scholarly journals A New Electrical Circuit With Negative Capacitances to Enhance Resistive Shunt Damping

2015 ◽  
Author(s):  
Marta Berardengo ◽  
Stefano Manzoni ◽  
Olivier Thomas ◽  
Christophe Giraud-Audine
Keyword(s):  
Electromechanical Coupling ◽  
Short Circuit ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Open Circuit ◽  
Electrical Circuit ◽  
Structural Vibration ◽  
Electrical Network ◽  
Negative Capacitance ◽  
Shunt Damping

This article proposes a new layout of electrical network based on two negative capacitance circuits, aimed at increasing the performances of a traditional resistive piezoelectric shunt for structural vibration reduction. It is equivalent to artificially increase the modal electromechanical coupling factor of the electromechanical structure by both decreasing the short-circuit natural frequencies and increasing the open-circuit ones. This leads to higher values of the modal electromechanical coupling factor with respect to simple negative capacitance configurations, when the same margin from stability is considered. This technique is shown to be powerful in enhancing the control performance when associated to a simple resistive shunt, usually avoided because of its poor performances.

scholarly journals Electrothermal Phenomena in Ferroelectrics

Actuators ◽  
2020 ◽  
Vol 9 (4) ◽  
pp. 93
Author(s):  
Kenji Uchino
Keyword(s):  
Thermal Diffusivity ◽  
Lead Zirconate Titanate ◽  
Electromechanical Coupling ◽  
Short Circuit ◽  
Electromechanical Coupling Factor ◽  
Lead Zirconate ◽  
Coupling Factor ◽  
Open Circuit ◽  
Comprehensive Knowledge ◽  
Poling Direction

Physical properties of lead-zirconate-titanate (PZT) ceramics change according to the initial electric poling process and electrical boundary conditions. This paper reports the electrothermal, piezothermal, and piezoelectric coupling phenomena in ferroelectrics from thermodynamics viewpoints, in particular, thermal property differences between unpoled and poled PZT’s in the poling direction for open circuit and short circuit conditions. We propose a new terminology, “secondary electrothermal” coupling factor kλ, which is analogous to the electromechanical coupling factor k, relating the elastic compliances under short- and open-circuit conditions, in order to explain the fact that the short-circuit condition exhibited the larger thermal diffusivity than the open-circuit condition. On the other hand, the unpoled specimen exhibits the lowest thermal diffusivity. This tutorial paper was authored for providing comprehensive knowledge on equilibrium and time-dependent thermodynamics in ferroelectrics.

Thermal Conductivities of PZT Piezoelectric Ceramics under Different Electrical Boundary Conditions

2020 ◽  
Vol 3 (1) ◽  
pp. 10
Author(s):  
Husain N.  Shekhan ◽  
Erkan A.  Gurdal ◽  
Lalitha Ganapatibhotla ◽  
Janna K.  Maranas ◽  
Ron Staut ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Boundary Conditions ◽  
Lead Zirconate Titanate ◽  
Electromechanical Coupling ◽  
Short Circuit ◽  
Coupling Factor ◽  
Open Circuit ◽  
Electrical Boundary Conditions ◽  
Poling Direction

<p>Physical properties of polycrystalline lead-zirconate-titanate (PZT) changes according to electrical boundary conditions and poling. This paper reports the thermal properties of poled and unpoled PZT's in the poling direction for open circuit and short circuit conditions. The authors found that the short-circuit condition exhibited the largest thermal conductivity than the open-circuit condition. In the relationship between these two thermal properties, the authors propose the "electrothermal" coupling factor k<sup>κ</sup><sub>33</sub>, which is similar to the electromechanical coupling factor k<sub>33</sub> relating the elastic compliances under short- and open-circuit conditions. On the other hand, the thermal conductivity of the unpoled specimen exhibits the lowest thermal conductivity, in comparison with the poled specimens, which suggests the importance of phonon mode scattering on the thermal conductivity with respect to elastic compliance.</p>

scholarly journals Design and Analysis of a Novel Piezoceramic Stack-based Smart Aggregate

Sensors ◽  
2020 ◽  
Vol 20 (22) ◽  
pp. 6438
Author(s):  
Guangtao Lu ◽  
Xin Zhu ◽  
Tao Wang ◽  
Zhiqiang Hao ◽  
Bohai Tan
Keyword(s):  
Resonance Frequency ◽  
Electromechanical Coupling ◽  
Structural Parameters ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Stress Waves ◽  
Parallel Connection ◽  
Smart Aggregate ◽  
In Series ◽  
Piezoelectric Wafers

A novel piezoceramic stack-based smart aggregate (PiSSA) with piezoceramic wafers in series or parallel connection is developed to increase the efficiency and output performance over the conventional smart aggregate with only one piezoelectric patch. Due to the improvement, PiSSA is suitable for situations where the stress waves easily attenuate. In PiSSA, the piezoelectric wafers are electrically connected in series or parallel, and three types of piezoelectric wafers with different electrode patterns are designed for easy connection. Based on the theory of piezo-elasticity, a simplified one-dimensional model is derived to study the electromechanical, transmitting and sensing performance of PiSSAs with the wafers in series and parallel connection, and the model was verified by experiments. The theoretical results reveal that the first resonance frequency of PiSSAs in series and parallel decreases as the number or thickness of the PZT wafers increases, and the first electromechanical coupling factor increases firstly and then decrease gradually as the number or thickness increases. The results also show that both the first resonance frequency and the first electromechanical coupling factor of PiSSA in series and parallel change no more than 0.87% as the Young’s modulus of the epoxy increases from 0.5 to 1.5 times 3.2 GPa, which is helpful for the fabrication of PiSSAs. In addition, the displacement output of PiSSAs in parallel is about 2.18–22.49 times that in series at 1–50 kHz, while the voltage output of PiSSAs in parallel is much less than that in parallel, which indicates that PiSSA in parallel is much more suitable for working as an actuator to excite stress waves and PiSSA in series is suitable for working as a sensor to detect the waves. All the results demonstrate that the connecting type, number and thickness of the PZT wafers should be carefully selected to increase the efficiency and output of PiSSA actuators and sensors. This study contributes to providing a method to investigate the characteristics and optimize the structural parameters of the proposed PiSSAs.

Piezoelectric Shear Mode Inkjet Actuator

2001 ◽  
Vol 687 ◽  
Author(s):  
Jürgen Brünahl ◽  
Alex M. Grishin ◽  
Sergey I. Khartsev ◽  
Carl Österberg
Keyword(s):  
Electromechanical Coupling ◽  
Microelectromechanical Systems ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Shear Mode ◽  
Drop On Demand ◽  
Ink Jet ◽  
Ferroelectric Hysteresis ◽  
Comprehensive Characterization

AbstractWe report on comprehensive characterization of piezoelectric shear mode inkjet actuators micromachined into bulk Pb(Zr0.53Ti0.47)O3 (PZT) ceramics. The paper starts with an overview of different inkjet technologies such as continuous jet and drop-on-demand systems, whereat main attention is turned on piezoelectric systems particularly Xaar-type shear mode inkjet color printheads. They are an example of complex microelectromechanical systems (MEMS) and comprise a ferroelectric array of 128 active ink channels (75νm wide and 360νm deep). Detailed information about manufacturing and principles of operation are given. Several techniques to control manufacturing processes and to characterize properties of the piezoelectric material are described: dielectric spectroscopy to measure dielectric permittivity ε and loss tanσ; ferroelectric hysteresis P-E loop tracing to get remnant polarization Pr and coercive field Ec, and a novel pulsed technique to quantify functional properties of the PZT actuator such as acoustic resonant frequencies and electromechanical coupling factor. Stroboscope technique has been employed to find correlation between the degradation of ink-jet performance and heat/high voltage treatment resulting in ferroelectric fatigue.

Relaxor Single Crystals with Giant k31 Mode

2006 ◽  
Vol 45 ◽  
pp. 2412-2421
Author(s):  
Toshio Ogawa
Keyword(s):  
Single Crystal ◽  
Electromechanical Coupling ◽  
Impedance Measurement ◽  
Hysteresis Loops ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Poling Direction ◽  
Length Direction ◽  
Relaxor Single Crystals ◽  
The Relationship

Giant electromechanical coupling factor of k31 mode over 86% was found for (100) Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 and (110) Pb[(Mg1/3Nb2/3)0.74Ti0.26]O3 single-crystal plates poled in the [100] and [110] directions, respectively. The P-E hysteresis loops in the single-crystal plates with giant k31 became asymmetric. Furthermore, the frequency response of impedance in these plates with giant k31 consisted of a single vibration in the length direction. A mechanism to realize giant k31 can be explained by the relationship between the crystal plane and poling direction. In addition, the existence of giant piezoelectric d31 constant was proven by the strain measurement as well as by the impedance measurement.

scholarly journals Effect of the matrix subsystem on hydrostatic parameters of a novel 1–3-type piezo-composite

2015 ◽  
Vol 08 (05) ◽  
pp. 1550049 ◽  
Author(s):  
Vitaly Yu. Topolov ◽  
Christopher R. Bowen ◽  
Paolo Bisegna ◽  
Anatoly E. Panich
Keyword(s):  
Elastic Properties ◽  
Electromechanical Coupling ◽  
Volume Fraction ◽  
Electromechanical Coupling Factor ◽  
Ferroelectric Ceramic ◽  
Coupling Factor ◽  
Polyurethane Composite ◽  
The Matrix ◽  
Type Composite

The influence of the aspect ratio and volume fraction of ferroelectric ceramic inclusions in a 0–3 matrix on the hydrostatic parameters of a three-component 1–3-type composite is studied to demonstrate the important role of the elastic properties of the two-component matrix on the composite performance. Differences in the elastic properties of the 0–3 matrix and single-crystal rods lead to a considerable dependence of the hydrostatic response of the composite on the anisotropy of the matrix elastic properties. The performance of a 1–0–3 0.92 Pb ( Zn 1/3 Nb 2/3) O 3–0.08 PbTiO 3 SC/modified PbTiO 3 ceramic/polyurethane composite suggests that this composite system is of interest for hydroacoustic applications due to its high hydrostatic piezoelectric coefficients [Formula: see text] and [Formula: see text], squared figure of merit [Formula: see text], and electromechanical coupling factor [Formula: see text].

Sign in / Sign up

Export Citation Format

Share Document