Baseline, Exhaust-Fired, and Combined Operation of Desiccant Dehumidification Unit

2004 ◽  
Author(s):  
Andrei Yu. Petrov ◽  
Abdolreza Zaltash ◽  
Edward A. Vineyard ◽  
Solomon D. Labinov ◽  
D. Tom Rizy ◽  
...  
Keyword(s):  
Natural Gas ◽  
Power Output ◽  
Waste Heat ◽  
Hot Water ◽  
Dew Point ◽  
Low Grade ◽  
Oak Ridge ◽  
Gas Burner ◽  
The Impact ◽  
Combined Mode

The performance of a commercially available direct-fired desiccant dehumidification unit (DFDD) has been studied as part of a microturbine generator (MTG)-based Integrated Energy System (IES) at Oak Ridge National Laboratory (ORNL). The IES includes a second-generation air-to-water heat recovery unit (HRU) for the MTG. The focus of these tests was to study the performance of a DFDD in baseline (direct-fired with its natural gas burner) mode and to compare it with a DFDD performance in the exhaust-fired and combined modes as part of the ORNL IES, when waste heat received from the MTG was used for desiccant regeneration. The baseline tests were performed with regeneration air heated by a natural gas burner (direct-fired). The testing of the waste-heat, or exhaust-fired DFDD as part of IES involved using the exhaust gas from the HRU for regeneration air in the DFDD after hot water production in the HRU. Hot water from the HRU was used to produce chilled water in an indirect-fired (water fired) absorption chiller. The combined DFDD was the combination of natural gas burner and exhaust-fired testing. The study investigated the impact of varying the process and regeneration conditions on the latent capacity (LC) and latent coefficient of performance (LCOP) of the DFDD, as well as overall IES efficiency. The performance tests show that LC increases with increasing dew point (humidity ratio) of the process air or the increased amount of waste heat associated with increased MTG power output. In addition, baseline LC was found to be three times higher than the LC in the exhaust-fired mode of operation. LCOP in baseline operation is also almost three times higher than that obtained in the exhaust-fired mode (55.4% compared to 19%). But, at the same time, addition of the DFDD to the IES with the MTG at maximum power output increases the overall IES efficiency by 4–5%. Results of the combined tests performed at a reduced MTG power output of 15 kW (51,182 Btu/h) and their comparison with the baseline and exhaust-fired tests show that activation of the DFDD gas burner during exhaust-fired tests increases the LC over the baseline value from 91,514.9 Btu/h (25.8 kW) to 101,835.8 Btu/h (29.8 kW). The LCOP during the combined mode is less than the “baseline” LCOP, because in addition to gas input, the low-grade MTG/HRU exhaust heat input to the DFDD are also being considered. The overall IES efficiency during the combined mode is approximately 8% higher than without the DFDD integrated into the IES.

scholarly journals Performance Characteristics of Solid-Desiccant Evaporative Cooling Systems

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2574 ◽  
Author(s):  
Ramadas Narayanan ◽  
Edward Halawa ◽  
Sanjeev Jain
Keyword(s):  
Air Conditioning ◽  
Natural Ventilation ◽  
Waste Heat ◽  
Numerical Study ◽  
Evaporative Cooling ◽  
Peak Load ◽  
Dew Point ◽  
Low Grade ◽  
Subtropical Climate ◽  
Cooling Systems

Air conditioning accounts for up to 50% of energy use in buildings. Increased air-conditioning-system installations not only increase total energy consumption but also raise peak load demand. Desiccant evaporative cooling systems use low-grade thermal energy, such as solar energy and waste heat, instead of electricity to provide thermal comfort. This system can potentially lead to significant energy saving, reduction in carbon emissions, and it has a low dew-point operation and large capacity range. Their light weight, simplicity of design, and close-to-atmospheric operation make them easy to maintain. This paper evaluates the applicability of this technology to the climatic conditions of Brisbane, Queensland, Australia, specifically for the residential sector. Given the subtropical climate of Brisbane, where humidity levels are not excessively high during cooling periods, the numerical study shows that such a system can be a potential alternative to conventional compression-based air-conditioning systems. Nevertheless, the installation of such a system in Brisbane’s climate zone requires careful design, proper selection of components, and a cheap heat source for regeneration. The paper also discusses the economy-cycle options for this system in such a climate and compares its effectiveness to natural ventilation.

Experimental Investigation of the Impact of Biogas on a 3 kW Micro Gas Turbine FLOX®-Based Combustor

2020 ◽  
Author(s):  
Hannah Seliger-Ost ◽  
Peter Kutne ◽  
Jan Zanger ◽  
Manfred Aigner
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Waste Heat ◽  
Electrical Power ◽  
Atmospheric Conditions ◽  
Micro Gas Turbine ◽  
Fuel Mixtures ◽  
Carbon Dioxide Co2 ◽  
Electrical Power Output ◽  
The Impact

Abstract The use of biogas has currently two disadvantages. Firstly, processing biogas to natural gas quality for feeding into the natural gas grid is a rather energy consuming process. Secondly, the conversion into electricity directly in biogas plants produces waste heat, which largely cannot be used. Therefore, a feed-in of the desulfurized and dry biogas to local biogas grids would be preferable. Thus, the biogas could be used directly at the end consumer for heat and power production. As biogas varies in its methane (CH4) and carbon dioxide (CO2) content, respectively, this paper studies the influence of different biogas mixtures compared to natural gas on the combustion in a FLOX®-based six nozzle combustor. The single staged combustor is suitable for the use in a micro gas turbine (MGT) based combined heat and power (CHP) system with an electrical power output of 3 kW. The combustor is studied in an optically accessible atmospheric test rig, as well as integrated into the MGT system. This paper focuses on the influence of the admixture of CO2 to natural gas on the NOX and CO emissions. Furthermore, at atmospheric conditions the shape and location of the heat release zone is investigated using OH* chemiluminescence (OH* CL). The combustor could be stably operated in the MGT within the complete stationary operating range with all fuel mixtures.

Low Emissions, Renewable, Dispatchable Power Generation Using Ethanol/Natural Gas Blends

2014 ◽  
Author(s):  
Maclain M. Holton ◽  
Michael S. Klassen ◽  
Leo D. Eskin ◽  
Richard J. Joklik ◽  
Richard J. Roby
Keyword(s):  
Power Generation ◽  
Heat Exchanger ◽  
Natural Gas ◽  
Power Output ◽  
Gas Turbines ◽  
Waste Heat ◽  
Full Range ◽  
Liquid Fuels ◽  
Power Sources ◽  
Pollution Levels

Nearly all states now have renewable portfolio standards (RPS) requiring electricity suppliers to produce a certain fraction of their electricity using renewable sources. Many renewable energy technologies have been developed to contribute to RPS requirements, but these technologies lack the advantage of being a dispatchable source which would give a grid operator the ability to quickly augment power output on demand. Gas turbines burning biofuels can meet the need of being dispatchable while using renewable fuels. However, traditional combustion of liquid fuels would not meet the pollution levels of modern dry, low emission (DLE) gas turbines burning natural gas without extensive back-end clean-up. A Lean, Premixed, Prevaporized (LPP) combustion technology has been developed to vaporize liquid ethanol and blend it with natural gas creating a mixture which can be burned in practically any combustion device in place of ordinary natural gas. The LPP technology delivers a clean-burning gas which is able to fuel a gas turbine engine with no alterations made to the combustor hardware. Further, the fraction of ethanol blended in the LPP gas can be quickly modulated to maintain the supplier’s overall renewable quotient to balance fluctuations in power output of less reliable renewable power sources such as wind and solar. The LPP technology has successfully demonstrated over 1,000 hours of dispatchable power generation on a 30 kW Capstone C30 microturbine using vaporized liquid fuels. The full range of fuel mixtures ranging from 100% methane with no ethanol addition to 100% ethanol with no methane addition have been burned in the demonstration engine. Emissions from ethanol/natural gas mixtures have been comparable to baseline natural gas emissions of 3 ppm NOx and 30 ppm CO. Waste heat from the combustor exhaust is recovered in an indirect heat exchanger and is used to vaporize the ethanol as it is blended with natural gas. This design allows for startup on natural gas and blending of vaporized ethanol once the heat exchanger has reached its operating temperature.

scholarly journals Energy and Exergy Analysis of Different Exhaust Waste Heat Recovery Systems for Natural Gas Engine Based on ORC

Energies ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 2378 ◽  
Author(s):  
Guillermo Valencia ◽  
Armando Fontalvo ◽  
Yulineth Cárdenas ◽  
Jorge Duarte ◽  
Cesar Isaza
Keyword(s):  
Natural Gas ◽  
Conversion Efficiency ◽  
Power Output ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Gas Engine ◽  
Natural Gas Engine ◽  
Energy And Exergy ◽  
Net Power Output

Waste heat recovery (WHR) from exhaust gases in natural gas engines improves the overall conversion efficiency. The organic Rankine cycle (ORC) has emerged as a promising technology to convert medium and low-grade waste heat into mechanical power and electricity. This paper presents the energy and exergy analyses of three ORC–WHR configurations that use a coupling thermal oil circuit. A simple ORC (SORC), an ORC with a recuperator (RORC), and an ORC with double-pressure (DORC) configuration are considered; cyclohexane, toluene, and acetone are simulated as ORC working fluids. Energy and exergy thermodynamic balances are employed to evaluate each configuration performance, while the available exhaust thermal energy variation under different engine loads is determined through an experimentally validated mathematical model. In addition, the effect of evaporating pressure on the net power output, thermal efficiency increase, specific fuel consumption, overall energy conversion efficiency, and exergy destruction is also investigated. The comparative analysis of natural gas engine performance indicators integrated with ORC configurations present evidence that RORC with toluene improves the operational performance by achieving a net power output of 146.25 kW, an overall conversion efficiency of 11.58%, an ORC thermal efficiency of 28.4%, and a specific fuel consumption reduction of 7.67% at a 1482 rpm engine speed, a 120.2 L/min natural gas flow, 1.784 lambda, and 1758.77 kW of mechanical engine power.

Hybrid Dual-Fuel Combined Cycles: General Performance Analysis

2002 ◽  
Author(s):  
Miroslav P. Petrov ◽  
Andrew R. Martin ◽  
Laszlo Hunyadi
Keyword(s):  
Natural Gas ◽  
Power Plants ◽  
Small Scale ◽  
Dual Fuel ◽  
Low Grade ◽  
Steam Boiler ◽  
Electrical Efficiency ◽  
Combined Cycles ◽  
Gas Fuel ◽  
The Impact

The hybrid dual-fuel combined cycle concept is a promising technology for increasing the energy utilization of low-grade (solid) fuels. Advantages such as enhanced electrical efficiency, favorable economics, and relative ease of construction and operation have been pointed out by various authors in previous studies. The present investigation aims to assess the performance of natural gas and coal- or biomass-fired hybrid combined cycles, with a gas turbine as topping cycle and a steam boiler as bottoming cycle. A parametric analysis considers the impact of the natural gas/solid fuel energy ratio on the electrical efficiency of various hybrid system configurations. Results show that significant performance improvements (in the order of several percentage points in electrical efficiency) can be achieved by these hybrid configurations when compared to the reference (two independent, single-fuel power plants at the given scales). In large-scale power plants with coal-fired bottoming cycle, efficiencies continuously rise as the share of natural gas fuel is increased up to the cycle integration limits, while an optimum can be seen for the small-scale biomass-fired bottoming cycles (with modest steam parameters) at a certain share of natural gas fuel input.

scholarly journals Heat Pump Use in Rural District Heating Networks in Estonia

2021 ◽  
Vol 25 (1) ◽  
pp. 786-802
Author(s):  
Kertu Lepiksaar ◽  
Kiur Kalme ◽  
Andres Siirde ◽  
Anna Volkova
Keyword(s):  
Heat Pump ◽  
Renewable Energy Sources ◽  
District Heating ◽  
Ambient Air ◽  
Heat Pumps ◽  
Hot Water ◽  
Rural District ◽  
Low Grade ◽  
The Impact ◽  
Heating Networks

Abstract District heating has proven to be an efficient way of providing space heating and domestic hot water in populated areas. It has also proven to be an excellent way to integrate various renewable energy sources (RES) into the energy system. In Estonia, biomass covers most of the heat demand, but carbon-intensive fuels are still used to cover peaks and lows. Heat pumps can be a good solution for rural areas, as there is usually plenty of land available for heat pump facilities. In addition, heat pumps require low-grade heat sources such as ambient air, groundwater, lakes, rivers, sea, sewage water, and industrial waste heat. One of the downsides of heat pumps is the need for large investments compared to boilers fired by natural gas and biomass, and electric boilers. This study examines the impact of heat pump use on consumer prices for district heating in rural district heating networks in Estonia.

scholarly journals Numerical assessment of a gas-fired condensing boiler model for residential buildings application

2021 ◽  
Vol 2116 (1) ◽  
pp. 012016
Author(s):  
K Simic ◽  
I T’Jollyn ◽  
W Faes ◽  
J Borrajo Bastero ◽  
J Laverge ◽  
...  
Keyword(s):  
Natural Gas ◽  
Input Data ◽  
Numerical Models ◽  
Residential Buildings ◽  
Software Tool ◽  
Heat Transfer Process ◽  
Hot Water ◽  
Dew Point ◽  
The European Union ◽  
Combustion Gases

Abstract According to the official statistical reports, gas-fired boiler units still remain to be one of the main equipment types for meeting the space heating and daily hot water demand of the residential dwellings across the European Union. Due to the prevalence of the natural gas grid and performance stability, gas-fired boilers are considered to remain as one of the standard energy sources. On the other hand, even though gas-fired water heating technology is a well-known concept, existing numerical models found in the literature are often case-specific with poor reusability mostly reflected in fitted efficiencies. Algorithms behind these models usually require the input of large amount of hardly attainable design characteristics of the units. In this paper, a modelling method for acquiring the performance of a heating gas-fired condensing boiler unit will be shown. The model is based on the limited input data available in the official characteristics of the units issued by the relevant manufacturers. The simulations are programmed by using the programming language Modelica and the software tool Dymola. The model is based on the fixed natural gas intake which combusts into a stable mixture of the combustion gases that further heat the circulating water. During the heat transfer process inside the condensing boilers there is a possibility for condensate formation out of the water vapour of the combustion gases which increases the efficiency of the unit. The formation of condensate, however, is depending on the return water temperature of the unit which has to be lower than the dew point temperature of the combustion gasses. The goal of this research is to determine how accurate can performance indicators of gas-fired boilers be attained with the use of a limited amount of available input data together with clearly defined assumptions that follow the modelling methodology.

Sign in / Sign up

Export Citation Format

Share Document