Hydrodynamic Study on the Damping Characteristics of Cylindrical FPSO With the Heave Plate

2020 ◽  
Author(s):  
Meirong Jiang ◽  
Da Li ◽  
Zhongchang Wang ◽  
Xu Jia ◽  
Yang Yu
Keyword(s):  
Model Test ◽  
Hydrodynamic Model ◽  
Damping Ratio ◽  
Hydrodynamic Performance ◽  
Damping Coefficient ◽  
Natural Period ◽  
Damping Characteristics ◽  
Hydrodynamic Study ◽  
Heave Plate ◽  
Motion Amplitude

Abstract The heave plate setting up on the hull can effectively improve the movement performance of the cylindrical FPSO. In the research process of its damping effect, a reliable model is also needed to do the further study besides the physical model test. The objective of the present work is to establish a reasonable hydrodynamic model to investigate the damping behavior of the cylindrical FPSO with the heave plate. Based on the k-ε turbulence model and the VOF method, a three-dimensional hydrodynamic model are established to simulate the movement of the cylindrical FPSO in the offshore environment. A typical annular thin plate is set up on the bottom side of the hull as the damping structure. The available experimental data are adopted to preliminarily verify the established model. The structural pattern of the damping plate is optimized considering different widths of the plate and excitation modes. The motion amplitude, natural period and damping coefficient can be extracted from the computation and be analyzed to obtain the hydrodynamic performance of the cylindrical FPSO. From the simulation and verification, the numerical results are agreed quite well with the measured values in the model test, which proves that the model is reliable. When the cylindrical FPSO oscillates in the water body, the vortexes are generated around the heave plate and shed from it, which are the primary reason for the increase of the viscous damping. As the width of the heave plate increases, the damping coefficient and ratio increase gradually, but the natural period of the structure is basically unchanged. As for the amplitude of the motion, the variation of the damping coefficient is not obvious, and the natural period of the structure is also basically unchanged. When the motion amplitude is relatively small, the damping ratio increases gradually with the increase of the motion amplitude; while the motion amplitude is large, the amplitude increment of damping ratio tends to be flat, or even decreases. This hydrodynamic study is meaningful for the researcher and engineer to further understand the damping characteristics of the cylindrical FPSO. It can also provide some technical supports for the structural optimization design of the heave plate.

The Effect of Dual-Rate Suspension Damping on Vehicle Response to Transient Road Inputs

2009 ◽  
Vol 131 (1) ◽  
Author(s):  
T. P. Waters ◽  
Y. Hyun ◽  
M. J. Brennan
Keyword(s):  
Damping Ratio ◽  
Peak Acceleration ◽  
Acceleration Response ◽  
Natural Period ◽  
Single Degree Of Freedom ◽  
Vehicle Suspensions ◽  
Damping Characteristics ◽  
Potential Benefits ◽  
Approximate Expressions

The acceleration response of road vehicles to shock inputs from road irregularities such as bumps and hollows is an important consideration in the design of vehicle suspensions and damping characteristics, in particular. In this paper, the influence of the damper on the shock response of a simple vehicle model is considered. An analysis is presented of a single degree-of-freedom model subjected to a transient displacement input. Simple approximate expressions are given for the peak acceleration during an impulse of both short and long durations compared to the natural period, from which the role of the damper is clearly apparent. For impulses of short duration the peak acceleration occurs during the impulse and is shown to be approximately proportional to the damping ratio. Corollary to this, the peak acceleration can be reduced by switching the damper to a lower value during the impulse. The potential benefits of doing so are illustrated through numerical simulation, and a simple formula is given for the maximum possible reduction in peak acceleration. The results are also contrasted with those of a conventional dual-rate automotive damper model. The switchable damper is found to offer sufficient benefit to warrant further investigation.

UJI TARIK HIDRODINAMIKMODEL KAPAL BERSAYAP WiSE DENGAN LAMBUNG DASAR BERSTEP

2013 ◽  
Vol 12 (3) ◽  
Author(s):  
Iskendar Iskendar ◽  
Andi Jamaludin ◽  
Paulus Indiyono
Keyword(s):  
Comparative Study ◽  
Model Test ◽  
Hydrodynamic Model ◽  
Surface Effect ◽  
Center Of Gravity ◽  
Test Results ◽  
Flat Bottom ◽  
Towing Tank ◽  
Test Models ◽  
Wetted Surface Area

This paper describes hydrodynamic model tests of Wing in Surface Effect (WiSE) Craft. These craft  was fitted with  stephull  form in different location on longitudinal flat bottom (stepedhull planning craft) to determine the influences of sticking and porpoising motion performances. These motions are usually occured when the craft start to take-off from water surfaces. The test models with scale of 1 : 7 were comprised of 4 (four) stephull models and 1 (one) non-stephull model  as a comparative study. The hydrodynamic  tests were performed with craft speed of 16 – 32 knots (prototype values) in Towing Tank at UPT. Balai Pengkajian dan Penelitian Hidrodinamika (BPPH), BPPT, Surabaya. The resistance (drag) was measured by dynamo meter and the trim of model (draft changing at fore and aft  of model due to model speed) was measured by trim meter. By knowing the value of model trim, the wetted surface area can be determined. Then, the lift forces were calculated based on these measured values. The model test results were presented on tables and curves.  Test results show that models  with step located far away from center of gravity of the WiSE craft tend to porpoising and sticking condition, except if the step location on the below of these center of gravity. While model without step tends to sticking conditions.

The Influence of Support Hardware and Piping System Seismic Response on Snubber Support Damping

1997 ◽  
Vol 119 (4) ◽  
pp. 451-456 ◽  
Author(s):  
C. Lay ◽  
O. A. Abu-Yasein ◽  
M. A. Pickett ◽  
J. Madia ◽  
S. K. Sinha
Keyword(s):  
Seismic Response ◽  
Fundamental Frequency ◽  
Damping Ratio ◽  
Damping Coefficient ◽  
Piping System ◽  
Nodal Displacement ◽  
Damping Coefficients ◽  
Fundamental Frequencies ◽  
Piping Systems

The damping coefficients and ratios of piping system snubber supports were found to vary logarithmically with pipe support nodal displacement. For piping systems with fundamental frequencies in the range of 0.6 to 6.6 Hz, the support damping ratio for snubber supports was found to increase with increasing fundamental frequency. For 3-kip snubbers, damping coefficient and damping ratio decreased logarithmically with nodal displacement, indicating that the 3-kip snubbers studied behaved essentially as coulomb dampers; while for the 10-kip snubbers studied, damping coefficient and damping ratio increased logarithmically with nodal displacement.

Preparation and Vibration Damping Characteristics of Wide Frequency Domain PVMQ/IIR Foam Materials

2012 ◽  
Vol 538-541 ◽  
pp. 2298-2303
Author(s):  
Shi Kai Luo ◽  
Guo Fang Ding ◽  
Jing Li Li ◽  
Yan Song Sha ◽  
Qing Min Cheng ◽  
...  
Keyword(s):  
Frequency Domain ◽  
Wide Temperature Range ◽  
Damping Ratio ◽  
Vibration Damping ◽  
Simple Equation ◽  
Structural Damping ◽  
Damping Characteristics ◽  
Damping Materials ◽  
Foaming Technology ◽  
Isoprene Rubber

In this paper, we prepared foaming silicon rubber (PVMQ) /isobutylene-isoprene rubber (IIR) composites with chemical foaming technology. The DMA tests results showed that these foaming materials have effective damping characteristics in a wide temperature range. With the special vibrator, we found that the PVMQ/IIR foams that we prepared were the damping materials which has wide frequency domain, because they can keep high damping ratio in a wide frequency domain. When the preloading was between 1.0 mm and 1.7 mm, the structural damping did not change obviously. According to tests, we found that the damping ratio of these foams was fit to the simple equation .

Development and Verification of Modeling Practice for CFD Decay Calculations to Obtain Roll Damping of FPSO

2021 ◽  
Author(s):  
Arjen Koop ◽  
Pierre Crepier ◽  
Sebastien Loubeyre ◽  
Corentin Dobral ◽  
Kai Yu ◽  
...  
Keyword(s):  
Model Test ◽  
Test Results ◽  
Cfd Modelling ◽  
Roll Damping ◽  
Natural Period ◽  
Computational Mesh ◽  
Safety Studies ◽  
Offshore Industry ◽  
Decay Tests ◽  
Set Up

Abstract Estimates for roll damping are important input parameters for simulation studies on vessels operating at sea, e.g. FPSO mooring in waves, wind and current, workability and operability investigations, Dynamic Position studies, ship-to-ship operations and safety studies of vessels. To accurately predict the motions of vessels this quantity should be determined with confidence in the values. Traditionally, model experiments in water basins using so-called decay tests are carried out to determine the roll damping. With recent advancements in CFD modelling, the offshore industry has started using CFD as an alternative tool to compute the roll damping of FPSO’s. In order to help adopt CFD as a widely accepted tool, there is a need to develop confidence in CFD predictions. Therefore, a practical CFD modelling practice is developed within the Reproducible CFD JIP for roll decay CFD simulations. The Modelling Practice describes the geometry modelling, computational mesh, model set-up and post-processing for these type of CFD calculations. This modelling practice is verified and validated by three independent verifiers against available model test data. This paper provides an overview of the developed modelling practice and the calculated CFD results from the verifiers. The CFD modelling practice is benchmarked against available model test results for a tanker-shaped FPSO. By following this modelling practice, the CFD predictions for the equivalent linear damping coefficient and natural period of the roll motions are within 10% for all verifiers and within 10% from the model test results. Therefore, we conclude that when following the developed modelling practice for roll decay simulations, reliable, accurate and reproducible results can be obtained for the roll damping of tanker-shaped FPSOs.

Analysis of Beam-Like Structures With Displacement-Dependent Friction Forces: Part I — Single-Degree-of-Freedom Model

1995 ◽  
Author(s):  
Wayne E. Whiteman ◽  
Aldo A. Ferri
Keyword(s):  
Dry Friction ◽  
Damping Ratio ◽  
Strong Dependence ◽  
Time Integration ◽  
Single Mode ◽  
Stick Slip ◽  
Friction Forces ◽  
Equivalent Damping ◽  
Damping Characteristics ◽  
Parameter Values

Abstract The dynamic behavior of a beam-like structure undergoing transverse vibration and subjected to a displacement-dependent dry friction force is examined. In Part I, the beam is modeled by a single mode while Part II considers multi-mode representations. The displacement dependence in each case is caused by a ramp configuration that allows the normal force across the sliding interface to increase linearly with slip displacement. The system is studied first by using first-order harmonic balance and then by using a time integration method. The stick-slip behavior of the system is also studied. Even though the only source of damping is dry friction, the system is seen to exhibit “viscous-like” damping characteristics. A strong dependence of the equivalent natural frequency and damping ratio on the displacement amplitude is an interesting result. It is shown that for a given set of parameter values, an optimal ramp angle exists that maximizes the equivalent damping ratio. The appearance of two dynamic response solutions at certain system and forcing parameter values is also seen. Results suggest that the overall characteristics of mechanical systems may be improved by properly configuring frictional interfaces to allow normal forces to vary with displacement.

Enhancement of vibration characteristics in filament wound FRP composite shafts using nitinol wires

2018 ◽  
Vol 47 (5) ◽  
pp. 377-385 ◽  
Author(s):  
Kannan Murugesan ◽  
Kalaichelvan K. ◽  
M.P. Jenarthanan ◽  
Sornakumar T.
Keyword(s):  
Natural Frequency ◽  
Damping Ratio ◽  
Filament Winding ◽  
Fiber Reinforced ◽  
Content Type ◽  
Fiber Reinforced Plastic ◽  
Damping Characteristics ◽  
Filament Wound ◽  
Reinforced Plastic ◽  
Hollow Shafts

Purpose The purpose of this paper is to investigate the use of embedded Shape Memory Alloy (SMA) nitinol wire for the enhancement of vibration and damping characteristics of filament-wound fiber-reinforced plastic composite hollow shafts. Design/methodology/approach The plain Glass Fiber-Reinforced Plastic (GFRP) and plain Carbon Fiber-Reinforced Plastic (CFRP) hollow shafts were manufactured by filament winding technique. Experimental modal analysis was conducted for plain hollow shafts of C1045 steel, GFRP and CFRP by subjecting them to flexural vibrations as per ASTM standard C747, with both ends clamped (C-C) end condition to investigate their vibration and damping behavior in terms of first natural frequency, damping time and damping ratio. Nitinol wires pre-stressed at various pre-strains (2, 4 and 6 per cent) were embedded with CFRP hollow shafts following same manufacturing technique, and similar experimental modal analysis was carried out by activating nitinol wires. The first natural frequencies of all the shaft materials were also predicted theoretically and compared with experimental measurements. Findings Among the three materials C1045 steel, plain GFRP and plain CFRP, the vibration and damping behavior were found to be the best for plain CFRP. Hence, CFRP shafts were considered for further improvement by embedding nitinol wires at pre-stressed condition. For CFRP shafts embedded with nitinol wires, the damping time decreased; and damping ratio and first natural frequency increased with increase in percentage of pre-strain. In comparison with plain CFRP, 7 per cent increase in first natural frequency and 100 per cent increase in damping ratio were observed for nitinol embedded CFRP shafts with 6 per cent pre-strain. Theoretical predictions of the first natural frequencies agree well with the experimental results for all the shaft materials. Originality/value The effect of nitinol on vibration and damping characteristics of filament wound hollow CFRP composite shafts with different pre-strains has not been studied extensively by the previous researchers. This paper addresses the effect of embedded nitinol wires pre-stressed at three varied pre-strains, that is, 2, 4 and 6 per cent on the vibration and damping characteristics of composite hollow CFRP shafts manufactured by filament winding technique.

scholarly journals An investigation into the mechanical damping characteristics of catenary contact wires and their effect on aerodynamic galloping instability

2003 ◽  
Vol 217 (2) ◽  
pp. 63-71 ◽  
Author(s):  
M. T. Stickland ◽  
T. J. Scanlon ◽  
I. A. Craighead ◽  
J Fernandez
Keyword(s):  
Wind Speed ◽  
East Coast ◽  
Damping Ratio ◽  
Friction Damper ◽  
Wind Speeds ◽  
Damping Characteristics ◽  
Damped Oscillation ◽  
Mechanical Damping ◽  
The Uk ◽  
Wire System

Measurement of the damped oscillation of a section of the UK East Coast Main Line (ECML) catenary/contact wire system was undertaken, and the natural frequency and mechanical damping were found to be 1.4Hz and 0.05 respectively. This information was used to assess the effect of increasing the mechanical damping ratio on the susceptibility of the system to an aerodynamic galloping instability. The section of line tested was known to gallop at wind speeds of approximately 40 mile/h, and theoretical and experimental work verified this. A friction damper arm was designed and three units were fitted to the section of line affected. The introduction of increased mechanical damping was found to raise the mechanical damping coefficient of the line to between 0.095 and 0.18, and the mathematical analysis produced a theoretical wind speed for galloping oscillation of between 75 and 141 mile/h respectively. For over a year since the units were fitted, no problems with galloping instability have been observed.

Experimental Investigation on Damping Characteristics in Pump-Sand Box-Isolation System

2014 ◽  
Vol 1051 ◽  
pp. 906-909
Author(s):  
Xiang Jun Kong ◽  
Chong Zheng Chen
Keyword(s):  
Particle Size ◽  
Vibration Isolation ◽  
Influence Factor ◽  
Damping Ratio ◽  
Particle Packing ◽  
Initial Displacement ◽  
Isolation System ◽  
Damping Characteristics ◽  
Sand Box ◽  
Particle Damping

Sand is used in the pump-sand box-isolation system, studying the initial displacement, particle size and packing rate how to affect the damping ratio by free vibration experiments. The result shows that the initial displacement of the system has less effect on damping ratio, the particle packing rate is a significant influence factor of damping ratio, selecting the appropriate particle packing rate can get the maximum damping ratio, reducing the particle size can increase the system damping ratio, but the damping ratio no longer obviously changes when the particle size of is less than 1.5mm. In general, the packing rate needs to be controlled at below 70% in metal spring or rubber isolator system. This result can provide the basis for the design of particle damping vibration isolation system.

Free Vibration Test for Damping Characteristics of Hybrid Polyester Matrix Composite with Carbon Particles

2016 ◽  
Vol 11 ◽  
pp. 1-6
Author(s):  
K. Karthik ◽  
R. Rohith Renish ◽  
I. Irfan Ahmed ◽  
T. Niruban Projoth
Keyword(s):  
Free Vibration ◽  
Hybrid Composites ◽  
Glass Fibers ◽  
Damping Ratio ◽  
Mode Shapes ◽  
Vibration Test ◽  
Engineering Structures ◽  
Carbon Filler ◽  
Damping Characteristics ◽  
Free Vibration Test

In this research aims to study the damping characteristics of hybrid polymer composite, which can be used in engineering structures and in many other applications. Hybrid composites are namely Glass fiber and carbon filler reinforced with polyester and epoxy matrix have been prepared by vacuum bag molding fabrication technique. Then the free vibration test were conducted using FFT analyzer with Lab VIEW software. The damping ratio and natural frequency were investigated for fabricated composites. Then through ANSYS, the mode shapes and natural frequencies were determined and the results were compared with experimental results. The damping ratio increases with increased volume fractions of E-glass fibers for both the types of polymer composites. Vibrations are concerned to large structures such as aircraft, as well as small structures such as electronic equipments.

Sign in / Sign up

Export Citation Format

Share Document