A Numerical Study Into the Influence of Leading Edge Tubercles on the Aerodynamic Performance of a Highly Cambered High Lift Airfoil Wing at Different Reynolds Numbers

2020 ◽  
Author(s):  
Amr Abdelrahman ◽  
Amr Emam ◽  
Ihab Adam ◽  
Hamdy Hassan ◽  
Shinichi Ookawara ◽  
...  
Keyword(s):  
Control Method ◽  
Numerical Study ◽  
Leading Edge ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Passive Flow Control ◽  
Passive Flow ◽  
Stall Angle ◽  
Lifting Surfaces ◽  
Lift And Drag

Abstract Through the last two decades, many studies have demonstrated the ability of leading-edge protrusions (tubercles), inspired from the pectoral flippers of the humpback whale, to be an effective passive flow control method for the stall phase of an airfoil in some cases depending on the geometrical features and the flow regime. Nevertheless, there is a little work associated with revealing tubercles performance for the lifting surfaces with a highly cambered cross-section, used in numerous applications. The present work aims to investigate the effect of implementing leading edge tubercles on the performance of an infinite span rectangular wing with the highly cambered S1223 foil at different flow regimes. Two sets; baseline one and a modified with tubercles have been studied at Re = 0.1 × 106, 0.3 × 106 and 1.5 × 106 using computational fluid dynamics with a validated model. The numerical results demonstrated that Tubercles have the ability to entirely alter the flow structure over the airfoil, confining the separation to troughs, hence, softening the stall characteristics. However, the tubercle modification expedites the presence of the stalled flow over the suction side, lowering the stall angle for the three mentioned Reynolds numbers. While, no considerable difference occurs in lift and drag before the stall.

Experimental Study on the Flow Past Sinusoidal Leading Edge Serrations in a Compressor Cascade

2015 ◽  
Author(s):  
M. S. Rajeshwaran ◽  
Abhijit Kushari
Keyword(s):  
Experimental Study ◽  
Leading Edge ◽  
Suction Side ◽  
Surface Flow ◽  
Compressor Cascade ◽  
Compressor Blades ◽  
Passive Flow Control ◽  
Operational Window ◽  
Compressor Surge ◽  
Stall Angle

The leading edge serrations are a type of passive flow control techniques in a compressor cascade. They are particularly attractive as they have been observed to increase the stall angle. This stall postponing character of the serrations is helpful in preventing compressor surge and widens the operational window of the compressor. Due to the simpler geometry of the serration type used in this study, it can be easily implemented onto the existing compressor blades. An experimental study on the flow modifications and losses due to these serrations are conducted in a linear cascade tunnel. The experiments are conducted on blades of NACA 65209 airfoil with and without leading edge serrations at Re of 120,000. Four serration profiles of various width and amplitude are compared. End plane measurements taken with 5-hole probe are studied for the better serration profile and surface flow visualizations are conducted to study the variation in the surface flow pattern on the suction side. The surface flow visualization reveals the presence of local recirculation zones and stream wise vortices created from each wave of the serration leading to flow attachment. These serrated blades have higher losses at 0 deg incidence; the reason for the same is found to be the flat leading edge surfaces formed from serration.

Experimental and Numerical Study of Impingement on an Airfoil Leading Edge With and Without Showerhead and Gill Film Holes

2005 ◽  
Vol 128 (2) ◽  
pp. 310-320 ◽  
Author(s):  
M. E. Taslim ◽  
A. Khanicheh
Keyword(s):  
Heat Transfer ◽  
Turbulence Modeling ◽  
Numerical Study ◽  
Leading Edge ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Numerical Predictions ◽  
Impingement Heat Transfer

This experimental investigation deals with impingement on the leading edge of an airfoil with and without showerhead film holes and its effects on heat transfer coefficients on the airfoil nose area as well as the pressure and suction side areas. a comparison between the experimental and numerical results are also made. the tests were run for a range of flow conditions pertinent to common practice and at an elevated range of jet Reynolds numbers (8000–48,000). The major conclusions of this study were: (a) The presence of showerhead film holes along the leading edge enhances the internal impingement heat transfer coefficients significantly, and (b) while the numerical predictions of impingement heat transfer coefficients for the no-showerhead case were in good agreement with the measured values, the case with showerhead flow was under-predicted by as much as 30% indicating a need for a more elaborate turbulence modeling.

Separation Control by Slot Jet in a Critically Loaded Compressor Cascade

2018 ◽  
Vol 35 (3) ◽  
pp. 229-239 ◽  
Author(s):  
Jiaguo Hu ◽  
Rugen Wang ◽  
Peigen Wu ◽  
Chen He
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Suction Side ◽  
Jet Flow ◽  
Compressor Cascade ◽  
Control Effect ◽  
Passive Flow Control ◽  
Passive Flow ◽  
Flow Loss ◽  
Great Pressure

Abstract Separation in compressor cascade triggers flow loss and instability. This paper presents a passive flow control method by introducing a slot into the blade. The slot induces self-adapted jet, while the jet flow is used to suppress cascade’s separation. To study the flow control effect, experiments were conducted and flow field details were given by validated numerical simulations. The results show that a well-designed slot carries adequate jet airflow from pressure side (PS) to suction side (SS) due to the great pressure fall between the two sides. The jet airflow delays suction side separation within specific incidence angles, so the performance of cascade achieves considerable improvements. It enables to be concluded that the slot carries jet flow to SS separation zone, and then the self-adapted jet flow re-energizes low momentum fluid and suppresses vortices in the separation which are negative to the cascade flow.

Experimental and Numerical Study of Impingement on an Airfoil Leading-Edge With and Without Showerhead and Gill Film Holes

2005 ◽  
Author(s):  
M. E. Taslim ◽  
A. Khanicheh
Keyword(s):  
Heat Transfer ◽  
Turbulence Modeling ◽  
Numerical Study ◽  
Leading Edge ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Numerical Predictions ◽  
Impingement Heat Transfer

This experimental investigation deals with impingement on the leading-edge of an airfoil with and without showerhead film holes and its effects on heat transfer coefficients on the airfoil nose area as well as the pressure and suction side areas. A comparison between the experimental and numerical results are also made. The tests were run for a range of flow conditions pertinent to common practice and at an elevated range of jet Reynolds numbers (8000–48000). The major conclusions of this study were: a) the presence of showerhead film holes along the leading edge enhances the internal impingement heat transfer coefficients significantly, and b) while the numerical predictions of impingement heat transfer coefficients for the no-showerhead case were in good agreement with the measured values, the case with showerhead flow was underpredicted by as much as 30% indicating a need for a more elaborate turbulence modeling.

Influence of Leading Edge Tubercles in an Annular Compressor Cascade With Different Hub-Tip Ratios and Aspect Ratios

2017 ◽  
Author(s):  
Tan Zheng ◽  
Mingmin Zhu ◽  
Xiaoqing Qiang ◽  
Jinfang Teng ◽  
Jinzhang Feng
Keyword(s):  
Numerical Study ◽  
Incidence Angle ◽  
Leading Edge ◽  
Compressor Cascade ◽  
Corner Separation ◽  
Low Speed ◽  
Passive Flow Control ◽  
Passive Flow ◽  
Aspect Ratios ◽  
Flow Visualizations

Humpback whale flippers’ scalloped tubercles on the leading edge are thought to enhance the whale’s underwater maneuverability. Inspired by the flippers, leading edge tubercles are applied in a low speed annular compressor cascade as a type of passive flow control techniques in this paper. A numerical study is performed to investigate the influence of tubercles on the aerodynamic losses and corner separation in the low speed cascades. Different low speed cascades based on a CDA airfoil profile are built with several hub-tip ratios and aspect ratios. Steady RANS simulations are carried out for these cascades with and without leading edge tubercles. The aerodynamic performance and corner separation features are subsequently investigated in these cascades. The influence of tubercles under the variation of hub-tip ratio and aspect ratio is understood and concluded from the comparison of the performance attained by different cascades. Flow visualizations at a post-stall incidence angle show that the interaction between the tubercle-induced streamwise vortices and corner separation vortices plays a crucial role in attenuating the corner separation and reducing losses. By combining the performance analysis and flow visualizations, this paper discusses the mechanism of leading edge tubercles in a low speed annular compressor cascade with different hub-tip ratios and aspect ratios.

scholarly journals Centrifugal Compressor Stall Control by the Application of Engineered Surface Roughness on Diffuser Shroud Using Numerical Simulations

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2033
Author(s):  
Amjid Khan ◽  
Muhammad Irfan ◽  
Usama Muhammad Niazi ◽  
Imran Shah ◽  
Stanislaw Legutko ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Control Method ◽  
Flow Instability ◽  
Passive Flow Control ◽  
Passive Flow ◽  
Low Mass

Downsizing in engine size is pushing the automotive industry to operate compressors at low mass flow rate. However, the operation of turbocharger centrifugal compressor at low mass flow rate leads to fluid flow instabilities such as stall. To reduce flow instability, surface roughness is employed as a passive flow control method. This paper evaluates the effect of surface roughness on a turbocharger centrifugal compressor performance. A realistic validation of SRV2-O compressor stage designed and developed by German Aerospace Center (DLR) is achieved from comparison with the experimental data. In the first part, numerical simulations have been performed from stall to choke to study the overall performance variation at design conditions: 2.55 kg/s mass flow rate and rotational speed of 50,000 rpm. In second part, surface roughness of magnitude range 0–200 μm has been applied on the diffuser shroud to control flow instability. It was found that completely rough regime showed effective quantitative results in controlling stall phenomena, which results in increases of operating range from 16% to 18% and stall margin from 5.62% to 7.98%. Surface roughness as a passive flow control method to reduce flow instability in the diffuser section is the novelty of this research. Keeping in view the effects of surface roughness, it will help the turbocharger manufacturers to reduce the flow instabilities in the compressor with ease and improve the overall performance.

scholarly journals Numerical Study of Sediment Erosion Analysis in Francis Turbine

2019 ◽  
Vol 11 (5) ◽  
pp. 1423 ◽  
Author(s):  
Md Rakibuzzaman ◽  
Hyoung-Ho Kim ◽  
Kyungwuk Kim ◽  
Sang-Ho Suh ◽  
Kyung Kim
Keyword(s):  
Erosion Rate ◽  
Cavitation Erosion ◽  
Numerical Study ◽  
Leading Edge ◽  
Suction Side ◽  
Hydraulic Turbine ◽  
Francis Turbine ◽  
Trailing Edge ◽  
Sand Erosion ◽  
Turbine Design

Effective hydraulic turbine design prevents sediment and cavitation erosion from impacting the performance and reliability of the machine. Using computational fluid dynamics (CFD) techniques, this study investigated the performance characteristics of sediment and cavitation erosion on a hydraulic Francis turbine by ANSYS-CFX software. For the erosion rate calculation, the particle trajectory Tabakoff–Grant erosion model was used. To predict the cavitation characteristics, the study’s source term for interphase mass transfer was the Rayleigh–Plesset cavitation model. The experimental data acquired by this study were used to validate the existing evaluations of the Francis turbine. Hydraulic results revealed that the maximum difference was only 0.958% compared with the CFD data, and 0.547% compared with the experiment (Korea Institute of Machinery and Materials (KIMM)). The turbine blade region was affected by the erosion rate at the trailing edge because of their high velocity. Furthermore, in the cavitation–erosion simulation, it was observed that abrasion propagation began from the pressure side of the leading edge and continued along to the trailing edge of the runner. Additionally, as sediment flow rates grew within the area of the attached cavitation, they increased from the trailing edge at the suction side, and efficiency was reduced. Cavitation–sand erosion results then revealed a higher erosion rate than of those of the sand erosion condition.

Study of three types of wave leading edge on the performance of industrial turbine blade cascade

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Hamed Ghandi ◽  
Reza Aghaei Togh ◽  
Abolghasem Mesgarpoor Tousi
Keyword(s):  
Turbine Blade ◽  
Flow Separation ◽  
Numerical Solutions ◽  
Incidence Angle ◽  
Leading Edge ◽  
Content Type ◽  
Passive Flow Control ◽  
Passive Flow ◽  
Geometrical Features ◽  
Control Methodology

Purpose The blade profile and its geometrical features play an important role in the separation of the boundary layer on the blade. Modifying the blade geometry, which might lead to the delay or elimination of the flow separation, can be considered as a passive flow control methodology. This study aims to find a novel and inexpensive way to reduce loss with appropriate modifications on the leading edge of the turbine blade. Design/methodology/approach Three types of wave leading edges were designed with different wavelengths and amplitudes. The selected numbers for the wave characteristics were based on the best results of previous studies. Models with appropriate and independent meshing have been simulated and studied by a commercial software. The distribution of the loss at different planes and mid-plane velocity vectors were shown. The mass flow average of loss at different incidence angles was calculated for the reference blade and modified ones for the sake of comparison. Findings The results show that in all three types of modified blades compared to the reference blade, the elimination of flow separation is observed and therefore the reduction of loss at the critical incidence angle of I = –15°. As the amplitude of the wave increased, the amount of loss growing up, while the increase in wavelength caused the loss to decrease. Originality/value The results of the present numerical analysis were validated by the laboratory results of the reference blade. The experimental study of modified blades can be used to quantify numerical solutions.

Sign in / Sign up

Export Citation Format

Share Document