A Three-Axis Piezoresistive Micromachined Force Sensor for Studying Cockroach Biomechanics

2000 ◽  
Author(s):  
Michael S. Bartsch ◽  
Aaron Partridge ◽  
Beth L. Pruitt ◽  
Robert J. Full ◽  
Thomas W. Kenny

Abstract A millimeter-scale silicon micromachined force sensor has been designed to measure in three axes the ground reaction forces produced by the cockroach Blaberus Discoidalis during typical running locomotion. Each sensor consists of a large-area (5mm × 5mm) rigid plate supported at its corners by thin flexures instrumented with two ion-implanted piezoresistors each. Comparison of piezoresistive measurements among these eight strain gauges allows the applied force to be resolved into three orthogonal components. Un-amplified sensitivity to normal forces of 1.2V/N has been demonstrated with estimated normal force resolution of 7.3μN on an 800Hz measurement bandwidth.

2021 ◽  
Vol 6 (1) ◽  
pp. 30
Author(s):  
Tayssir Limam ◽  
Florian Vogl ◽  
William R. Taylor

The measurement of ground reaction forces (GRFs) helps in determining the role of each limb for support and propulsion in predicting muscle activities, and in determining the strain conditions experienced by bones. Measuring the GRFs in mice models is therefore a cornerstone for understanding rodent musculoskeletal and neuromotor systems, as well as for improved translation of knowledge to humans. Current force plates are too big in size to allow the measurement of forces for each paw. This limitation is mainly due to the large size of the used sensors. The goal of our study was therefore to develop a small 3D force sensor for application in rodent gait analysis. We designed a flexible and small mechanical structure (8 mm × 8 mm) to isolate force components. Using FEM simulation, we chose the area with the highest strain to fix two strain gauges for each direction. The small size of the sensor allows us to fix four of them under a plate on the mouse paw size (approximately 17 mm). According to our primary results, the force plate has a resolution of 2 mN in the vertical direction and 1 mN in the fore-aft and mediolateral directions. The construction of a runway with such a force plate will allow the measurement of GRFs and the centre of pressure of each rodent paw for different steps. Such techniques thus provide a basis for assessing functionality in mice models, towards improved translation of rodent research.


2019 ◽  
Vol 9 (20) ◽  
pp. 4339 ◽  
Author(s):  
Lee ◽  
Chung ◽  
Oh ◽  
Cha

We have proposed a flexible sensor that can sense shear and normal forces, and can be fabricated through a simple process using only one layer of polyvinylidene fluoride (PVDF) film. For the measurement of shear and normal forces, one layer of PVDF film was sealed in a three-dimensionally structured polydimethylsiloxane (PDMS). In the structure, the sensor produced voltage signals corresponding to the shear and normal forces. Using this property, we aimed to demonstrate how to sense the magnitude and direction of the force applied to the sensor from its output voltages. Furthermore, the proposed sensor with a 2 × 2 array was able to measure the applied force in real time.


2019 ◽  
Vol 126 (5) ◽  
pp. 1315-1325 ◽  
Author(s):  
Andrew B. Udofa ◽  
Kenneth P. Clark ◽  
Laurence J. Ryan ◽  
Peter G. Weyand

Although running shoes alter foot-ground reaction forces, particularly during impact, how they do so is incompletely understood. Here, we hypothesized that footwear effects on running ground reaction force-time patterns can be accurately predicted from the motion of two components of the body’s mass (mb): the contacting lower-limb (m1 = 0.08mb) and the remainder (m2 = 0.92mb). Simultaneous motion and vertical ground reaction force-time data were acquired at 1,000 Hz from eight uninstructed subjects running on a force-instrumented treadmill at 4.0 and 7.0 m/s under four footwear conditions: barefoot, minimal sole, thin sole, and thick sole. Vertical ground reaction force-time patterns were generated from the two-mass model using body mass and footfall-specific measures of contact time, aerial time, and lower-limb impact deceleration. Model force-time patterns generated using the empirical inputs acquired for each footfall matched the measured patterns closely across the four footwear conditions at both protocol speeds ( r2 = 0.96 ± 0.004; root mean squared error  = 0.17 ± 0.01 body-weight units; n = 275 total footfalls). Foot landing angles (θF) were inversely related to footwear thickness; more positive or plantar-flexed landing angles coincided with longer-impact durations and force-time patterns lacking distinct rising-edge force peaks. Our results support three conclusions: 1) running ground reaction force-time patterns across footwear conditions can be accurately predicted using our two-mass, two-impulse model, 2) impact forces, regardless of foot strike mechanics, can be accurately quantified from lower-limb motion and a fixed anatomical mass (0.08mb), and 3) runners maintain similar loading rates (ΔFvertical/Δtime) across footwear conditions by altering foot strike angle to regulate the duration of impact. NEW & NOTEWORTHY Here, we validate a two-mass, two-impulse model of running vertical ground reaction forces across four footwear thickness conditions (barefoot, minimal, thin, thick). Our model allows the impact portion of the impulse to be extracted from measured total ground reaction force-time patterns using motion data from the ankle. The gait adjustments observed across footwear conditions revealed that runners maintained similar loading rates across footwear conditions by altering foot strike angles to regulate the duration of impact.


Animals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 436 ◽  
Author(s):  
Hilary Mary Clayton ◽  
Sarah Jane Hobbs

The piaffe is an artificial, diagonally coordinated movement performed in the highest levels of dressage competition. The ground reaction forces (GRFs) of horses performing the piaffe do not appear to have been reported. Therefore, the objective of this study was to describe three-dimensional GRFs in ridden dressage horses performing the piaffe. In-ground force plates were used to capture fore and hindlimb GRF data from seven well-trained dressage horses. Peak vertical GRF was significantly higher in forelimbs than in the hindlimbs (7.39 ± 0.99 N/kg vs. 6.41 ± 0.64 N/kg; p < 0.001) with vertical impulse showing a trend toward higher forelimb values. Peak longitudinal forces were small with no difference in the magnitude of braking or propulsive forces between fore and hindlimbs. Peak transverse forces were similar in magnitude to longitudinal forces and were mostly directed medially in the hindlimbs. Both the intra- and inter-individual variability of longitudinal and transverse GRFs were high (coefficient of variation 25–68%). Compared with the other diagonal gaits of dressage horses, the vertical GRF somewhat shifted toward the hindlimbs. The high step-to-step variability of the horizontal GRF components is thought to reflect the challenge of balancing on one diagonal pair of limbs with no forward momentum.


2007 ◽  
Vol 46 (3) ◽  
pp. 491-499 ◽  
Author(s):  
Melissa M. Scott-Pandorf ◽  
Nicholas Stergiou ◽  
Jason M. Johanning ◽  
Leon Robinson ◽  
Thomas G. Lynch ◽  
...  

Sensors ◽  
2019 ◽  
Vol 19 (9) ◽  
pp. 2011 ◽  
Author(s):  
Bessone ◽  
Petrat ◽  
Schwirtz

In the past, technological issues limited research focused on ski jump landing. Today, thanks to the development of wearable sensors, it is possible to analyze the biomechanics of athletes without interfering with their movements. The aims of this study were twofold. Firstly, the quantification of the kinetic magnitude during landing is performed using wireless force insoles while 22 athletes jumped during summer training on the hill. In the second part, the insoles were combined with inertial motion units (IMUs) to determine the possible correlation between kinematics and kinetics during landing. The maximal normal ground reaction force (GRFmax) ranged between 1.1 and 5.3 body weight per foot independently when landing using the telemark or parallel leg technique. The GRFmax and impulse were correlated with flying time (p < 0.001). The hip flexions/extensions and the knee and hip rotations of the telemark front leg correlated with GRFmax (r = 0.689, p = 0.040; r = −0.670, p = 0.048; r = 0.820, p = 0.007; respectively). The force insoles and their combination with IMUs resulted in promising setups to analyze landing biomechanics and to provide in-field feedback to the athletes, being quick to place and light, without limiting movement.


Sign in / Sign up

Export Citation Format

Share Document