NUMERICAL MODELING OF WALL THINNING DEFECTS CHARACTERIZATION: APPLICATIONS IN LAMB WAVE GENERATION AND INTERACTION

2008 ◽  
Vol 22 (11) ◽  
pp. 935-940
Author(s):  
HYUNJO JEONG ◽  
SEUNG-SEOK LEE ◽  
YOUNG-GIL KIM
Keyword(s):  
Guided Waves ◽  
Lamb Waves ◽  
Mode Conversion ◽  
Wave Interaction ◽  
Guided Wave ◽  
Destructive Interference ◽  
Wall Thinning ◽  
Mode Dispersion ◽  
Periodic Ring ◽  
Axisymmetric Scattering

The generation of axisymmetric Lamb waves and interaction with wall thinning (corrosion) defects in hollow cylinders are simulated using the finite element method. Guided wave interaction with defects in cylinders is challenged by the multi-mode dispersion and the mode conversion. In this paper, two longitudinal, axisymmetric modes are generated using the concept of a time-delay periodic ring arrays (TDPRA), which makes use of the constructive/destructive interference concept to achieve the unidirectional emission and reception of guided waves. The axisymmetric scattering by the wall thinning extending in full circumference of a cylinder is studied with a two-dimensional FE simulation. The effect of wall thinning depth, axial extension, and the edge shape on the reflections of guided waves is discussed.

scholarly journals Time-Domain Hybrid Global-Local Prediction of Guided Waves Interaction with Damage

2013 ◽  
Vol 558 ◽  
pp. 116-127 ◽  
Author(s):  
Matthieu Gresil ◽  
Victor Giurgiutiu
Keyword(s):  
Finite Element ◽  
Wave Propagation ◽  
Time Domain ◽  
Guided Waves ◽  
Lamb Waves ◽  
Mode Conversion ◽  
Wave Interaction ◽  
Guided Wave ◽  
Element Mesh ◽  
The Time Domain

This paper presents a hybrid finite element and analytical method to predict the 1-D guided wave propagation interaction with damage for nondestructive evaluation (NDE) and structural health monitoring (SHM) application. The finite element mesh is used to describe the region around the damage (defects or flaws). In contrast to other hybrid models developed elsewhere, the interaction between Lamb waves and defects is computed in the time domain using the explicit solver of the commercial finite element method (FEM) software ABAQUS. Analytical methods can perform efficient modeling of wave propagation but are limited to simple geometries. Realistic structures with complicated geometries are usually modeled with the FEM. However, to obtain an accurate wave propagation solution at ultrasonic frequencies is computationally intensive and may become prohibitive for realistic structures. In response to today's complex cases not covered by the simulation tools available, we aim to develop an efficient and accessible tool for SHM applications. This tool will be based on a hybrid coupling between analytical solutions and time domain numerical codes. Lamb wave interaction with a notch is investigated by using this method, and the results obtained are with respect to transmission, reflection and mode conversion. Because of the symmetric mode shape, S0 is more sensitive to the shallow notch than A0. By making use of the fact that the reflection increases with increase in notch depth and mode conversion are maximized when the notch is around half through the thickness of the plate, the reflection and conversion coefficients can be used to characterize the depth of the notch.

A Wall Thinning Detection and Quantification Based on Guided Wave Mode Conversion Features

2006 ◽  
Vol 321-323 ◽  
pp. 795-798 ◽  
Author(s):  
Youn Ho Cho ◽  
Won Deok Oh ◽  
Joon Hyun Lee
Keyword(s):  
Long Range ◽  
Guided Waves ◽  
Velocity Dispersion ◽  
Mode Conversion ◽  
Group Velocity Dispersion ◽  
Wave Mode ◽  
Guided Wave ◽  
Wall Thinning ◽  
Theoretical Analyses ◽  
Data Calibration

This study presents a feasibility of using guided waves for a long-range inspection of pipe through investigation of mode conversion and scattering pattern from edge and wall-thinning in a steel pipe. Phase and group velocity dispersion curves for reference modes of pipes are illustrated for theoretical analyses. Predicted modes could be successfully generated by controlling frequency, receiver angle and wavelength. The dispersive characteristics of the modes from and edge wall-thinning are compared and analyzed respectively. The mode conversion characteristics are distinct depending on dispersive pattern of modes. Experimental feasibility study on the guided waves was carried out to explore wall thinning part in pipe for data calibration of a long range pipe monitoring by comb transducer and laser.

An FEM Simulation for Guided Elastic Wave Generation and Reflection in Hollow Cylinders With Corrosion Defects

2001 ◽  
Vol 124 (1) ◽  
pp. 108-117 ◽  
Author(s):  
Wenhao Zhu
Keyword(s):  
Mode Conversion ◽  
Fem Simulation ◽  
Guided Wave ◽  
Destructive Interference ◽  
Tubular Structures ◽  
Wave Reflections ◽  
Periodic Ring ◽  
Hollow Cylinders ◽  
Corrosion Defects ◽  
Wave Emission

The generation and reflection of guided elastic waves in hollow cylinders with corrosion defects have been investigated numerically for the purpose of nondestructive evaluation (NDE) of tubular structures. A new guided wave transducer model, time-delay periodic ring arrays (TDPRAs), has been used to generate the axisymmetric guided wave modes in hollow cylinders, and this is simulated by a finite element calculation. Unidirectional guided wave emission can be achieved by arranging a TDPRA’s parameters according to the principle of constructive and destructive interference. The guided wave reflections by axisymetric and nonaxisymmetric corrosion defects are analyzed using a 2-D and a 3-D FE simulation, respectively. The reflection features as well as mode conversion under the L0,1 and L0,2 mode incidences are discussed in association with the corrosion depth, the axial and circumferential extents in hollow cylinders.

scholarly journals Longitudinal Guided Wave Inspection of Small-Diameter Elbowed Steel Tubes with a Novel Squirrel-Cage Magnetostrictive Sensor

2019 ◽  
Vol 2019 ◽  
pp. 1-9
Author(s):  
Yao Liu ◽  
Xiucheng Liu ◽  
Chehua Yang ◽  
Wenxin Guo ◽  
Bin Wu ◽  
...  
Keyword(s):  
Finite Element ◽  
Guided Waves ◽  
Mode Conversion ◽  
Small Diameter ◽  
Longitudinal Mode ◽  
Guided Wave ◽  
Wall Defect ◽  
Squirrel Cage ◽  
Simulation Results ◽  
Magnetostrictive Sensor

In the study, ultrasonic longitudinal mode guided waves were employed to detect defects in elbowed tubes (without welds) with a diameter of 10 mm. Finite element simulation results highlighted that the emitted L(0,1) mode guided waves experienced strong reflection and mode conversion at the elbow region to generate F(1,1) mode, followed by slow and weak F(2,1) mode. The guided wave reflected from the elbow with a through-wall defect was manifested as two overlapped wave packets, which were good indicators of a defective elbow. To conduct L(0,1) mode guided waves inspection on the small-diameter elbowed tubes, a novel tailored squirrel-cage magnetostrictive sensor was employed in the experiment. The new sensor employed the configuration of segmental iron-cobalt strips and small-size permanent magnet arrays. The entire sensor is composed of two identical C-shaped sensor elements and can be recycled and installed conveniently. Experimental results obtained from healthy and defective tubes were consistent with the conclusions obtained from finite element simulations. An artificial through-wall defect at the elbow and a notch defect at the straight part of the tube could be simultaneously detected by L(0,1) mode guided waves through comparing experimental signals with simulation results.

Inspection of Concrete-Metal Rod Interface Using Guided Waves

2000 ◽  
Author(s):  
Won-Bae Na ◽  
Tribikram Kundu ◽  
Mohammad R. Ehsani
Keyword(s):  
Lamb Wave ◽  
Guided Waves ◽  
Lamb Waves ◽  
Guided Wave ◽  
Ultrasonic Transducers ◽  
Interface Debonding ◽  
Long Distance ◽  
Steel Rebar ◽  
Steel Bars ◽  
Steel Rebars

Abstract The feasibility of detecting interface degradation and separation of steel rebars in concrete beams using Lamb waves is investigated in this paper. It is shown that Lamb waves can easily detect these defects. A special coupler between the steel rebar and ultrasonic transducers has been used to launch non-axisymmetric guided waves in the steel rebar. This investigation shows that the Lamb wave inspection technique is an efficient and effective tool for health monitoring of reinforced concrete structures because the Lamb wave can propagate a long distance along the reinforcing steel bars embedded in concrete as the guided wave and is sensitive to the interface debonding between the steel rebar and concrete.

Early Fatigue Damage Evaluation of Nonlinear Guided Wave Imaging in Hyperelastic Materials

2021 ◽  
Author(s):  
Chengwei Zhao ◽  
Sunia Tanweer ◽  
Jian Li ◽  
Min Lin ◽  
Xiang Zhang ◽  
...  
Keyword(s):  
Fatigue Damage ◽  
Guided Waves ◽  
Lamb Waves ◽  
Tone Burst ◽  
Guided Wave ◽  
Third Order ◽  
Hyperelastic Materials ◽  
Third Order Elastic Constants ◽  
Wave Imaging ◽  
Processing Platform

Abstract Nonlinear ultrasonic guided waves have superior sensitivity of the early fatigue damage. This paper investigates the analysis of the second harmonics of Lamb waves in a free boundary aluminum plate, and the internal resonance conditions between the Lamb wave primary modes and the second harmonics. The Murnaghan’s model is implemented in a finite element (FE) analysis to describe the hyperelastic constitutive relation for nonlinear acoustic modeling. The second harmonics of s0 mode are actuated by a 60kHz Hanning-windowed tone burst. A guided wave signal processing platform is developed for tomographic imaging. The different stages of fatigue are reflected by the changes of third-order elastic constants (TOECs) in Murnaghan’s model. The reconstructed damage locations match well with the actual ones cross different degrees and depths of fatigue.

scholarly journals Warped Wigner-Hough Transform for Defect Reflection Enhancement in Ultrasonic Guided Wave Monitoring

2012 ◽  
Vol 2012 ◽  
pp. 1-15 ◽  
Author(s):  
Luca De Marchi ◽  
Emanuele Baravelli ◽  
Giampaolo Cera ◽  
Nicolò Speciale ◽  
Alessandro Marzani
Keyword(s):  
Hough Transform ◽  
Guided Waves ◽  
Lamb Waves ◽  
Guided Wave ◽  
Nonlinear Signal Processing ◽  
Localization Accuracy ◽  
Time Frequency ◽  
Ultrasonic Guided Wave ◽  
Inspection Systems ◽  
Nonlinear Signal

To improve the defect detectability of Lamb wave inspection systems, the application of nonlinear signal processing was investigated. The approach is based on a Warped Frequency Transform (WFT) to compensate the dispersive behavior of ultrasonic guided waves, followed by a Wigner-Ville time-frequency analysis and the Hough Transform to further improve localization accuracy. As a result, an automatic detection procedure to locate defect-induced reflections was demonstrated and successfully tested by analyzing numerically simulated Lamb waves propagating in an aluminum plate. The proposed method is suitable for defect detection and can be easily implemented for real-world structural health monitoring applications.

scholarly journals Quantitative mapping of thickness variations along a ray path using geometrical full waveform inversion and guided wave mode conversion

2022 ◽  
Vol 478 (2257) ◽  
Author(s):  
Peng Zuo ◽  
Peter Huthwaite
Keyword(s):  
Guided Waves ◽  
Mode Conversion ◽  
Waveform Inversion ◽  
Guided Wave ◽  
Direct Access ◽  
Thickness Variation ◽  
Full Waveform Inversion ◽  
Large Area ◽  
Wave Inversion ◽  
Full Waveform

Quantitative guided wave thickness mapping in plate-like structures and pipelines is of significant importance for the petrochemical industry to accurately estimate the minimum remaining wall thickness in the presence of corrosion, as guided waves can inspect a large area without needing direct access. Although a number of inverse algorithms have been studied and implemented in guided wave reconstruction, a primary assumption is widely used: the three-dimensional guided wave inversion of thickness is simplified as a two-dimensional acoustic wave inversion of velocity, with the dispersive nature of the waves linking thickness to velocity. This assumption considerably simplifies the inversion procedure; however, it makes it impossible to account for mode conversion. In reality, mode conversion is quite common in guided wave scattering with asymmetric wall loss, and compared with non-converted guided wave modes, converted modes may provide greater access to valuable information about the thickness variation, which, if exploited, could lead to improved performance. Geometrical full waveform inversion (GFWI) is an ideal tool for this, since it can account for mode conversion. In this paper, quantitative thickness reconstruction based on GFWI is developed in a plate cross-section and applied to study the performance of thickness reconstruction using mode conversion.

scholarly journals Nonlinear Guided Wave Tomography for Detection and Evaluation of Early-Life Material Degradation in Plates

Sensors ◽  
2021 ◽  
Vol 21 (16) ◽  
pp. 5498
Author(s):  
Chengwei Zhao ◽  
Sunia Tanweer ◽  
Jian Li ◽  
Min Lin ◽  
Xiang Zhang ◽  
...  
Keyword(s):  
Early Life ◽  
Guided Waves ◽  
Lamb Waves ◽  
Tone Burst ◽  
Guided Wave ◽  
Material Degradation ◽  
Third Order Elastic Constants ◽  
Metal Plates ◽  
Wave Tomography ◽  
Aluminum Plates

In this paper, the possibility of using nonlinear ultrasonic guided waves for early-life material degradation in metal plates is investigated through both computational modeling and study. The analysis of the second harmonics of Lamb waves in a free boundary aluminum plate, and the internal resonance conditions between the Lamb wave primary modes and the second harmonics are investigated. Subsequently, Murnaghan’s hyperelastic model is implemented in a finite element (FE) analysis to study the response of aluminum plates subjected to a 60 kHz Hanning-windowed tone burst. Different stages of material degradation are reflected as the changes in the third order elastic constants (TOECs) of the Murnaghan’s model. The reconstructed degradations match the actual ones well across various degrees of degradation. The effects of several relevant factors on the accuracy of reconstructions are also discussed.

scholarly journals Attenuation of a Slow Subsonic A0 Mode Ultrasonic Guided Wave in Thin Plastic Films

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1648 ◽  
Author(s):  
Rymantas Kažys ◽  
Reimondas Šliteris ◽  
Liudas Mažeika ◽  
Olgirdas Tumšys ◽  
Egidijus Žukauskas
Keyword(s):  
Guided Waves ◽  
High Efficiency ◽  
Lamb Waves ◽  
Ultrasonic Transducer ◽  
Plane Waves ◽  
Ultrasound Velocity ◽  
Guided Wave ◽  
Low Frequencies ◽  
Plastic Films ◽  
Thin Plastic

The ultrasonic testing technique using Lamb waves is widely used for the non-destructive testing and evaluation of various structures. For air-coupled excitation and the reception of A0 mode Lamb waves, leaky guided waves are usually exploited. However, at low frequencies (<100 kHz), the velocity of this mode in plastic and composite materials can become slower than the ultrasound velocity in air, and its propagation in films is accompanied only by an evanescent wave in air. To date, the information about the attenuation of the slow A0 mode is very contradictory. Therefore, the objective of this investigation was the measurement of the attenuation of the slow A0 mode in thin plastic films. The measurement of the attenuation of normal displacements of the film caused by a propagating slow A0 mode is discussed. The normal displacements of the film at different distances from the source were measured by a laser interferometer. In order to reduce diffraction errors, the measurement method based on the excitation of cylindrical but not plane waves was proposed. The slow A0 mode was excited in the polyvinylchloride film by a dry contact type ultrasonic transducer made of high-efficiency PMN-32%PT strip-like piezoelectric crystal. It was found that that the attenuation of the slow A0 mode in PVC film at the frequency of 44 kHz is 2 dB/cm. The obtained results can be useful for the development of quality control methods for plastic films.

Sign in / Sign up

Export Citation Format

Share Document