT (MCBDT) based on the error mode categorizations. This work examines the possible adoption of the MCBDT method for the evaluation of diagnosis errors in advanced MCRs. We have also provided examples of the application of the proposed method to some common human failure events in emergency operations. The results show that with some modifications of the CBDT method, the human reliability in advanced MCRs can be reasonably estimated.


Author(s):  
Ronald C. Lippy

The nuclear industry is preparing for the licensing and construction of new nuclear power plants in the United States. Several new designs have been developed and approved, including the “traditional” reactor designs, the passive safe shutdown designs and the small modular reactors (SMRs). The American Society of Mechanical Engineers (ASME) provides specific Codes used to perform preservice inspection/testing and inservice inspection/testing for many of the components used in the new reactor designs. The U.S. Nuclear Regulatory Commission (NRC) reviews information provided by applicants related to inservice testing (IST) programs for Design Certifications and Combined Licenses (COLs) under Part 52, “Licenses, Certifications, and Approvals for Nuclear Power Plants,” in Title 10 of the Code of Federal Regulations (10 CFR Part 52) (Reference 1). The 2012 Edition of the ASME OM Code defines a post-2000 plant as a nuclear power plant that was issued (or will be issued) its construction permit, or combined license for construction and operation, by the applicable regulatory authority on or following January 1, 2000. The New Reactors OM Code (NROMC) Task Group (TG) of the ASME Code for Operation and Maintenance of Nuclear Power Plants (NROMC TG) is assigned the task of ensuring that the preservice testing (PST) and IST provisions in the ASME OM Code to address pumps, valves, and dynamic restraints (snubbers) in post-2000 nuclear power plants are adequate to provide reasonable assurance that the components will operate as needed when called upon. Currently, the NROMC TG is preparing proposed guidance for the treatment of active pumps, valves, and dynamic restraints with high safety significance in non-safety systems in passive post-2000 reactors including SMRs.


2012 ◽  
Vol 253-255 ◽  
pp. 303-307 ◽  
Author(s):  
Jing Yang ◽  
Zhen Fu Chen ◽  
Yuan Chu Gan ◽  
Qiu Wang Tao

Radiation shielding concrete is widely used in nuclear power plants, accelerators, hospitals, etc. With the development of nuclear industry technology, research on radiation shielding material properties is of great importance. Research on properties of radiation shielding concrete with different aggregates or admixtures and the effect of high temperature on the performance of shielding concrete are introduced. Along with the nuclear waste increase, shielding concrete durability and nuclear waste disposal are getting paramount.


2018 ◽  
Vol 184 (1) ◽  
pp. 98-108
Author(s):  
Sang-Tae Kim ◽  
Jaeryong Yoo

Abstract In this study, the radiation exposure of workers at workplaces registered and licensed between 2008 and 2017 for the production/sale/use of radioactive isotopes (RI) and radioactive generators (RG) was analysed to evaluate the quality of radiation safety management controls in use. The number of facilities using RIs increased by ~26% from 2008 to 2017 whereas the number of facilities using RGs increased by ~166% over the same period. There were 33 029 radiation workers in all fields in 2008, and the number increased by ~32% to 43 467 by 2017. However, the collective effective dose of radiation received by workers decreased in all industries except for those working in nuclear power plants. In other words, the quality of radiation safety management improved over that same time period due to the systematic, continuous introduction of safety mechanisms by the regulatory authority.


Author(s):  
S. Kalyanam ◽  
D.-J. Shim ◽  
P. Krishnaswamy ◽  
Y. Hioe

HDPE pipes are considered by the nuclear industry as a potential replacement option to currently employed metallic piping for service-water applications. The pipes operate under high temperatures and pressures. Hence HDPE pipes are being evaluated from perspective of design, operation, and service life requirements before routine installation in nuclear power plants. Various articles of the ASME Code Case N-755 consider the different aspects related to material performance, design, fabrication, and examination of HDPE materials. Amongst them, the material resistance (part of Article 2000) to the slow crack growth (SCG) from flaws/cracks present in HDPE pipe materials is an important concern. Experimental investigations have revealed that there is a marked difference (almost three orders less) in the time to failure when the notch/flaw is in the butt-fusion joint, as opposed to when the notch/flaw is located in the parent HDPE material. As part of ongoing studies, the material resistance to SCG was investigated earlier for unimodal materials. The current study investigated the SCG in parent and butt-fusion joint materials of bimodal HDPE (PE4710) pipe materials acquired from two different manufacturers. The various stages of the specimen deformation and failure during the creep test are characterized. Detailed photographs of the specimen side-surface were used to monitor the specimen damage accumulation and SCG. The SCG was tested using a large specimen (large creep frame) as well as using a smaller size specimen (PENT frame) and the results were compared. Further, the effect of polymer orientation or microstructure in the bimodal HDPE pipe on the SCG was studied using specimens with axial and circumferential notch orientations in the parent pipe material.


2021 ◽  
Vol 331 ◽  
pp. 04003
Author(s):  
Dewi Prima Meiliasari ◽  
Berton Suar Panjaitan ◽  
Toto Heryanto ◽  
Wilopo

The application of nuclear power plants in the world is increasing and has the potential for accidents, including nuclear weapons tests from outside the Nuclear Non-Proliferation Treaty, thus allowing radioactive releases to fall into Indonesian territory, which is a potential threat. Indonesia also utilizes nuclear power in many fields, thus also potentially becoming a national threat. To prevent the threat of radiation potential requires a nuclear disaster Early Warning System (EWS) that can be accessed by the community. This research analysed the EWS that Indonesia needed, using qualitative methods by describing the results of research obtained from interviews and secondary data. Results and research discussions starting from observation and monitoring of radiation exposure, warning services, information dissemination, and supported by countermeasures for the effectiveness of the EWS. The results showed that the development of an integrated nuclear disaster EWS that is easily accessible to the community quickly and continuously under the development of an emergency is a strategy as a decision to reduce the risk of nuclear disaster. The development of the strategy requires a legal basis that regulates coordination between ministries/institutions, from planning to information dissemination to ensure the safety of the public and Indonesian people's security.


Author(s):  
William D. Rezak

One of America’s best kept secrets is the success of its nuclear electric power industry. This paper presents data which support the construction and operating successes enjoyed by energy companies that operate nuclear power plants in the US. The result—the US nuclear industry is alive and well. Perhaps it’s time to start anew the building of nuclear power plants. Let’s take the wraps off the major successes achieved in the nuclear power industry. Over 20% of the electricity generated in the United States comes from nuclear power plants. An adequate, reliable supply of reasonably priced electric energy is not a consequence of an expanding economy and gross national product; it is an absolute necessity before such expansion can occur. It is hard to imagine any aspect of our business or personal lives not, in some way, dependent upon electricity. All over the world (in 34 countries) nuclear power is a low-cost, secure, safe, dependable, and environmentally friendly form of electric power generation. Nuclear plants in these countries are built in six to eight years using technology developed in the US, with good performance and safety records. This treatise addresses the success experienced by the US nuclear industry over the last 40 years, and makes the case that this reliable, cost-competitive source of electric power can help support the economic engine of the country and help prevent experiences like the recent crisis in California. Traditionally, the evaluation of electric power generation facility performance has focused on the ability of plants to produce at design capacity for high percentages of the time. Successful operation of nuclear facilities is determined by examining capacity or load factors. Load factor is the percentage of design generating capacity that a power plant actually produces over the course of a year’s operation. This paper makes the case that these operating performance indicators warrant renewed consideration of the nuclear option. Usage of electricity in the US now approaches total generating capacity. The Nuclear Regulatory Commission has pre-approved construction and operating licenses for several nuclear plant designs. State public service commissions are beginning to understand that dramatic reform is required. The economy is recovering and inflation is minimal. It’s time, once more, to turn to the safe, reliable, environmentally friendly nuclear power alternative.


Author(s):  
Abhinav Gupta ◽  
Ankit Dubey ◽  
Sunggook Cho

Abstract Nuclear industry spends enormous time and resources on designing and managing piping nozzles in a plant. Nozzle locations are considered as a potential location for possible failure that can lead to loss of coolant accident. Industry spends enormous time in condition monitoring and margin management at nozzle locations. Margins against seismic loads play a significant role in the overall margin management. Available margins against thermal loads are highly dependent upon seismic margins. In recent years, significant international collaboration has been undertaken to study the seismic margin in piping systems and nozzles through experimental and analytical studies. It has been observed that piping nozzles are highly overdesigned and the margins against seismic loads are quite high. While this brings a perspective of sufficient safety, such excessively high margins compete with available margins against thermal loads particularly during the life extension and subsequent license renewal studies being conducted by many plants around the world. This paper focuses on identifying and illustrating two key reasons that lead to excessively conservative estimates of nozzle fragilities. First, it compares fragilities based on conventional seismic analysis that ignores piping-equipment-structure interaction on nozzle fragility with the corresponding assessment by considering such interactions. Then, it presents a case that the uncertainties considered in various parameters for calculating nozzle fragility are excessively high. The paper identifies a need to study the various uncertainties in order to achieve a more realistic quantification based on recent developments in our understanding of the seismic behavior of piping systems.


Sign in / Sign up

Export Citation Format

Share Document