Investigations on the effects of obstacles on the surfaces of blades of the centrifugal pump to suppress cavitation development

2021 ◽  
pp. 2150327
Author(s):  
Weiguo Zhao ◽  
Bao Guo
Keyword(s):  
Numerical Simulation ◽  
Kinetic Energy ◽  
Centrifugal Pump ◽  
Cavitation Flow ◽  
Cavitation Model ◽  
Cavitation Performance ◽  
Simulation Results ◽  
Specific Speed ◽  
And Control ◽  
Good Agreement

This paper proposes a new method that obstacles are attached to both the suction and pressure surfaces of the blades to suppress cavitation development. A centrifugal pump with a specific speed of 32 is selected as the physical model to perform the external characteristic and cavitation performance experiments. SST [Formula: see text] turbulence model and Zwart cavitation model were employed to simulate the unsteady cavitation flow in the pump. The results indicate that the numerical simulation results are in good agreement with the experimental counterparts. After the obstacles are arranged, the maximum head decrease is only 1.37%, and the relative maximum drop of efficiency is 1.12%. Obstacles have minimal impacts on the variations of head and efficiency under all flow rate conditions. The distribution of vapor volume in the centrifugal pump is significantly reduced after obstacles are arranged and the maximum fraction reduction is 53.6%. The amplitude of blade passing frequency decreases significantly. While obstacles decrease the intensity of turbulent kinetic energy near the wall in the impeller passages to effectively reduce the distribution of cavitation bubbles, and control the development of cavitation. After the obstacles are set, the strength of the vortex in the impeller passages is weakened significantly, the shedding of the vortex is suppressed, flow in the impeller becomes more stable.

scholarly journals Numerical Simulation Analysis of Cavitation Performance of Tandem Propeller

2018 ◽  
Vol 36 (3) ◽  
pp. 509-515 ◽  
Author(s):  
Xiaoxu Du ◽  
Zhengdong Zhang
Keyword(s):  
Numerical Simulation ◽  
Simulation Analysis ◽  
Cavitation Number ◽  
Hydrodynamic Characteristics ◽  
Turbulent Model ◽  
Cavitation Model ◽  
Cavitation Phenomenon ◽  
Cavitation Performance ◽  
Simulation Results ◽  
Good Agreement

The steady non cavitation hydrodynamic characteristics of CLB4-55-1 tandem propeller and the steady cavitation flows of NACA66 hydrofoil are numerically studied firstly based on the RANS equations of homogeneous multiphase using CFD theory, combined with the SST k-ω turbulent model and Z-G-B cavitation model. Numerical simulation results are in good agreement with the experimental results, which indicates that the numerical method is reliable and accurate. Then, the cavitation performance of the tandem propeller are numerical simulated and analyzed. The results show that the computational model can predict the cavitation performance of tandem propeller accurately. The cavitation performance of tandem propeller is nearly the same as single propeller, however, the cavitation phenomenon of back propeller is greater than the head propeller at certain advance coefficient and cavitation number. The cavitation phenomenon will disappear with the increase of the advance coefficient or the cavitation number.

Theory and application of two-dimension viscous hydraulic design of the ultra-low specific-speed centrifugal pump

2019 ◽  
Vol 234 (1) ◽  
pp. 58-71 ◽  
Author(s):  
Cong Wang ◽  
Yongxue Zhang ◽  
Hucan Hou ◽  
Zhiyi Yuan
Keyword(s):  
Boundary Layer ◽  
Centrifugal Pump ◽  
Diagnostic Model ◽  
Two Dimension ◽  
Cavitation Performance ◽  
Hydraulic Design ◽  
Displacement Thickness ◽  
Low Specific Speed ◽  
Specific Speed ◽  
Low Efficiency

Low efficiency and bad cavitation performance restrict the development of the ultra-low specific-speed centrifugal pump (ULSSCP). In this research, combined turbulent boundary layer theory with two-dimension design and two-dimension viscous hydraulic design method has been proposed to redesign a ULSSCP. Through the solution of the displacement thickness in the boundary layer, a less curved blade profile with a larger outlet angle was obtained. Then the hydraulic and cavitation performance of the reference pump and the designed pump were numerically studied. The comparison of performance of the reference pump calculated by the numerical and experimental results revealed a better agreement. Research shows that the average hydraulic efficiency and head of the designed pump improve by 2.9% and 3.3%, respectively. Besides, the designed pump has a better cavitation performance. Finally, through the internal flow analysis with entropy production diagnostic model, a 24.8% drop in head loss occurred in the designed pump.

scholarly journals Experiment and simulation about the effect of wear-ring abrasion on the performance of a marine centrifugal pump

2021 ◽  
Vol 13 (2) ◽  
pp. 168781402199811
Author(s):  
Wu Xianfang ◽  
Du Xinlai ◽  
Tan Minggao ◽  
Liu Houlin
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Pressure Pulsation ◽  
Vibration Velocity ◽  
Test Results ◽  
Obvious Effect ◽  
Performance Change ◽  
Pump Test ◽  
Simulation Results ◽  
Axis Passing

The wear-ring abrasion can cause performance degradation of the marine centrifugal pump. In order to study the effect of front and back wear-ring clearance on a pump, test and numerical simulation were used to investigate the performance change of a pump. The test results show that the head and efficiency of pump decrease by 3.56% and 9.62% respectively at 1.0 Qd due to the wear-ring abrasion. Under 1.0 Qd, with the increase of the front wear-ring the vibration velocity at pump foot increases from 0.4 mm/s to 1.0 mm/s. The axis passing frequency (APF) at the measuring points increases significantly and there appears new characteristic frequency of 3APF and 4APF. The numerical simulation results show that the front wear-ring abrasion affects the flow at the inlet of the front chamber of the pump and impeller passage. And the back wear-ring abrasion has obvious effect on the flow in the back chamber of the pump and impeller passage, while the multi-malfunction of the front wear-ring abrasion and back wear-ring abrasion has the most obvious effect on the flow velocity and flow stability inside pump. The pressure pulsation at Blade Passing Frequency (BPF) of the three schemes all decrease with the increase of the clearance.

scholarly journals Optimal Design of Slit Impeller for Low Specific Speed Centrifugal Pump Based on Orthogonal Test

2021 ◽  
Vol 9 (2) ◽  
pp. 121
Author(s):  
Yang Yang ◽  
Ling Zhou ◽  
Hongtao Zhou ◽  
Wanning Lv ◽  
Jian Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Large Scale ◽  
Internal Flow ◽  
Orthogonal Test ◽  
Centrifugal Pumps ◽  
Initial Model ◽  
Low Specific Speed ◽  
Specific Speed ◽  
Four Levels

Marine centrifugal pumps are mostly used on board ship, for transferring liquid from one point to another. Based on the combination of orthogonal testing and numerical simulation, this paper optimizes the structure of a drainage trough for a typical low-specific speed centrifugal pump, determines the priority of the various geometric factors of the drainage trough on the pump performance, and obtains the optimal impeller drainage trough scheme. The influence of drainage tank structure on the internal flow of a low-specific speed centrifugal pump is also analyzed. First, based on the experimental validation of the initial model, it is determined that the numerical simulation method used in this paper is highly accurate in predicting the performance of low-specific speed centrifugal pumps. Secondly, based on the three factors and four levels of the impeller drainage trough in the orthogonal test, the orthogonal test plan is determined and the orthogonal test results are analyzed. This work found that slit diameter and slit width have a large impact on the performance of low-specific speed centrifugal pumps, while long and short vane lap lengths have less impact. Finally, we compared the internal flow distribution between the initial model and the optimized model, and found that the slit structure could effectively reduce the pressure difference between the suction side and the pressure side of the blade. By weakening the large-scale vortex in the flow path and reducing the hydraulic losses, the drainage trough impellers obtained based on orthogonal tests can significantly improve the hydraulic efficiency of low-specific speed centrifugal pumps.

Numerical Simulation on Thixo-Forging of Magnesium Matrix Composite

2011 ◽  
Vol 189-193 ◽  
pp. 2535-2538 ◽  
Author(s):  
Hong Yan ◽  
Wen Xian Huang
Keyword(s):  
Numerical Simulation ◽  
Matrix Composite ◽  
Metal Flow ◽  
Magnesium Matrix Composite ◽  
Magnesium Matrix ◽  
Simulation Based ◽  
Prior Literature ◽  
Simulation Results ◽  
Computer Numerical Simulation ◽  
Good Agreement

The thixo-forging of magnesium matrix composite was analyzed with computer numerical simulation based on rigid viscoplastic finite element method. The constitutive model of SiCp/AZ61 composite was established in our prior literature. Behavior of metal flow and temperature field were obtained. The differences between traditional forging and thixo-forging processes were analyzed. Results indicated that thixo-forging was better in filling cavity than forging. Simulation results were good agreement with experimental ones.

scholarly journals Numerical Simulations of V-Shaped Plates Subjected to Blast Loadings: A Validation Study

2016 ◽  
Vol 10 (11) ◽  
pp. 203
Author(s):  
Mohd Zaid Othman ◽  
Qasim H. Shah ◽  
Muhammad Akram Muhammad Khan ◽  
Tan Kean Sheng ◽  
M. A. Yahaya ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Numerical Simulations ◽  
Variable Mass ◽  
Blast Loading ◽  
Experimental Results ◽  
Average Difference ◽  
Simulation Results ◽  
Blast Loadings ◽  
Carrier Vehicle ◽  
Good Agreement

A series of numerical simulations utilizing LS-DYNA was performed to determine the mid-point deformations of V-shaped plates due to blast loading. The numerical simulation results were then compared with experimental results from published literature. The V-shaped plate is made of DOMEX 700 and is used underneath an armour personal carrier vehicle as an anti-tank mine to mitigate the effects of explosion from landmines in a battlefield. The performed numerical simulations of blast loading of V-shaped plates consisted of various angles i.e. 60°, 90°, 120°, 150° and 180°; variable mass of explosives located at the central mid-point of the V-shaped vertex with various stand-off distances. It could be seen that the numerical simulations produced good agreement with the experimental results where the average difference was about 26.6%.

Numerical Simulation of the Kinetic Energy Projectile Oblique Penetration into the Concrete

2014 ◽  
Vol 989-994 ◽  
pp. 982-985
Author(s):  
Jun Chen ◽  
Xiao Jun Ye
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Kinetic Energy ◽  
Three Dimensional ◽  
Test Results ◽  
Destruction Process ◽  
3D Finite Element ◽  
Finite Element Software ◽  
Simulation Results ◽  
Target Characteristics

ANSYS-LS/DYNA 3D finite element software projectile penetrating concrete target three-dimensional numerical simulation , has been the target characteristics and destroy ballistic missile trajectory , velocity and acceleration and analyze penetration and the time between relationship , compared with the test results , the phenomenon is consistent with the simulation results. The results show that : the destruction process finite element software can better demonstrate concrete tests revealed the phenomenon can not be observed , estimated penetration depth and direction of the oblique penetration missile deflection .

Downshifting Control Strategy for Dual Clutch Transmission With Single Clutch Slippage

2016 ◽  
Author(s):  
Jikai Liu ◽  
Biao Ma ◽  
Heyan Li ◽  
Man Chen ◽  
Jianwen Chen
Keyword(s):  
Control Strategy ◽  
Control Strategies ◽  
Bench Test ◽  
Dual Clutch Transmission ◽  
Pressure Profiles ◽  
Simulation Results ◽  
And Control ◽  
Engagement And Disengagement ◽  
External Loads ◽  
Good Agreement

The cooperation mode between the engagement and disengagement clutches for vehicles equipped with Dual Clutch Transmission (DCT) is of vital importance to achieve a smooth gearshift, in particular for the downshift process as its unavoidable power interruption during the inertia phase. Hence, to elevate the performance of DCT downshifting process, an analytical model and experimental validation for the analysis, simulation and control strategy are presented. Optimized pressure profiles applied on two clutches are obtained based on the detailed analysis of downshifting process. Then, according to the analysis results, a novel control strategy that can achieve downshift task with only one clutch slippage is proposed. The system model is established on Matlab/Simulink platform and used to study the variation of output torque and speed in response to different charging pressure profiles and various external loads during downshifting process. Simulation results show that, compared with conventional control strategies, the proposed one can not only avoid the torque hole and power circulation, but shorten the shift time and reduce the friction work. Furthermore, to validate the effectiveness of the control strategy, the bench test equipped with DCT is conducted and the experiment results show a good agreement with the simulation results.

Numerical Simulation of Slope Excavation in Highway Renovation and Expansion Project

2014 ◽  
Vol 580-583 ◽  
pp. 827-830
Author(s):  
Gen Chuan Luo ◽  
Zhong Ming He ◽  
Xin Luo ◽  
Qing Guo Hu
Keyword(s):  
Numerical Simulation ◽  
Stability Analysis ◽  
Stress And Strain ◽  
Regular Pattern ◽  
Expansion Process ◽  
Excavation Process ◽  
Slope Excavation ◽  
Object Use ◽  
Simulation Results ◽  
And Control

Slope stability analysis requires detect and control the stress and strain timely. Familiar with the slope‘s stress and strain changes in excavation process has important guiding significance for the actual construction. In this paper, choose a slope in Guangxi freeway renovation and expansion process as the research object. Use FLAC3D to analysis the stress and displacement simulation results of this slope excavation step by step. Summarize the excavation regular pattern.

The Rotating Cavitation Performance of a Centrifugal Pump with a Splitter-Bladed Inducer under Different Rotational Speed

2015 ◽  
Vol 32 (3) ◽  
Author(s):  
XiaoMei Guo ◽  
ZuChao Zhu ◽  
BaoLing Cui ◽  
Yi Li
Keyword(s):  
Centrifugal Pump ◽  
Rotational Speed ◽  
High Speed ◽  
Internal Flow ◽  
Centrifugal Pumps ◽  
Cavitation Flow ◽  
Operation Condition ◽  
Cavitation Performance ◽  
Cavitation Behavior ◽  
Suction Performance

AbstractDesigning inducer is one of the effective ways to improve the suction performance of high-speed centrifugal pumps. The operation condition including rotational speeds can affect the internal flow and external performance of high-speed centrifugal pumps with an inducer. In order to clarify the rotating cavitation performance of a centrifugal pump with a splitter-bladed inducer under different rotational speed, a centrifugal pump with a splitter-bladed inducer is investigated in the work. By using Rayleigh–Plesset equations and Mixture model, the cavitation flow of centrifugal pump is numerically simulated, as well as the external performance experimental test is carried out. It is found that the cavitation area increases with the rotational speeds. The location of the passage where cavitation is easy to appear is explored. Asymmetric cavitation behavior is observed. That, the trail of the inducer is easy to take cavitation when the rotational speed is increased to a degree, is also observed. The trend of

Sign in / Sign up

Export Citation Format

Share Document