Radial, Two-Phase Heat Transport Device Driven by Electrohydrodynamic Conduction Pumping

2011 ◽  
Author(s):  
Matthew R. Pearson ◽  
Jamal Seyed-Yagoobi
Keyword(s):  
Thin Film ◽  
Heat Flux ◽  
Heat Source ◽  
Liquid Film ◽  
Heat Pipe ◽  
Heat Transport ◽  
Working Fluid ◽  
Bottom Surface ◽  
Two Phase ◽  
Transport Device

Electrohydrodynamic (EHD) conduction pumping can be readily used to pump a thin film of a dielectric liquid along a surface, using electrodes that are embedded into the surface. This effect has been demonstrated under adiabatic conditions and has also been used to create a two-phase heat transport device that is similar to a heat pipe, but with the wicking structure replaced by an EHD conduction pump. In this study, a circular two-phase heat transport device is created. The device features circular electrodes that are arranged concentrically on the bottom surface and that pump a liquid film towards a heat source located at the center of the device. This heat source evaporates the liquid, and a large annular condenser at the periphery of the bottom surface provides a continuous supply of fresh liquid. This radial pumping configuration provides several advantages. Most notably, the heat source is wetted with fresh liquid from all 360 degrees, thereby reducing the amount of distance that must be travelled compared to a linear device. Consequently, the heat flux that can be removed from the central heat source far exceeds the normal critical heat flux of the working fluid. Electrodes are embedded in the condenser, adiabatic, and evaporator sections to maximize the amount of pumping head that can be generated and thereby maximize the heat flux removal.

Effect of Thin Film Condensation on Thermal Performance of Oscillating Heat Pipes

2006 ◽  
Author(s):  
S. B. Liang ◽  
G. P. Xu
Keyword(s):  
Thin Film ◽  
Liquid Film ◽  
Heat Pipe ◽  
Heat Transport ◽  
Slug Flow ◽  
Thin Liquid Film ◽  
Experimental Studies ◽  
Heat Pipes ◽  
Film Condensation ◽  
Working Fluid

Self-sustainable motions of the slug flow in oscillating heat pipes have been investigated in the paper. Thin film condensation in the capillary channels of the condenser of the oscillating heat pipes was studied. Instability of the thin liquid film on the characteristics of heat pipes was analysed. The extra thermal resistance caused by the thickness of the thin liquid film was taken into account for the numerical simulation of the oscillatory motions of the slug flow in the heat pipes. Saturated temperatures and pressures of the working fluid in the condenser were obtained. Thermoacoustic theory was applied to calculate heat transport through the adiabatic section of the heat pipes. Experimental studies were carried out to understand the heat transfer behaviours of heat pipes. One heat pipe with the working fluid of HFC-134a was evaluated. The heat pipe is made of aluminium plate and has the width of 50 mm and thickness of 1.9 mm. Numerical and experimental results relevant to the heat transport capability of the heat pipe were analysed and compared.

Experimental Study of Linear and Radial Two-Phase Heat Transport Devices Driven by Electrohydrodynamic Conduction Pumping

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
Matthew R. Pearson ◽  
Jamal Seyed-Yagoobi
Keyword(s):  
Heat Source ◽  
Capillary Pressure ◽  
Heat Transport ◽  
Radial Direction ◽  
Heat Pipes ◽  
Working Fluid ◽  
Phase Flow ◽  
Transport Capacity ◽  
Two Phase ◽  
Capillary Phenomenon

Heat pipes are well known as simple and effective heat transport devices, utilizing two-phase flow and the capillary phenomenon to remove heat. However, the generation of capillary pressure requires a wicking structure and the overall heat transport capacity of the heat pipe is generally limited by the amount of capillary pressure generation that the wicking structure can achieve. Therefore, to increase the heat transport capacity, the capillary phenomenon must be either augmented or replaced by some other pumping technique. Electrohydrodynamic (EHD) conduction pumping can be readily used to pump a thin film of a dielectric liquid along a surface, using electrodes that are embedded into the surface. In this study, two two-phase heat transport devices are created. The first device transports the heat in a linear direction. The second device transports the heat in a radial direction from a central heat source. The radial pumping configuration provides several advantages. Most notably, the heat source is wetted with fresh liquid from all directions, thereby reducing the amount of distance that must be travelled by the working fluid. The power required to operate the EHD conduction pumps is a trivial amount relative to the heat that is transported.

Heat Transport Characteristics in Closed Loop Oscillating Heat Pipes

2005 ◽  
Author(s):  
Shuangfeng Wang ◽  
Shigefumi Nishio
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Closed Loop ◽  
Flow Behavior ◽  
Working Fluid ◽  
Liquid Volume ◽  
High Heat Flux ◽  
Two Phase ◽  
Working Fluids ◽  
Inner Diameter

Heat transport rates of micro scale SEMOS (Self-Exciting Mode Oscillating) heat pipe with inner diameter of 1.5mm, 1.2mm and 0.9mm, were investigated by using R141b, ethanol and water as working fluids. The effects of inner diameter, liquid volume faction, and material properties of the working fluids are examined. It shows that the smaller the inner diameter, the higher the thermal transport density is. For removing high heat flux, the water is the most promising working fluid as it has the largest critical heat transfer rate and the widest operating range among the three kinds of working fluids. A one-dimensional numerical simulation is carried out to describe the heat transport characteristics and the two-phase flow behavior in the closed loop SEMOS heat pipe. The numerical prediction agrees with the experimental results fairly well, when the input heat through was not very high and the flow pattern was slug flow.   This paper was also originally published as part of the Proceedings of the ASME 2005 Pacific Rim Technical Conference and Exhibition on Integration and Packaging of MEMS, NEMS, and Electronic Systems.

Effect of Fluid Loading on the Performance of Wicked Heat Pipes

Volume 3 ◽  
2004 ◽  
Author(s):  
R. Kempers ◽  
A. Robinson ◽  
C. Ching ◽  
D. Ewing
Keyword(s):  
Heat Flux ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heat Pipes ◽  
Working Fluid ◽  
Fluid Loading ◽  
Maximum Heat ◽  
Horizontal Orientation ◽  
Maximum Heat Flux ◽  
Dry Out

A study was performed to experimentally characterize the effect of fluid loading on the heat transport performance of wicked heat pipes. In particular, experiments were performed to characterize the performance of heat pipes with insufficient fluid to saturate the wick and excess fluid for a variety of orientations. It was found that excess working fluid in the heat pipe increased the thermal resistance of the heat pipe, but increased maximum heat flux through the pipe in a horizontal orientation. The thermal performance of the heat pipe was reduced when the amount of working fluid was less than required to saturate the wick, but the maximum heat flux through the heat pipe was significantly reduced at all orientations. It was also found in this case the performance of this heat pipe deteriorated once dry-out occurred.

Micro-Scale Two-Phase Flow Heat Transport Device Driven by Electrohydrodynamic Conduction Pumping

2013 ◽  
Author(s):  
Viral K. Patel ◽  
Jamal Seyed-Yagoobi
Keyword(s):  
Heat Transport ◽  
Two Phase Flow ◽  
Operating Conditions ◽  
Electrode Spacing ◽  
Working Fluid ◽  
Phase Flow ◽  
Two Phase ◽  
Micro Scale ◽  
Flow Heat ◽  
Transport Device

Micro-scale two-phase flow heat transport involves specialized devices that are used to remove large amounts of heat from small surface areas. They operate by circulating a working fluid through a heated space which causes phase change from liquid to vapor. During this process, a significant amount of heat is transported away from the heat source. Micro-scale heat transport devices are compact in size and the heat transfer coefficient can be orders of magnitude higher than in macro-scale for similar operating conditions. Thus, it is of interest to develop such devices for cooling of next-generation electronics and other applications with extremely large heat fluxes. The heat transport device presented in this paper is driven by electrohydrodynamic (EHD) conduction pumping. In EHD conduction pumping, when an electric field is applied to a dielectric liquid, flow is induced. The pump is installed in a two-phase flow loop and has a circular 1 mm diameter cross section with electrode spacing on the order of 120 μm. It acts to circulate the fluid in the loop and has a simple yet robust, non-mechanical design. Results from two-phase flow experiments show that it is easily controlled and such electrically driven pumps can effectively be used in heat transport systems.

Analysis of the Evaporating Characteristics of the Grooved Micro Heat Pipe with Alkali Metals as Working Fluid

2012 ◽  
Vol 516-517 ◽  
pp. 84-87 ◽  
Author(s):  
Lei Yu ◽  
Wei Qiang Liu
Keyword(s):  
Thin Film ◽  
Mathematical Model ◽  
Heat Flux ◽  
Heat Pipe ◽  
Alkali Metals ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Working Fluids ◽  
High Temperature Heat Pipe

This paper has built a mathematical model for the evaporating characteristics of the grooved micro heat pipe’s thin film region and computed them in a specific working condition. The evaporating model of Wayner was employed in this mathematical model. The results from computation showed, for the H2O and NH3 as working fluid, at the beginning of the thin film region, the heat flux raised rapidly to a peak value and then declined to almost 0 also rapidly in a very short distance. Differently, for the Na and K as working fluid, the heat flux raised quickly but declined slower. Therefore, the alkali metals working fluids had larger area of high heat flux covered. The results indicated that the alkali metals working fluid has better evaporating characteristics for the high-temperature heat pipe than normal working fluids.

scholarly journals Analysis of the possibility of applications for a two-phase reverse thermosyphon in passive heat transport systems

2018 ◽  
Vol 49 ◽  
pp. 00020 ◽  
Author(s):  
Michal Duda ◽  
Jurij Dobrianski ◽  
Daniel Chludzinski
Keyword(s):  
Heat Transfer ◽  
Heat Source ◽  
Heat Transport ◽  
Heat Load ◽  
Experimental Studies ◽  
Hot Water ◽  
Transport Systems ◽  
Working Fluid ◽  
Two Phase

Devices called reverse thermosyphon enable passive heat transfer when the heat source is above the place of its receipt. This is often the case in solar installations for the preparation of hot water. The article concerns the determination of the possibility of using a two-phase inverted thermosyphon with two working factors in a passive downwards heat transport installation. The analysis was carried out on the basis of previous experimental studies. The height of the tested installation in one case was 1.5 m, in the second 18 m, at a heat load of 300, 600 and 900 W. Water and pentane was used as a working fluid inside the loop. Initial conclusions from the analysis confirm the possibility of using reverse thermosyphon with two working factors in the construction of a passive heat transport system.

Experimental Study of a Two-Phase Heat Transport Device Driven by Electrohydrodynamic Conduction Pumping

2008 ◽  
Author(s):  
Matthew R. Pearson ◽  
Jamal Seyed-Yagoobi
Keyword(s):  
Experimental Study ◽  
Electric Field ◽  
Capillary Pressure ◽  
Heat Transport ◽  
Working Fluid ◽  
Transport Capacity ◽  
Two Phase ◽  
Macro Scale ◽  
Transport Device ◽  
Capillary Phenomenon

Heat pipes are well-known as simple and effective heat transport devices, utilizing two-phase flow and the capillary phenomenon to remove heat. However, the generation of capillary pressure requires a wicking structure and the overall heat transport capacity of the heat pipe is generally limited by the amount of capillary pressure generation that the wicking structure can achieve. Therefore, to increase the heat transport capacity, the capillary phenomenon must be either augmented or replaced by some other pumping technique. Electro-hydrodynamic (EHD) conduction pumping has been demonstrated as an effective method for pumping liquid films by using DC electric fields and a dielectric working fluid. Beyond increased pumping capacity, EHD conduction pumping offers other advantages over capillary pumping, such as active control of the pumping capacity via the intensity of the applied electric field. This experimental study demonstrates the prospects of a macro-scale two-phase heat transport device that is driven by EHD conduction pumping. Various liquid film thicknesses are considered. In each case, the performance of the EHD-driven heat transport device at various electric field intensities is compared to the capabilities of the same device under gravity alone. The effect of tilt on the device is also considered.

Visualization of Two-Phase Flow in 3D Printed Polycarbonate Pulsating Heat Pipe With Aluminum Substrate

2018 ◽  
Author(s):  
Takahiro Arai ◽  
Masahiro Kawaji ◽  
Yasushi Koito
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Two Phase Flow ◽  
Aluminum Plate ◽  
Working Fluid ◽  
Phase Flow ◽  
Pulsating Heat Pipe ◽  
Two Phase ◽  
Flow Channels ◽  
Heat Transport Capability

A pulsating heat pipe (PHP) is a passive device with a good heat transport capability compared to other heat pipes. This paper describes an experimental investigation of a PHP with a serpentine channel fabricated by using a 3-D printer. The configuration of the flow channels in the PHP was close to that of commercially available PHPs made entirely of aluminum. To improve the heat transport capability and enable flow visualization, an aluminum plate was used on one side as the heat-transfer surface, on which transparent flow channels were fabricated by a 3-D printer and a polycarbonate filament. The interface between the aluminum plate and polycarbonate flow channel was cemented with a heat-resistant glue to ensure long term sealing. HFE-7000 was used as a working fluid. Oscillating two-phase flow in the PHP was observed with a high-speed digital video camera and transient surface temperatures at evaporator, insulator and condenser sections were measured by fine diameter thermocouples. The two-phase flow and thermal characteristics of the PHP at different heater power levels are presented.

A Hybrid CFD-Mathematical Model for Simulation of a MEMS Loop Heat Pipe

2004 ◽  
Author(s):  
M. Ghajar ◽  
J. Darabi ◽  
N. Crews
Keyword(s):  
Pressure Drop ◽  
Heat Pipe ◽  
Heat Transport ◽  
Capillary Tube ◽  
Heat Rate ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Two Phase ◽  
Transport Distance ◽  
Compensation Chamber

A Hybrid CFD-Mathematical (HyCoM) model was developed to predict the performance of a Micro Loop Heat Pipe (MLHP) as a function of input heat rate. A micro loop heat pipe is a passive two-phase heat transport device, consisting of microevaporator, microcondenser, micro-compensation chamber (CC), and liquid and vapor lines. A CFD model was incorporated into a loop solver code to identify heat leak to the CC. Two-phase pressure drop in the condenser was calculated by several two phase correlations and results were compared [2]. Capillary tube correlations [3] were used for pressure drop calculations in fluid lines. Effects of working fluid and change in geometry were studied. For a heat transport distance of 10 mm, the base model MLHP was 50mm long, 16mm wide and 1mm thick. In the base model, widths of the grooves, liquid and vapor lines, evaporator, and condenser were 55μm, 200μm, 750μm, 2mm, and 4mm respectively.

Sign in / Sign up

Export Citation Format

Share Document