Experimental investigation of shell foundations on dry sand

1998 ◽  
Vol 35 (5) ◽  
pp. 847-857 ◽  
Author(s):  
Adel Hanna ◽  
Mohamed Abdel-Rahman
Keyword(s):  
Experimental Investigation ◽  
World War Ii ◽  
Bearing Capacity ◽  
Axial Loading ◽  
Ultimate Bearing Capacity ◽  
Embedment Depth ◽  
Foundation Engineering ◽  
Dense Sand ◽  
Geotechnical Design ◽  
Shell Foundations

Shells are usually used as structural elements in buildings. In Germany they showed remarkable resistance to the effects of bombing during World War II. About 1 decade later, the possibility of employing shells in foundation engineering was explored. Surveys of the literature indicate that shell foundations have been employed effectively in different parts of the world and were proven to provide an overall economical alternative to the conventional flat foundations. However, the geotechnical design of these footings remained the same as for their respective flat ones. Accordingly, the advantages of shell geometry in foundation engineering has not yet been explored in the design of these footings. The objective of the present study is to examine the overall geotechnical behavior of three types of shell foundations resting on sand under axial loading conditions, namely, triangular, conical, and pyramidal shells. Furthermore, the resulting bearing capacities and settlements will be compared with conventional strip, circular, and square flat foundations. The present paper presents an experimental study on nine foundation models tested on loose, medium, and dense sand states. The influence of shell configuration and embedment depth on the ultimate bearing capacity and settlement will be presented. The results of the present experimental investigation have shown the admirable performance of shell foundations with respect to ultimate bearing capacity and settlement characteristics. Shell foundations provide higher resistance to lateral loading as compared with flat ones, and thus they will perform better in earthquake regions.Key words: shell foundation, experimental investigation, bearing capacity, settlement, sand, geotechnical engineering.

Experimental Study on Mechanical Properties of Larch Glulam Columns under Axial Compression

2016 ◽  
Vol 847 ◽  
pp. 38-45
Author(s):  
Xian Yan Zhou ◽  
Dan Zeng ◽  
Zhi Feng Wang
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Bearing Capacity ◽  
Axial Strain ◽  
Slenderness Ratio ◽  
Axial Loading ◽  
Ultimate Bearing Capacity ◽  
Reduction Factor ◽  
Peak Strain ◽  
Short Columns

At present, the relevant researches of Glulam columns in China are mainly restricted to short columns. In order to study the mechanical properties of long columns under axial loading, an experimental study on five different slenderness ratios of Larch Glulam columns was carried out. With slenderness ratio changing, the variations of experimental data such as axial strain, lateral deflection at mid-height, ultimate bearing capacity, and peak strain were comparatively analyzed. The failure pattern and failure mechanism of long columns were discussed. The results indicate that the ultimate bearing capacity of Larch Glulam columns gradually decreases as the slenderness radio increases and the failure mode is gradually converted from strength failure to instability failure. The ultimate load reduction factor is obtained by regression analysis based on the experiment results of Larch Glulam short columns. The basis for design and application of Larch Glulam columns are provided.

Experimental Investigation on Steel H-Beam Prestressed with Externally High Strength Steel Bars

2014 ◽  
Vol 578-579 ◽  
pp. 155-159 ◽  
Author(s):  
Peng Cheng Zhu ◽  
Ming Kang Gou ◽  
Yin Zhi Zhou
Keyword(s):  
Experimental Investigation ◽  
Bearing Capacity ◽  
High Strength Steel ◽  
High Strength ◽  
Ultimate Bearing Capacity ◽  
Prestressing Force ◽  
Steel Bars ◽  
Post Tensioning ◽  
H Beam ◽  
Externally Prestressing

The external post-tensioning technique has been commonly used in the construction field because it facilitates the analysis of structures and is widely applicable for many types of structures. In this research, 12 steel H-beams were built and tested in terms of the amount of tendon or prestressing force. The results show that the externally prestressing method can increase ultimate bearing capacity of the beams. The prestressing force is the significant factor that influence the strengthening of steel H-beams. However, the amount of deviators cannot significantly influence the bearing capacity.

Experimental Investigation on Anchorage Mechanisms of Self-Locked Anchor under Combined Tension and Shear

2010 ◽  
Vol 163-167 ◽  
pp. 3600-3603
Author(s):  
Ying Li ◽  
Dong Zi Pan ◽  
Lian Zhang
Keyword(s):  
Experimental Investigation ◽  
Bearing Capacity ◽  
Fracture Pattern ◽  
Ultimate Bearing Capacity ◽  
Design Codes ◽  
Design Recommendations ◽  
Experimental Parameters ◽  
Current Design ◽  
New Construction ◽  
New Type

Self-locked anchor is a new type of underreamed anchor, and which is more and more frequently used in both new construction and structural retrofitting or strengthening projects. Nevertheless, current design codes do not contain suitable design recommendations for these anchors. This study investigates the anchorage mechanisms of self-locked anchor under combined tension and shear loadings. The experimental parameters mainly include anchor diameters (Φ16 and Φ20) and loading angles (0°, 30°, 45°, and 60°). The present results indicate the characters of axial and transverse deformations, the ultimate bearing capacity, the fracture pattern of anchor, and the breakout model of concrete.

scholarly journals Pressure Settlement Behaviour and Bearing Capacity of Asymmetric Embedded Plus Shaped Footing on Layered Sand

2021 ◽  
Vol 31 (3) ◽  
pp. 152-176
Author(s):  
Priyanka Rawat ◽  
Rakesh Kumar Dutta
Keyword(s):  
Bearing Capacity ◽  
Numerical Study ◽  
Friction Angle ◽  
Thickness Ratio ◽  
Embedment Depth ◽  
Loose Sand ◽  
Dense Sand ◽  
Comparison Of The Results ◽  
Abaqus Software ◽  
Settlement Behaviour

Abstract The aim of the present numerical study was to analyse the pressure settlement behaviour and bearing capacity of asymmetric plus shaped footing resting on loose sand overlying dense sand at varying embedment depth. The numerical investigation was carried out using ABAQUS software. The effect of depth of embedment, friction angle of upper loose and lower dense sand layer and thickness of upper loose sand on the bearing capacity of the asymmetric plus shaped footing was studied in this investigation. Further, the comparison of the results of the bearing capacity was made between the asymmetric and symmetric plus shaped footing. The results reveal that with increase in depth of embedment, the dimensionless bearing capacity of the footings increased. The highest increase in the dimensionless bearing capacity was observed at embedment ratio of 1.5. The increase in the bearing capacity was 12.62 and 11.40 times with respect to the surface footings F1 and F2 corresponding to a thickness ratio of 1.5. The lowest increase in the dimensionless bearing capacity was observed at embedment ratio of 0.1 and the corresponding increase in the bearing capacity was 1.05 and 1.02 times with respect to the surface footing for footings F1 and F2 at a thickness ratio of 1.5.

Numerical study of ultimate bearing capacity of rectangular footing on layered sand

2020 ◽  
Vol 1 (101) ◽  
pp. 15-26
Author(s):  
V. Panwar ◽  
R.K. Dutta
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Bearing Capacity ◽  
Numerical Study ◽  
Friction Angle ◽  
Ultimate Bearing Capacity ◽  
Loose Sand ◽  
Sand Layer ◽  
Element Analysis ◽  
Dense Sand

Purpose: The purpose of this study is to investigate the ultimate bearing capacity of the rectangular footing resting over layered sand using finite element method. Design/methodology/approach: Finite element analysis was used to investigate the dimensionless ultimate bearing capacity of the rectangular footing resting on a limited thickness of upper dense sand layer overlying limitless thickness of lower loose sand layer. The friction angle of the upper dense sand layer was varied from 41° to 46° whereas for the lower loose sand layer it was varied from 31° to 36°. Findings: The results reveal that the dimensionless ultimate bearing capacity was found to increase up to an H/W ratio of about 1.75 beyond which the increase was marginal. The results further reveal that the dimensionless ultimate bearing capacity was the maximum for the upper dense and lower loose sand friction angles of 46° and 36°, while it was the lowest for the upper dense and lower loose sands corresponding to the friction angle of 41° and 31°. For H/W = 0.5 and 2, the dimensionless bearing capacity decreases with the increase in the L/W ratio from 0.5 to 6 beyond which the dimensionless ultimate bearing capacity remains constant for all combinations of parameters. The results were presented in nondimensional manner and compared with the previous studies available in literature. Research limitations/implications: The analysis is performed using a ABAQUS 2017 software. The limitation of this study is that only finite element analysis is performed without conducting any experiments in the laboratory. Further the study is conducted only for the vertical loading. Practical implications: This proposed numerical study can be used to predict the ultimate bearing capacity of the rectangular footing resting on layered sand. Originality/value: The present study gives idea about the ultimate bearing capacity of rectangular footing when placed on layered sand (dense sand over loose sand) as well as the effect of thickness of top dense sand layer on the ultimate bearing capacity. The findings could be used to calculate the ultimate bearing capacity of the rectangular footing on layered sand.

Ultimate capacity of flexible piles under eccentric and inclined loads

1989 ◽  
Vol 26 (1) ◽  
pp. 34-42 ◽  
Author(s):  
G. G. Meyerhof ◽  
D. P. Ghosh
Keyword(s):  
Bearing Capacity ◽  
Soft Clay ◽  
Ultimate Bearing Capacity ◽  
Embedment Depth ◽  
Pile Groups ◽  
Single Model ◽  
Eccentric Load ◽  
Inclined Loads ◽  
Load Tests ◽  
Ultimate Moment

The ultimate bearing capacity of flexible single model piles and small pile groups of timber and nylon in loose sand and soft clay has been determined under various combinations of eccentricity and inclination of the load varying in direction from vertical to horizontal. The results of the load tests are presented in the form of polar bearing capacity diagrams and they are compared with the theoretical estimates based on the concept of an effective embedment depth in terms of the behaviour of equivalent rigid piles. Reasonable agreement has been found between the observed and predicted ultimate bearing capacity of flexible piles under any combination of eccentricity and inclination of loads. Key words: flexible piles, pile groups, ultimate bearing capacity, ultimate moment, model test, eccentric load, inclined load, sand, clay.

Ultimate bearing capacity of conical shell foundations

2014 ◽  
Vol 52 (3) ◽  
pp. 507-523
Author(s):  
J.E. Colmenares ◽  
So-Ra Kang ◽  
Young-Jin Shin ◽  
Jong-Ho Shin
Keyword(s):  
Bearing Capacity ◽  
Conical Shell ◽  
Ultimate Bearing Capacity ◽  
Shell Foundations
Sign in / Sign up

Export Citation Format

Share Document