A Simple Spring-Loaded Inverted Pendulum (SLIP) Model of a Bio-Inspired Quadrupedal Robot Over Compliant Terrains

2018 ◽  
Author(s):  
Hasti Hayati ◽  
Paul Walker ◽  
Terry Brown ◽  
Paul Kennedy ◽  
David Eager
Keyword(s):  
Degrees Of Freedom ◽  
Inverted Pendulum ◽  
Viscoelastic Behavior ◽  
Slip Model ◽  
Runge Kutta Method ◽  
Synthetic Rubber ◽  
Spring Loaded Inverted Pendulum ◽  
Single Support Phase ◽  
The Impact ◽  
Three Degrees Of Freedom

To study the impact of compliant terrains on the biomechanics of rapid legged movements, a well-known spring loaded inverted pendulum (SLIP) model is deployed. The model is a three-degrees-of-freedom system (3 DOF), inspired by galloping greyhounds competing in a racing condition. A single support phase of hind-leg stance in a galloping gait is taken into consideration due to its primary function in powering the greyhounds locomotion and higher rate of musculoskeletal injuries. To obtain and solve the nonlinear second-order differential equation of motions, the Lagrangian method and MATLABb R2017b (ode45 solver), which is based on the Runge-Kutta method, has been used, respectively. To get the viscoelastic behavior of compliant terrains, a Clegg hammer test was developed and performed five times on each sample. The effective spring and damping coefficients of each sample were then determined from the hysteresis curves. The results showed that galloping on the synthetic rubber requires more muscle force compared with wet sand. However, according to the Clegg hammer test, wet sand had a higher impact force than synthetic rubber which can be a risk factor for bone fracture, particularly hock fracture, in greyhounds. The results reported in this paper are not only useful for identifying optimum terrain properties and injury thresholds of an athletic track, but also can be used to design control methods and shock impedances for legged robots performing on compliant terrains.

A Simple Analytical Tool for Legged Robot Design

2012 ◽  
Author(s):  
Zhuohua Shen ◽  
Justin Seipel
Keyword(s):  
Analytical Solutions ◽  
Inverted Pendulum ◽  
Legged Locomotion ◽  
Robot Design ◽  
Slip Model ◽  
Legged Robot ◽  
Biologically Relevant ◽  
Analytical Approximations ◽  
Energy Conserving ◽  
Spring Loaded Inverted Pendulum

Although legged locomotion is better at tackling complicated terrains compared with wheeled locomotion, legged robots are rare, in part, because of the lack of simple design tools. The dynamics governing legged locomotion are generally nonlinear and hybrid (piecewise-continuous) and so require numerical simulation for analysis and are not easily applied to robot designs. During the past decade, a few approximated analytical solutions of Spring-Loaded Inverted Pendulum (SLIP), a canonical model in legged locomotion, have been developed. However, SLIP is energy conserving and cannot predict the dynamical stability of real-world legged locomotion. To develop new analytical tools for legged robot designs, we first analytically solved SLIP in a new way. Then based on SLIP solution, we developed an analytical solution of a hip-actuated Spring-Loaded Inverted Pendulum (hip-actuated-SLIP) model, which is more biologically relevant and stable than the canonical energy conserving SLIP model. The analytical approximations offered here for SLIP and the hip actuated-SLIP solutions compare well with the numerical simulations of each. The analytical solutions presented here are simpler in form than those resulting from existing analytical approximations. The analytical solutions of SLIP and the hip actuated-SLIP can be used as tools for robot design or for generating biological hypotheses.

Stabilized Walking of Humanoid NAO using Enhanced Spring-Loaded Inverted Pendulum Model on Uneven Terrain

2022 ◽  
Vol 13 (1) ◽  
pp. 0-0
Keyword(s):  
Path Length ◽  
Inverted Pendulum ◽  
Center Of Mass ◽  
Humanoid Robots ◽  
Slip Model ◽  
Turning Angle ◽  
Uneven Terrain ◽  
Inverted Pendulum Model ◽  
Pendulum Model ◽  
Spring Loaded Inverted Pendulum

In the coming decades, humanoid robots will play a rising role in society. The present article discusses their walking control and obstacle avoidance on uneven terrain using enhanced spring-loaded inverted pendulum model (ESLIP). The SLIP model is enhanced by tuning it with an adaptive particle swarm optimization (APSO) approach. It helps the humanoid robot to reach closer to the obstacles in order to optimize the turning angle to optimize the path length. The desired trajectory, along with the sensory data, is provided to the SLIP model, which creates compatible COM (center of mass) dynamics for stable walking. This output is fed to APSO as input, which adjusts the placement of the foot during interaction with uneven surfaces and obstacles. It provides an optimum turning angle for shunning the obstacles and ensures the shortest path length. Simulation has been carried out in a 3D simulator based on the proposed controller and SLIP controller in uneven terrain.

Towards Robustly Stable Musculo-Skeletal Simulation of Human Gait: Merging Lumped and Component-Based Modeling Approaches

2012 ◽  
Author(s):  
Justin Seipel
Keyword(s):  
Inverted Pendulum ◽  
Dynamic Models ◽  
Sagittal Plane ◽  
Center Of Mass ◽  
Human Model ◽  
Whole Body ◽  
Human Gait ◽  
Slip Model ◽  
Spring Loaded Inverted Pendulum ◽  
Low Dimensional

The objective of work presented in this paper is to increase the center-of-mass stability of human walking and running in musculo-skeletal simulation. The approach taken is to approximate the whole-body dynamics of the low-dimensional Spring-Loaded Inverted Pendulum (SLIP) model of locomotion in the OpenSim environment using existing OpenSim tools. To more directly relate low-dimensional dynamic models to human simulation, an existing OpenSim human model is first modified to more closely represent bilateral above-knee amputee locomotion with passive prostheses. To increase stability further beyond the energy-conserving SLIP model, an OpenSim model based upon the Clock-Torqued Spring-Loaded-Inverted-Pendulum (CT-SLIP) model of locomotion is also created. The result of this work is that a multi-body musculo-skeletal simulation in Open-Sim can approximate the whole-body sagittal-plane dynamics of the passive SLIP model. By adding a plugin controller to the OpenSim environment, the Clock-Torqued-SLIP dynamics can be approximated in OpenSim. To change between walking and running, only one parameter representing the preferred period of a stride is changed. The result is a robustly stable simulation of the center-of-mass locomotion for both walking and running that could serve as a first step toward increasingly anatomically accurate and robustly stable musculo-skeletal simulations.

scholarly journals Spring-loaded inverted pendulum goes through two contraction-extension cycles during the single-support phase of walking

Biology Open ◽  
2019 ◽  
Vol 8 (6) ◽  
pp. bio043695 ◽  
Author(s):  
Gabriel Antoniak ◽  
Tirthabir Biswas ◽  
Nelson Cortes ◽  
Siddhartha Sikdar ◽  
Chanwoo Chun ◽  
...  
Keyword(s):  
Inverted Pendulum ◽  
Spring Loaded Inverted Pendulum ◽  
Single Support Phase ◽  
Support Phase

DYNAMIC PROPERTIES OF THE ELECTROMECHANICAL SYSTEM DAMPED BY AN IMPACT ELEMENT WITH SOFT STOPS

2014 ◽  
Vol 06 (02) ◽  
pp. 1450016 ◽  
Author(s):  
MAREK LAMPART ◽  
JAROSLAV ZAPOMĚL
Keyword(s):  
Degrees Of Freedom ◽  
Dynamic Properties ◽  
Electric Circuit ◽  
Response Characteristic ◽  
Electromechanical System ◽  
Frequency Response Characteristic ◽  
Impact Element ◽  
The Impact ◽  
The Mathematical Model ◽  
Three Degrees Of Freedom

The main aim of this paper is to focus on analysis of the dynamic properties of the electromechanical system with an impact element. This model is constructed with three degrees of freedom in the mechanical oscillating part, two translational and one rotational, and is completed with an electric circuit. The mathematical model of the system is represented by three mutually coupled second-order ordinary differential equations. Here, the most important nonlinearities are: stiffness of the support spring elements and internal impacts. Several important results were obtained by means of computational simulations. The impacts considerably increase the number of resonance peaks of the frequency response characteristic. Character of the system motion strongly depends on the width of clearances between the impact body and the rotor frame and changes from simple periodic to close to chaotic or to periodic with a large number of ultraharmonic components. For a suitably chosen system parameters, a significant damping effect of the impact element was observed.

scholarly journals THE FORMATION OF PROFESSIONAL TALENT IN DETERMINATION WITH SEMANTIC ATTITUDE TO INNOVATIONS UNDER THE INFLUENCE OF VARIOUS DEGREES OF FREEDOM IN ACTIVITY

2020 ◽  
Vol 17 (4) ◽  
pp. 91-101
Author(s):  
T.N. Soboleva ◽  
Keyword(s):  
Empirical Data ◽  
Degrees Of Freedom ◽  
The Other ◽  
Psychological Analysis ◽  
Other Hand ◽  
Professional Talent ◽  
The One ◽  
The Impact ◽  
Three Degrees Of Freedom

The article is devoted to the poorly studied problem of the formation of talent in the conditions of different degrees of freedom in activity and the impact on that formation of a person’s conservative and innovative semantic attitudes towards the introduction of new equipment. The main objective of the study is to describe how the conditions of different degrees of freedom in the activity are refracted with internal conditions, which are conservative and innovative semantic attitudes and various talent structures. The study was conducted on a sample of 54 qualified railway drivers using a specialized simulator which allows to simulate three degrees of freedom in the activity. The psychological analysis of the activity revealed seven abilities ensuring the implementation of the activity. Based on empirical data, the article shows that low, medium and high degrees of freedom in activity are manifested in different degrees of productivity. Conservative and innovative semantic attitudes to the introduction of new equipment do not have a significant effect on the productivity of the activity in the conditions of different degrees of freedom. Along with this, depending on the conservative and innovative semantic attitudes, different structures of talent in terms of composition and degree of integration under the conditions of different degrees of freedom in the activity are formed. On the one hand, conservative and innovative semantic attitudes act as internal determinants; on the other hand, low, medium and high degrees of freedom in the activity act as external determinants of the formation of various talent structures.

A Spring-Mass Model of Locomotion With Full Asymptotic Stability

2011 ◽  
Author(s):  
Zhuohua Shen ◽  
Justin Seipel
Keyword(s):  
Mass Velocity ◽  
Inverted Pendulum ◽  
Center Of Mass ◽  
Legged Locomotion ◽  
Reduced Model ◽  
Asymptotically Stable ◽  
Slip Model ◽  
Mass Model ◽  
Improved Stability ◽  
Spring Loaded Inverted Pendulum

A reduced model of legged locomotion, called the Spring Loaded Inverted Pendulum (SLIP) has previously been developed to predict the dynamics of locomotion. However, due to energy conservation, the SLIP model can only be partially asymptotically stable in the center-of-mass velocity. The more recently developed Clock-Torqued Spring Loaded Inverted Pendulum (CT-SLIP) model is fully asymptotically stable, and has a significantly larger stability basin than SLIP, but requires more than twice as many parameters. To more completely explore the parameter space and understand the reason for improved stability, we develop and analyze a further reduced model called the Forced-Damped Spring Loaded Inverted Pendulum (FD-SLIP) model.

BIPED HOPPING CONTROL BAzSED ON SPRING LOADED INVERTED PENDULUM MODEL

2010 ◽  
Vol 07 (02) ◽  
pp. 263-280 ◽  
Author(s):  
SEYED HOSSEIN TAMADDONI ◽  
FARID JAFARI ◽  
ALI MEGHDARI ◽  
SAEED SOHRABPOUR
Keyword(s):  
Control Strategy ◽  
Inverted Pendulum ◽  
Hybrid Control ◽  
Sagittal Plane ◽  
Center Of Mass ◽  
Slip Model ◽  
Inverted Pendulum Model ◽  
Wide Range ◽  
Spring Loaded Inverted Pendulum ◽  
Mass Spring

Human running can be stabilized in a wide range of speeds by automatically adjusting muscular properties of leg and torso. It is known that fast locomotion dynamics can be approximated by a spring loaded inverted pendulum (SLIP) system, in which leg is replaced by a single spring connecting body mass to ground. Taking advantage of the inherent stability of SLIP model, a hybrid control strategy is developed that guarantees a stable biped locomotion in sagittal plane. In the presented approach, nonlinear control methods are applied to synchronize the biped dynamics and the spring-mass dynamics. As the biped center of mass follows the mass of the mass-spring model, the whole biped performs a stable locomotion corresponding to SLIP model. Simulations are done to obtain a repeatable hopping for a three-link underactuated biped model. Results show that periodic hopping gaits can be stabilized, and the presented control strategy provides feasible gait trajectories for stance and swing phases.

Foot Contact Interactions of a Clock Torqued Spring-Loaded Inverted Pendulum

2012 ◽  
Author(s):  
Steven Riddle ◽  
Justin Seipel
Keyword(s):  
Disturbance Rejection ◽  
Inverted Pendulum ◽  
Center Of Mass ◽  
Legged Robots ◽  
Contact Friction ◽  
Slip Model ◽  
Specific Interest ◽  
Mass System ◽  
Friction Models ◽  
Spring Loaded Inverted Pendulum

The clock-torqued spring-loaded inverted pendulum (CT-SLIP) model describes the robust dynamic stability properties observed in most animals and some legged robots. However, the model’s behavior is sensitive to changes in liftoff conditions such as those experienced on realistic terrain. Here the incorporation of friction at the foot-ground interface is explored on the CT-SLIP model with specific interest in improving the transient center-of-mass dynamics. Multiple friction models are presented and tuned to reflect a periodic center-of-mass gait. The transient dynamics with friction are analyzed in comparison to the CT-SLIP model and improvements to the settling time and disturbance rejection were found. This addition of foot-ground contact friction may allow for better understanding of center-of-mass system dynamics on realistic terrain.

Sign in / Sign up

Export Citation Format

Share Document