A Validation of RELAP on Predicting Nuclear Power Plant Phenomena

2018 ◽  
Author(s):  
Ji Soo Ahn ◽  
Michael Bluck ◽  
Matthew Eaton ◽  
Chris Jackson
Keyword(s):  
Thermal Stratification ◽  
Nuclear Power ◽  
Power Plants ◽  
Feed Water ◽  
Multiple Channels ◽  
Horizontal Pipe ◽  
One Dimensional ◽  
Piping Systems ◽  
Surge Line ◽  
Input Model

In this study, RELAP5’s capability to simulate thermal stratification under different conditions is assessed. In nuclear power plants (NPPs), thermal stratification can occur in the following locations: pressurizer, piping systems such as hot legs, cold legs, surge lines, and cooling tanks if available. In general, thermal stratification in a horizontal pipe could not be simulated by RELAP5 due to the inherent one-dimensional setting. Moreover, RELAP5 failed to simulate turbulent penetration which was often a pre-requisite prior to thermal stratification in a pipe. This type of situation could arise in connection between hot leg and surge line, spray lines, feed water lines, etc. It is recommended that for this type of problem CFD be used. In the literature, it was found that RELAP5 was capable of simulating thermal stratification in a pool or a tank-like component if multiple channels and crossflow junctions were used. However, due to uncertainties associated with the input model, the current RELAP5 model failed to reproduce experimental data and therefore further investigation would be required to identify the sources of error.

Experimental Investigation on Flash Evaporation Related to Pipe Leakage

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Benan Cai ◽  
Qi Zhang ◽  
Yu Weng ◽  
Hongfang Gu ◽  
Haijun Wang
Keyword(s):  
High Temperature ◽  
Thermal Fatigue ◽  
Weber Number ◽  
Thermal Stratification ◽  
Nuclear Power ◽  
Power Plants ◽  
Response Speed ◽  
Flash Evaporation ◽  
Main Pipe ◽  
Surge Line

Abstract Pipelines such as the surge line and main pipe are easily subjected to thermal stratification and thermal fatigue as a result of the nonuniform temperature distribution in the nuclear power plants. When the surge line or main pipe subjected to thermal stratification and thermal fatigue keeps operating for long time, the pipe leakage may happen due to the existence of pipeline crack. When the fluids with high temperature and pressure leak in the crack, the water will evaporate quickly, which means this process belongs to spray flash evaporation process. The flash evaporation related to pipe leak was experimentally studied in the paper. The experiment was carried out under high temperature and high pressure with low spray rate. The temperature and relative humidity (T&H) variations over time were monitored in the experiment with installing T&H detectors. The T&H variations at different measurement positions and with different spray rates were analyzed, respectively. In addition, the effect of the dimensionless parameters including the Weber number and Jakob number was also investigated. Results indicated that the response speed increased with the increase of the spray flow rate. Higher Weber number and higher Jakob number led to higher evaporation rate. The slight pipe leakage can be predicted by using the (T&H) in the hazardous areas.

A New Method to Weaken Thermal Stratification Phenomena in Pipes of Nuclear Power Plant

2013 ◽  
Author(s):  
Shengfei Wang ◽  
Yuxin Pang ◽  
Xiaojing Li ◽  
Dandan Fu ◽  
Yang Li ◽  
...  
Keyword(s):  
Thermal Stratification ◽  
Nuclear Power ◽  
Thermal Stresses ◽  
Heat Pipes ◽  
New Method ◽  
Simple Experiment ◽  
Pressurized Water ◽  
Piping Systems ◽  
Surge Line ◽  
Water Reactors

Thermal stratification phenomena are observed in piping systems of pressurized water reactors, especially in the pressurizer surge line. As a result of the thermal stratification induced thermal stresses, fatigue problems can occur in the pipework. US NRC requirements have also identified flow stratification in surge lines as a phenomenon that must be considered in the design basis of surge lines. In this paper, a new method to reduce thermal stratification is proposed. As we all know, heat pipe is a simple device with no moving parts and can transfer large quantities of heat over fairly large distance. The new method is that using heat pipes to weaken the thermal stratification. In order to validate the new method, a simple experiment and theoretical analysis was taken. The results show that, the temperature difference of thermal stratification with heat pipes is smaller than the stratification without heat pipes. A design scheme was also given at the end of paper.

Stress and Fatigue Analysis of Pressurizer Surge Line under Thermal Stratification

2019 ◽  
Vol 795 ◽  
pp. 268-275
Author(s):  
Peng Tang ◽  
Zhi Wei Liu ◽  
Hong Wei Qiao ◽  
Peng Zhou Li
Keyword(s):  
Temperature Distribution ◽  
Temperature Difference ◽  
Thermal Stratification ◽  
Nuclear Power ◽  
Power Plants ◽  
Load Condition ◽  
Maximum Temperature ◽  
Large Temperature ◽  
Maximum Temperature Difference ◽  
Surge Line

Pressurizer surge line is one of the key equipments of nuclear power plants. The thermal stratification due to the intersection of hot and cold fluids inside the pressurizer surge line may affect the safe operation of nuclear power plant. In order to investigate the stress distribution and fatigue characteristics of surge line subjected to long-term thermal stratified loadings, a mechanical model of the surge line was established. And then, according to different temperature distribution assumptions, thermal stress analysis and fatigue assessment were conducted. The results show that the maximum stress appears under the load condition with maximum temperature difference, and finer temperature distribution can obtain more accurate stress and displacement results. The maximum value of fatigue cumulative coefficient appears at the junction of straight pipe and elbow with large temperature difference.

Experimental Investigation on the Pipe Leakage

2017 ◽  
Author(s):  
Benan Cai ◽  
Qi Zhang ◽  
Yu Weng ◽  
Hongfang Gu ◽  
Haijun Wang
Keyword(s):  
High Temperature ◽  
Thermal Stratification ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Normal Operation ◽  
Pipe System ◽  
Humidity Change ◽  
Temperature And Humidity ◽  
Surge Line

Pipelines are widely used in many fields including power industry, petroleum system etc. Pipelines such as the surge line and main pipe are easily subjected to thermal stratification as a result of the non-uniform temperature distribution in the nuclear power plants. Furthermore, pipelines can suffer from thermal fatigue in virtue of long-term uneven stress distribution. When the surge line or main pipe subjected to thermal stratification and thermal fatigue keeps operating for long time, the pipe leakage may happen because of the existence of pipeline crack. The thermal pipeline crack leakage mainly appears in the region with stress concentration. As the pipe system is always covered with thermal insulation layer in the actual nuclear power plants, it is hard for workers to observe pipeline leak, which can have a bad effect on the normal operation. Since the temperature and humidity close to the pipe crack due to leakage can change compared to the normal operation, we can infer from the temperature and humidity changes that the pipe leakage occurs. Based on this idea, the temperature and humidity near the crack of the pipe need to be measured to detect the leakage fields. As the fluids with high pressure and high temperature flow in the pipe system in an actual nuclear power plant, the pipe leakage experiment was performed in the high pressure and high temperature condition. When the fluids with high temperature and pressure leak in the crack, the water will evaporate quickly, which means this process belongs to spray flash evaporation process. The temperature and humidity variations were monitored in the experiment with temperature and humidity probes which have the advantage of responding to the change of temperature and humidity sensitively. The data collection program was mainly written based on the LABVIEW platform. The collecting time step was set 1s. As the measuring position and leakage flux are two key factors for the pipe leakage, the experiment was carried out with different measuring positions and leakage fluxes conditions. The experimental results showed that the leak flux had an important influence on the temperature and humidity near the pipe crack. The temperature and humidity started to change in a very short time with large leak flux. At the same time, the velocity of the temperature and humidity change was high with large leak flux. When the pipe leakage occurred in the location near the temperature and humidity probe, the temperature and humidity responded quickly and the velocity of temperature and humidity change was large. The experiment data can be used for the prediction of the pipe leakage in the nuclear power plants.

Nuclear Power Plant Fires and Explosions: Part IV — Water Hammer Explosion Mechanisms

2017 ◽  
Author(s):  
Robert A. Leishear
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Water Hammer ◽  
Compression Process ◽  
Flammable Gas ◽  
Piping Systems ◽  
Fukushima Daiichi ◽  
Accident Conditions

Water hammers, or fluid transients, compress flammable gasses to their autognition temperatures in piping systems to cause fires or explosions. While this statement may be true for many industrial systems, the focus of this research are reactor coolant water systems (RCW) in nuclear power plants, which generate flammable gasses during normal operations and during accident conditions, such as loss of coolant accidents (LOCA’s) or reactor meltdowns. When combustion occurs, the gas will either burn (deflagrate) or explode, depending on the system geometry and the quantity of the flammable gas and oxygen. If there is sufficient oxygen inside the pipe during the compression process, an explosion can ignite immediately. If there is insufficient oxygen to initiate combustion inside the pipe, the flammable gas can only ignite if released to air, an oxygen rich environment. This presentation considers the fundamentals of gas compression and causes of ignition in nuclear reactor systems. In addition to these ignition mechanisms, specific applications are briefly considered. Those applications include a hydrogen fire following the Three Mile Island meltdown, hydrogen explosions following Fukushima Daiichi explosions, and on-going fires and explosions in U.S nuclear power plants. Novel conclusions are presented here as follows. 1. A hydrogen fire was ignited by water hammer at Three Mile Island. 2. Hydrogen explosions were ignited by water hammer at Fukushima Daiichi. 3. Piping damages in U.S. commercial nuclear reactor systems have occurred since reactors were first built. These damages were not caused by water hammer alone, but were caused by water hammer compression of flammable hydrogen and resultant deflagration or detonation inside of the piping.

Sensitivity Analyses for a PWR SCC Case Using the Probabilistic Loss-of-Coolant-Accident (Pro-LOCA) Software

2016 ◽  
Author(s):  
Bruce A. Young ◽  
Sang-Min Lee ◽  
Paul M. Scott
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
The United States ◽  
Design Criterion ◽  
Mitigation Strategies ◽  
Sensitivity Analyses ◽  
Base Case ◽  
Piping System ◽  
Loss Of Coolant Accident ◽  
Piping Systems

As a means of demonstrating compliance with the United States Code of Federal Regulations 10CFR50 Appendix A, General Design Criterion 4 (GDC-4) requirement that primary piping systems for nuclear power plants exhibit an extremely low probability of rupture, probabilistic fracture mechanics (PFM) software has become increasingly popular. One of these PFM codes for nuclear piping is Pro-LOCA which has been under development over the last decade. Currently, Pro-LOCA is being enhanced under an international cooperative program entitled PARTRIDGE-II (Probabilistic Analysis as a Regulatory Tool for Risk-Informed Decision GuidancE - Phase II). This paper focuses on the use of a pre-defined set of base-case inputs along with prescribed variation in some of those inputs to determine a comparative set of sensitivity analyses results. The benchmarking case was a circumferential Primary Water Stress Corrosion Crack (PWSCC) in a typical PWR primary piping system. The effects of normal operating loads, temperature, leak detection, inspection frequency and quality, and mitigation strategies on the rupture probability were studied. The results of this study will be compared to the results of other PFM codes using the same base-case and variations in inputs. This study was conducted using Pro-LOCA version 4.1.9.

Effects on Pipe Vibrations of Cavitation in an Orifice and in Globe-Style Valves

2006 ◽  
Author(s):  
Se´bastien Caillaud ◽  
Rene´-Jean Gibert ◽  
Pierre Moussou ◽  
Joe¨l Cohen ◽  
Fabien Millet
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Low Frequency ◽  
Flow Regimes ◽  
Piping System ◽  
Low Frequencies ◽  
Choked Flow ◽  
Single Hole ◽  
Piping Systems ◽  
Large Amplitude Vibrations

A piping system of French nuclear power plants displays large amplitude vibrations in particular flow regimes. These troubles are attributed to cavitation generated by single-hole orifices in depressurized flow regimes. Real scale experiments on high pressure test rigs and on-site tests are then conducted to explain the observed phenomenon and to find a solution to reduce pipe vibrations. The first objective of the present paper is to analyze cavitation-induced vibrations in the single-hole orifice. It is then shown that the orifice operates in choked flow with supercavitation, which is characterized by a large unstable vapor pocket. One way to reduce pipe vibrations consists in suppressing the orifices and in modifying the control valves. Three technologies involving a standard trim and anti-cavitation trims are tested. The second objective of the paper is to analyze cavitation-induced vibrations in globe-style valves. Cavitating valves operate in choked flow as the orifice. Nevertheless, no vapor pocket appears inside the pipe and no unstable phenomenon is observed. The comparison with an anti-cavitation solution shows that cavitation reduction has no impact on low frequency excitation. The effect of cavitation reduction on pipe vibrations, which involve essentially low frequencies, is then limited and the first solution, which is the standard globe-style valve installed on-site, leads to acceptable pipe vibrations. Finally, this case study may have consequences on the design of piping systems. First, cavitation in orifices must be limited. Choked flow in orifices may lead to supercavitation, which is here a damaging and unstable phenomenon. The second conclusion is that the reduction of cavitation in globe-style valve in choked flow does not reduce pipe vibrations. The issue is then to limit cavitation erosion of valve trims.

Evaluation of Representative Piping Systems Designed by Implicit Fatigue Concept

2008 ◽  
Author(s):  
Shin-Beom Choi ◽  
Sun-Hye Kim ◽  
Yoon-Suk Chang ◽  
Jae-Boong Choi ◽  
Young-Jin Kim ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Nuclear Power ◽  
Heat Removal ◽  
Environmental Water ◽  
Lessons Learned ◽  
Metal Fatigue ◽  
Aging Effects ◽  
Age Related ◽  
Piping Systems ◽  
Surge Line

NUREG-1801 provides generic aging lessons learned to manage aging effects that may occur during continued operation beyond the design life of nuclear power plant. According to this report, the metal fatigue, among several age-related degradation mechanisms, is identified as one of time-limited aging analysis item. The objective of this paper is to introduce fatigue life evaluation of representative surge line and residual heat removal system piping which was designed by implicit fatigue concept. For the back-fitting evaluation employing explicit fatigue concept, detailed parametric CFD as well as FE analyses results are used. The well-known ASME Section III NB-3600 procedure is adopted for the metal fatigue and NUREG/CR-5704 procedure is further investigated to deal with additional environmental water effects. With regard to the environmental effect evaluation, two types of fatigue life correction factors are considered, such as maximum Fen and individual Fen. As a result, it was proven that a thermal stratification phenomenon is the governing factor in metal fatigue life of the surge line and strain rate is the most important parameter affecting the environmental fatigue life of both piping. The evaluation results will be used as technical bases for continued operation of OPR 1000 plant.

Seismic Fragility of Piping Nozzles in Nuclear Power Plants: A Case for Updating the Current State-of-Practice

2021 ◽  
Author(s):  
Abhinav Gupta ◽  
Ankit Dubey ◽  
Sunggook Cho
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Seismic Analysis ◽  
Nuclear Industry ◽  
Life Extension ◽  
Seismic Loads ◽  
Thermal Loads ◽  
Loss Of Coolant Accident ◽  
Piping Systems ◽  
Recent Developments

Abstract Nuclear industry spends enormous time and resources on designing and managing piping nozzles in a plant. Nozzle locations are considered as a potential location for possible failure that can lead to loss of coolant accident. Industry spends enormous time in condition monitoring and margin management at nozzle locations. Margins against seismic loads play a significant role in the overall margin management. Available margins against thermal loads are highly dependent upon seismic margins. In recent years, significant international collaboration has been undertaken to study the seismic margin in piping systems and nozzles through experimental and analytical studies. It has been observed that piping nozzles are highly overdesigned and the margins against seismic loads are quite high. While this brings a perspective of sufficient safety, such excessively high margins compete with available margins against thermal loads particularly during the life extension and subsequent license renewal studies being conducted by many plants around the world. This paper focuses on identifying and illustrating two key reasons that lead to excessively conservative estimates of nozzle fragilities. First, it compares fragilities based on conventional seismic analysis that ignores piping-equipment-structure interaction on nozzle fragility with the corresponding assessment by considering such interactions. Then, it presents a case that the uncertainties considered in various parameters for calculating nozzle fragility are excessively high. The paper identifies a need to study the various uncertainties in order to achieve a more realistic quantification based on recent developments in our understanding of the seismic behavior of piping systems.

Sign in / Sign up

Export Citation Format

Share Document