Parametric Analysis of a Bayonet Tube With a Special Type of Extended Surface

2010 ◽  
Author(s):  
L. Almanza-Huerta ◽  
A. Hernandez-Guerrero ◽  
M. Krarti ◽  
J. M. Luna
Keyword(s):  
Heat Transfer ◽  
Parametric Analysis ◽  
Numerical Study ◽  
Systematic Investigation ◽  
Heat Transfer Characteristics ◽  
Maximum Heat ◽  
Turbulent Transition ◽  
Maximum Heat Transfer ◽  
Internal Fluid ◽  
Extended Surface

The present paper provides a numerical study of a parametric analysis of a bayonet tube with a special type of extended surface during the laminar-turbulent transition. The working internal fluid is air. Attention is focused on the heat transfer characteristics of the tube. The results constitute a systematic investigation of the effect of the extended surface located along the annulus of the bayonet on the overall heat transfer rate. The effects of the variation of some parameters related to the extended surface aiming to attain the maximum heat transfer with the minimum pressure drop are discussed. Comparisons between designs with and without extended surface are also made.

scholarly journals Flow and heat transfer characteristics downstream of a porous sudden expansion: A numerical study

2011 ◽  
Vol 15 (2) ◽  
pp. 389-396 ◽  
Author(s):  
Khalid Alammar
Keyword(s):  
Heat Transfer ◽  
Numerical Study ◽  
Darcy Number ◽  
Sudden Expansion ◽  
Heat Transfer Characteristics ◽  
Maximum Heat ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Maximum Heat Transfer ◽  
Inertia Coefficient

Incompressible, axisymmetric laminar flow downstream of a porous expansion is simulated. Effect of the Darcy number and inertia coefficient on flow and heat transfer characteristics downstream of the expansion is investigated. The simulation revealed circulation downstream of the expansion. Decreasing the Darcy number is shown to decrease the circulation region. The Nusselt number, friction coefficient, and pressure drop are shown to increase, while reattachment and location of maximum heat transfer move upstream with decreasing Darcy number. Similar effects are observed with increasing inertia coefficient.

Effect of Periodicity of Non-Uniform Sinusoidal Side Heating on Natural Convection in an Anisotropic Porous-Enclosure

2011 ◽  
Vol 110-116 ◽  
pp. 1613-1618 ◽  
Author(s):  
S. Kapoor ◽  
P. Bera
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Stream Function ◽  
Numerical Study ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Porous Enclosure

A comprehensive numerical study on the natural convection in a hydrodynamically anisotropic as well as isotropic porous enclosure is presented, flow is induced by non uniform sinusoidal heating of the right wall of the enclosure. The principal directions of the permeability tensor has been taken oblique to the gravity vector. The spectral Element method has been adopted to solve numerically the governing differential equations by using the vorticity-stream-function approach. The results are presented in terms of stream function, temperature profile and Nusselt number. The result show that the maximum heat transfer takes place at y = 1.5 when N is odd.. Also, increasing media permeability, by changing K* = 1 to K* = 0.2, increases heat transfer rate at below and above right corner of the enclosure. Furthermore, for the all values of N, profiles of local Nusselt number (Nuy) in isotropic as well as anisotropic media are similar, but for even values of N differ slightly at N = 2.. In particular the present analysis shows that, different periodicity (N) of temperature boundary condition has the significant effect on the flow pattern and consequently on the local heat transfer phenomena.

scholarly journals Numerical study of gas dynamics and heat transfer in matrix channels at various rib angles

2021 ◽  
Vol 2057 (1) ◽  
pp. 012026
Author(s):  
A V Barsukov ◽  
V V Terekhov ◽  
V I Terekhov
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Reynolds Number ◽  
Gas Dynamics ◽  
Average Velocity ◽  
Numerical Study ◽  
Reynolds Numbers ◽  
Separation Flow ◽  
Maximum Heat ◽  
Maximum Heat Transfer

Abstract The results of numerical simulation of the separation flow in matrix channels by the RANS method are presented. The simulation is performed at the Reynolds number Re = 12600, determined by the mass-average velocity and the height of the channel. The distribution of the local Nusselt number is obtained for various Reynolds numbers in the range of 5÷15⋅103 and several rib angles. It is shown that the temperature distribution on the surface is highly nonuniform; in particular, the maximum heat transfer value is observed near the upper edge facets, in the vicinity of which the greatest velocity gradient is observed.

A Numerical Study of Heat Transfer Enhancement by a Rectangular Cylinder Placed Parallel to the Heated Wall

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
J. F. Derakhshandeh ◽  
Md. Mahbub Alam
Keyword(s):  
Heat Transfer ◽  
Vortex Dynamics ◽  
Numerical Study ◽  
Vortex Street ◽  
Heated Wall ◽  
Transfer Enhancement ◽  
Maximum Heat ◽  
Single Row ◽  
Rectangular Cylinder ◽  
Maximum Heat Transfer

The flow around a rectangular cylinder mounted in the vicinity of a hot wall is numerically studied at a Reynolds number of 200. While the cylinder chord-to-height ratio C/W is varied from 2 to 10, the gap distance G from the wall to the cylinder is changed from 0.25 to 6.25. The focus of this study is given on the dependence of G/W and C/W on the heat transfer from the wall and associated physics. The variation in the Strouhal number is presented as a function of C/W. It is observed that the effect of G/W on the vortex dynamics and heat transfer is much more than that of C/W. Based on the dependence of the vortex dynamics and heat transfer on G/W, we have identified four distinct flows: no vortex street flow (G/W < 0.75), single-row vortex street flow (0.75 ≤ G/W ≤ 1.25), inverted two-row vortex street flow (1.25 < G/W ≤ 2.5), and two-row vortex street flow (G/W > 2.5). At the single-row vortex street flow, the two opposite-sign vortices appearing in a jetlike flow carry heat from the wall to the wake and then to the freestream. The maximum heat transfer is achieved at the single-row vortex street flow and 8% increase occurs at C/W = 2, G/W = 0.75–1.25.

scholarly journals Numerical Study on Flow and Heat Transfer Mechanisms in the Heat Exchanger Channel with V-Orifice at Various Blockage Ratios, Gap Spacing Ratios, and Flow Directions

2019 ◽  
Vol 2019 ◽  
pp. 1-21 ◽  
Author(s):  
Amnart Boonloi ◽  
Withada Jedsadaratanachai
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Numerical Study ◽  
Numerical Results ◽  
Blockage Ratio ◽  
Maximum Heat ◽  
Flow And Heat Transfer ◽  
Maximum Heat Transfer ◽  
Smooth Channel ◽  
Gap Spacing

Numerical assessments in the square channel heat exchanger installed with various parameters of V-orifices are presented. The V-orifice is installed in the heat exchanger channel with gap spacing between the upper-lower edges of the orifice and the channel wall. The purposes of the design are to reduce the pressure loss, increase the vortex strength, and increase the turbulent mixing of the flow. The influence of the blockage ratio and V-orifice arrangement is investigated. The blockage ratio, b/H, of the V-orifice is varied in the range 0.05–0.30. The V-tip of the V-orifice pointing downstream (V-downstream) is compared with the V-tip pointing upstream (V-upstream) by both flow and heat transfer. The numerical results are reported in terms of flow visualization and heat transfer pattern in the test section. The thermal performance assessments in terms of Nusselt number, friction factor, and thermal enhancement factor are also concluded. The numerical results reveal that the maximum heat transfer enhancement is found to be around 26.13 times higher than the smooth channel, while the optimum TEF is around 3.2. The suggested gap spacing for the present configuration of the V-orifice channel is around 5–10%.

Study of Flow and Convective Heat Transfer in a Simulated Scaled Up Low Emission Annular Combustor

2011 ◽  
Vol 3 (3) ◽  
Author(s):  
Sunil Patil ◽  
Teddy Sedalor ◽  
Danesh Tafti ◽  
Srinath Ekkad ◽  
Yong Kim ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Convective Heat ◽  
Swirling Flow ◽  
Numerical Study ◽  
Swirl Number ◽  
Maximum Heat ◽  
Number Range ◽  
Maximum Heat Transfer ◽  
Annular Combustor

Modern dry low emissions (DLE) combustors are characterized by highly swirling and expanding flows that makes the convective heat load on the gas side difficult to predict and estimate. A coupled experimental–numerical study of swirling flow inside a DLE annular combustor model is used to determine the distribution of heat transfer on the liner walls. Three different Reynolds numbers are investigated in the range of 210,000–840,000 with a characteristic swirl number of 0.98. The maximum heat transfer coefficient enhancement ratio decreased from 6 to 3.6 as the flow Reynolds number increased from 210,000 to 840,000. This is attributed to a reduction in the normalized turbulent kinetic energy in the impinging shear layer, which is strongly dependent on the swirl number that remains constant at 0.98 for the Reynolds number range investigated. The location of peak heat transfer did not change with the increase in Reynolds number since the flow structures in the combustors did not change with Reynolds number. Results also showed that the heat transfer distributions in the annulus have slightly different characteristics for the concave and convex walls. A modified swirl number accounting for the step expansion ratio is defined to facilitate comparison between the heat transfer characteristics in the annular combustor with previous work in a can combustor. A higher modified swirl number in the annular combustor resulted in higher heat transfer augmentation and a slower decay with Reynolds number.

Heat Transfer in Internally Finned Tubes

1976 ◽  
Vol 98 (2) ◽  
pp. 257-261 ◽  
Author(s):  
J. H. Masliyah ◽  
K. Nandakumar
Keyword(s):  
Heat Transfer ◽  
Circular Tube ◽  
Uniform Heat Flux ◽  
Heat Transfer Characteristics ◽  
Fully Developed Flow ◽  
Maximum Heat ◽  
Finned Tubes ◽  
Maximum Heat Transfer ◽  
Internal Fins ◽  
Laminar Forced Convection

Heat transfer characteristics for a laminar forced convection fully developed flow in an internally finned circular tube with axially uniform heat flux with peripherally uniform temperature are obtained using a finite element method. For a given fin geometry, the Nusselt number based on inside tube diameter was higher than that for a smooth tube. Also, it was found that for maximum heat transfer there exists an optimum fin number for a given fin configuration. The internal fins are of triangular shape.

Heat Transfer of Sprays of Large Water Drops Impacting on High Temperature Surfaces

1999 ◽  
Vol 121 (2) ◽  
pp. 446-450 ◽  
Author(s):  
T. L. Cox ◽  
S. C. Yao
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Current Data ◽  
Large Droplet ◽  
Heat Transfer Characteristics ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Water Drops ◽  
Large Water ◽  
Transfer Potential

Experiments were performed to evaluate the heat transfer of monodisperse sprays of large droplet diameters, ranging from 3 to 25 mm, on high temperature surfaces. This range of drop sizes has not previously been studied, and it was of interest to determine their heat transfer characteristics and how they relate to sprays of smaller drops. Parametric tests showed that the spray heat flux depends on mass flux with a power-law relationship, and that spray effectiveness, which relates the actual spray heat transfer to the maximum heat transfer potential, varies with d−1/2. There was no discernible relationship between the heat transfer and droplet velocity. These results agreed favorably with published results for smaller droplets. The current data was compared to previous tests with smaller droplets using the droplet Reynolds and Weber numbers. This analysis showed some grouping, with a marked separation at We = 80, where the dynamic behavior of droplets has been shown to change for nonwetting impaction.

A Numerical Study of the Natural Convection in CPC Solar Collector Cavities with Tubular Absorbers

1989 ◽  
Vol 111 (1) ◽  
pp. 16-23 ◽  
Author(s):  
T. C. Chew ◽  
A. O. Tay ◽  
N. E. Wijeysundera
Keyword(s):  
Heat Transfer ◽  
Tilt Angle ◽  
Solar Collector ◽  
Numerical Study ◽  
Cover Plate ◽  
Maximum Heat ◽  
Transfer Rates ◽  
Maximum Heat Transfer ◽  
Contour Plots ◽  
Flat Cover

The laminar free convection in a compound parabolic concentrator (CPC) solar collector cavity is numerically simulated using the finite element method. Results are presented for representative CPC collectors with tubular absorbers of concentration ratio 2. The effect of Grashof number, truncation and tilt angle were investigated. Generally, higher rates of heat transfer between the tubular absorber and the flat cover plate of the cavity are associated with larger Grashof numbers and shallower cavities. The maximum heat transfer rates occur when the tilt angle is about 60 deg. Contour plots are obtained for the field variables and these provide an insight into the spatial characteristics of the convective mechanisms within the cavity.

Numerical Analysis of Natural Convective Heat Transfer over a Vertical Cylinder Using External Fins

2015 ◽  
Vol 813-814 ◽  
pp. 707-712
Author(s):  
Anwesha Panigrahi ◽  
D.P. Mishra ◽  
Deepak Kumar
Keyword(s):  
Heat Transfer ◽  
Numerical Investigation ◽  
Numerical Study ◽  
Convection Heat Transfer ◽  
Vertical Cylinder ◽  
Working Fluid ◽  
Natural Convection Heat Transfer ◽  
Maximum Heat ◽  
Optimum Parameters ◽  
Maximum Heat Transfer

The present numerical study deals with the natural convection heat transfer on the surface of a vertical cylinder with external longitudinal fins. The aim of the study was to determine the effects of geometric parameters like fin height, fin number and fin shape on the heat transfer and thus obtain the optimum parameters that will maximize the rate of heat transfer have been discussed. The numerical investigation consists of an aluminium cylinder of length 1m and diameter 0.07m with air as the working fluid. It has been seen from the numerical investigation that the heat transfer increases with fin height. It is also observed that there exists optimum fin number for maximum heat transfer. Keeping the fin number, fin height and volume fixed, it was found that the heat transfer is maximum for rectangular shaped fin.

Sign in / Sign up

Export Citation Format

Share Document