Downshifting Control Strategy for Dual Clutch Transmission With Single Clutch Slippage

2016 ◽  
Author(s):  
Jikai Liu ◽  
Biao Ma ◽  
Heyan Li ◽  
Man Chen ◽  
Jianwen Chen
Keyword(s):  
Control Strategy ◽  
Control Strategies ◽  
Bench Test ◽  
Dual Clutch Transmission ◽  
Pressure Profiles ◽  
Simulation Results ◽  
And Control ◽  
Engagement And Disengagement ◽  
External Loads ◽  
Good Agreement

The cooperation mode between the engagement and disengagement clutches for vehicles equipped with Dual Clutch Transmission (DCT) is of vital importance to achieve a smooth gearshift, in particular for the downshift process as its unavoidable power interruption during the inertia phase. Hence, to elevate the performance of DCT downshifting process, an analytical model and experimental validation for the analysis, simulation and control strategy are presented. Optimized pressure profiles applied on two clutches are obtained based on the detailed analysis of downshifting process. Then, according to the analysis results, a novel control strategy that can achieve downshift task with only one clutch slippage is proposed. The system model is established on Matlab/Simulink platform and used to study the variation of output torque and speed in response to different charging pressure profiles and various external loads during downshifting process. Simulation results show that, compared with conventional control strategies, the proposed one can not only avoid the torque hole and power circulation, but shorten the shift time and reduce the friction work. Furthermore, to validate the effectiveness of the control strategy, the bench test equipped with DCT is conducted and the experiment results show a good agreement with the simulation results.

Control strategy optimization for a dual-clutch transmission downshift with a single slipping clutch during the torque phase

2017 ◽  
Vol 232 (5) ◽  
pp. 651-666 ◽  
Author(s):  
Jikai Liu ◽  
Biao Ma ◽  
Heyan Li ◽  
Man Chen ◽  
Guoqiang Li
Keyword(s):  
Control Strategy ◽  
Power Flow ◽  
Control Strategies ◽  
Poor Quality ◽  
Dual Clutch Transmission ◽  
Flow Conditions ◽  
Robust Controller ◽  
Simulation Results ◽  
The Relationship ◽  
Good Agreement

During the torque phase, appropriate coordination between two clutches is of vital importance to the dual-clutch transmission so that a high-quality shift is achieved without clutch interaction and engine flare, because a poor-quality shift definitely extends the shift time and increases the friction work. Concerning this problem, two different power flow conditions during the torque phase are discussed in detail, after investigation of the dual-clutch transmission downshift process and the design of an H∞ robust controller for the inertia phase. The results obtained indicate that, if two clutches are slipping simultaneously during the torque phase, either power interruption or power circulation occurs. Thus, by optimizing the relationship between the two clutches, a novel control strategy is proposed for the dual-clutch transmission so that the downshift process is accomplished with only one slipping clutch, in order to obtain the highest system efficiency. The system model was established on the MATLAB/Simulink platform and used to study the variations in the torque and the speed output in response to different control strategies. The simulation results show that, with the smooth inertia phase guaranteed by the robust controller, the proposed control strategy not only can avoid power interruption or power circulation during the torque phase but also can shorten the shift time (from 1.1 s to 0.8 s) and reduce the jerk level (from 6.8 m/s3 to 5.7 m/s3) effectively, in comparison with the conventional control strategy. Finally, to validate the effectiveness of the proposed control strategy, bench tests on a dual-clutch transmission were carried out, and the test data obtained show good agreement with the simulation results.

Detection Method and Control Strategy of Active Power for Wind Farm Connected into Grid

2013 ◽  
Vol 380-384 ◽  
pp. 2962-2966
Author(s):  
Chun Guang Tian ◽  
De Xin Li ◽  
Li Xia Cai ◽  
Tian Dong ◽  
Xiao Juan Han
Keyword(s):  
Control Strategy ◽  
Wind Farm ◽  
Detection Method ◽  
Control Strategies ◽  
Active Power ◽  
Detection Methods ◽  
Grid System ◽  
Simulation Results ◽  
And Control ◽  
Huge Challenge

As one of main clean energies, wind power has been developed fast, but the fluctuations of active power at a wind farm is a huge challenge for the grid system, thus it is essential for wind farm connected into grid to detection the active power. This paper studied control strategies and detection methods of the active power at a wind farm. Simulation results showed the effective detection of active power at a wind farm can improve the characteristics of the grid and the ability of wind farm to regulate the grid and increase the scheduled ability of wind farm.

Control of inverters in standalone andgrid-connected microgrid using different control strategies

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Vikash Gurugubelli ◽  
Arnab Ghosh
Keyword(s):  
Transient Response ◽  
Control Strategy ◽  
Control Strategies ◽  
Power Balance ◽  
Droop Control ◽  
Content Type ◽  
Simulink Simulation ◽  
Time Simulation ◽  
Simulation Results ◽  
First Time

Purpose The share of renewable energy sources (RESs) in the power system is increasing day by day. The RESs are intermittent, therefore maintaining the grid stability and power balance is very difficult. The purpose of this paper is to control the inverters in microgrid using different control strategies to maintain the system stability and power balance. Design/methodology/approach In this paper, different control strategies are implemented to the voltage source converter (VSC) to get the desired performance. The DQ control is a basic control strategy that is inherently present in the droop and virtual synchronous machine (VSM) control strategies. The droop and VSM control strategies are inspired by the conventional synchronous machine (SM). The main objective of this work is to design and implement the three aforementioned control strategies in microgrid. Findings The significant contributions of this work are: the detailed implementation of DQ control, droop control and VSM control strategies for VSC in both grid-connected mode and standalone mode is presented; the MATLAB/Simulink simulation results and comparative studies of the three aforementioned controllers are introduced first time in the proposed work; and the opal-RT digital real-time simulation results of the proposed VSM control show the superiority in transient response compared to the droop control strategy. Research limitations/implications In the power system, the power electronic-based power allowed by VSM is dominated by the conventional power which is generated from the traditional SM, and then the issues related to stability still need advance study. There are some differences between the SM and VSM characteristics, so the integration of VSM with the existing system still needs further study. Economical operation of VSM with hybrid storage is also one of the future scopes of this work. Originality/value The significant contributions of this work are: the detailed implementation of DQ control, droop control and VSM control strategies for VSC in both grid-connected mode and standalone mode is presented; the MATLAB/Simulink simulation results and comparative studies of the three aforementioned controllers are introduced first time in the proposed work; and the opal-RT digital real-time simulation results of the proposed VSM control show the superiority in transient response compared to the droop control strategy.

Study and Simulation on the Energy Efficiency Management Control Strategy of Ship Based on Clean Propulsion System

2015 ◽  
Author(s):  
Kai Wang ◽  
Xinping Yan ◽  
Yupeng Yuan
Keyword(s):  
Energy Efficiency ◽  
Energy Consumption ◽  
Control Strategy ◽  
Control Strategies ◽  
Management Control ◽  
Propulsion System ◽  
Power Requirement ◽  
Doubly Fed ◽  
System Configurations ◽  
And Control

Nowadays, with the higher voice of ship energy saving and emission reduction, the research on energy efficiency management is particularly necessary. Energy efficiency management and control of ships is an effective way to improve the ship energy efficiency. In this paper, according to the new clean propulsion system configurations of 5000 tons of bulk carrier, the energy efficiency management control strategy of the clean propulsion system is designed based on the model of advanced brushless doubly-fed shaft generator, propulsion system using LNG/diesel dual fuel engine and energy consumption of the main engine for reducing energy consumption. The simulation model of the entire propulsion system and the designed control strategy were designed. The influence of the engine speed on the ship energy efficiency was analyzed, and the feasibility of the energy efficiency management control strategies was verified by simulation using Matlab/Simulink. The results show that the designed strategies can ensure the power requirement of the whole ship under different conditions and improve the ship energy efficiency and reduce CO2 emissions.

Study on a global control strategy for rotation speed with different work states in variable-speed constant-frequency wind turbines

2011 ◽  
Vol 225 (7) ◽  
pp. 968-976 ◽  
Author(s):  
G Zheng ◽  
H Xu ◽  
X Wang ◽  
J Zou
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Control Strategy ◽  
Control Strategies ◽  
Stable Operation ◽  
Constant Frequency ◽  
Global Control ◽  
Control Rules ◽  
The Individual ◽  
And Control

This paper studies the operation of wind turbines in terms of three phases: start-up phase, power-generation phase, and shutdown phase. Relationships between the operational phase and control rules for the speed of rotation are derived for each of these phases. Taking into account the characteristics of the control strategies in the different operational phases, a global control strategy is designed to ensure the stable operation of the wind turbine in all phases. The results of simulations are presented that indicate that the proposed algorithm can control the individual phases when considered in isolation and also when they are considered in combination. Thus, a global control strategy for a wind turbine that is based on a single algorithm is presented which could have significant implications on the control and use of wind turbines.

Formal Modeling and Analysis of Collaborative Humanoid Robotics

2019 ◽  
pp. 1086-1108
Author(s):  
Yujian Fu ◽  
Zhijiang Dong ◽  
Xudong He
Keyword(s):  
Petri Net ◽  
Control Strategies ◽  
Formal Modeling ◽  
Humanoid Robotics ◽  
Modeling And Analysis ◽  
Agent Based ◽  
Design And Implementation ◽  
Simulation Results ◽  
And Control ◽  
Successful Collaboration

A humanoid robot is inherently complex due to the heterogeneity of accessory devices and to the interactions of various interfaces, which will be exponentially increased in multiple robotics collaboration. Therefore, the design and implementation of multiple humanoid robotics (MHRs) remains a very challenging issue. It is known that formal methods provide a rigorous analysis of the complexity in both design of control and implementation of systems. This article presents an agent-based framework of formal modeling on the design of communication and control strategies of a team of autonomous robotics, to attain the specified tasks in a coordinated manner. To ensure a successful collaboration of multiple robotics, this formal agent-based framework captures behaviors in Petri Net models and specifies collaboration operations in four defined operations. To validate the framework, a non-trivial soccer bot set was implemented and simulation results were discussed.

Modeling the System and Component Performance Interactions of a SOFC Based APU for Changes in Application Load: Transient Response and Control Strategy

2004 ◽  
Author(s):  
D. F. Rancruel ◽  
M. R. von Spakovsky
Keyword(s):  
Transient Response ◽  
Control Strategy ◽  
Control Strategies ◽  
Control Variable ◽  
System Level ◽  
System Component ◽  
System Response ◽  
Optimal Control Strategy ◽  
Synthesis Design ◽  
And Control

Solid-Oxide-Fuel-Cell (SOFC) stacks respond in seconds to changes in load while the balance of plant subsystem (BOPS) responds in times several orders of magnitude higher. This dichotomy diminishes the reliability and performance of SOFC electrodes with changes in load. In the same manner current and voltage ripples which result from particular power electronic subsystem (PES) topologies and operation produce a negative effect on the SOFC stack subsystem (SS) performance. The difference in transient response among the sub-systems must be approached in a way which makes operation of the entire system not only feasible but ensures that efficiency and power density, fuel utilization, fuel conversion, and system response are optimal at all load conditions. Thus, a need exists for the development of transient component- and system-level models of SOFC based auxiliary power units (APUs), i.e. coupled BOPS, SS, and PES, and the development of methodologies for optimizing subsystem responses and for investigating system-interaction issues. In fact the transient process occurring in a SOFC based APU should be systematically treated during the entire creative process of synthesis, design, and operational control, leading in its most general sense to a dynamic optimization problem. This entails finding an optimal system/component synthesis/design, taking into account on- and off-design operation, which in turn entails finding an optimal control strategy and control profile for each sub-system/component and control variable. Such an optimization minimizes an appropriate objective function while satisfying all system constraints. A preliminary set of chemical, thermal, electrochemical, electrical, and mechanical models based on first principles and validated with experimental data have been developed and implemented using a number of different platforms. These models have been integrated in order to be able to perform component, subsystem, and system analyses as well as develop optimal syntheses/designs and control strategies for transportation and stationary SOFC based APUs. Some pertinent results of these efforts are presented here.

The Study on Starting Control of ER Clutch for Vehicle

2012 ◽  
Vol 490-495 ◽  
pp. 1759-1762 ◽  
Author(s):  
Jian Hua Wang ◽  
Hao Xu ◽  
Fei Xie
Keyword(s):  
Control Strategy ◽  
Control Voltage ◽  
Start Time ◽  
Evaluation Indexes ◽  
Working Principle ◽  
Simulation Results ◽  
And Control ◽  
Start Process ◽  
Er Fluid ◽  
Starting Control

This paper proposed a new design scheme for automatic clutch of AMT which is based on electrorheological (ER) fluid. Through analyzing the working principle and its transfer characteristics of ER fluid, it discussed the start process of vehicle and control strategy of ER Clutch. By changing the control voltage, ER clutch satisfied the requirements of evaluation indexes such as start time and impact degree. The simulation results showed that the control strategy can realize starting rapidly and steadily which would meet the start requirements of economical automobiles

Analysis of Control Strategy for Extended-Range Electric Vehicle

2011 ◽  
Vol 135-136 ◽  
pp. 261-267
Author(s):  
Hai Tao Min ◽  
Dong Jin Ye ◽  
Yuan Bin Yu
Keyword(s):  
Electric Vehicles ◽  
Control Strategy ◽  
Optimal Strategy ◽  
Control Strategies ◽  
Power Train ◽  
Operating Modes ◽  
Load Following ◽  
Extended Range ◽  
Main Components ◽  
And Control

This paper introduced the structure of Extended-Range Electric Vehicles as well as its characteristics. Principle researches have been offered on the parameters matching of the power-train and main components. Operating modes and control strategies were discussed, especially the two control strategies of charge sustaining mode which is shown as load following strategy and engine optimal strategy, and the effects of both control strategies are simulated and analyzed. The results indicate that the load following strategy can obviously extend battery’s lifespan, but the engine optimal strategy can reduce fuel consumption and emission effectively.

Study of Topology and Control Strategy of the Bidirectional Energy Storage Converter Based on Three-Level

2013 ◽  
Vol 397-400 ◽  
pp. 1169-1173
Author(s):  
Hong Wei Tang ◽  
Xi Kun Chen ◽  
Yan Xia Gao
Keyword(s):  
Mathematical Model ◽  
Energy Storage ◽  
Control Strategy ◽  
Lithium Battery ◽  
Decoupling Control ◽  
Midpoint Potential ◽  
Simulation Results ◽  
And Control ◽  
The Mathematical Model ◽  
Battery Module

To adapt to the requirements of the charging and discharging of the lithium battery, the paper presents a three-level based bidirectional energy storage converter topology.It has strong adaptability and can manage the charge and discharge of multi-series and parallel battery module. The mathematical model of the converter is analyzed, and the two operation modes of the converter control strategy are studied; Analysis the feed-forward decoupling control of three-level rectifier, and the variable scale factor is used to control midpoint potential. The simulation results demonstrate the feasibility of the design.

Sign in / Sign up

Export Citation Format

Share Document