NANOCOMPOSITE Al2O3–Y2O3 FILMS ON CARBON STEEL

2009 ◽  
Vol 16 (06) ◽  
pp. 797-800 ◽  
Author(s):  
FANG LI ◽  
MINGMING YAO ◽  
XUELEI PENG
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Carbon Steel ◽  
Photoelectron Spectroscopy ◽  
Mass Gain ◽  
Electrochemical Process ◽  
Sintering Process ◽  
X Ray ◽  
Gain Measurement ◽  
Scanning Electron

The nanocomposite Al 2 O 3– Y 2 O 3 films were prepared on the surface of carbon steel by an electrochemical process and a sintering process. High-resolution field emission scanning electron microscopy (FE-SEM) and X-ray photoelectron spectroscopy (XPS) were used to characterize the films, indicating that the films have nanostructures and the deposited alumina layers have a composition close to the stoichiometry of Al 2 O 3. SEM and mass gain measurement are adopted to study the oxidation resistance of films on carbon steel. It is proved that this kind of film is effective in protecting the substrate from oxidation. The mechanisms accounting for such effects have been discussed.

scholarly journals Investigation of Spin Coating Cerium-Doped Hydroxyapatite Thin Films with Antifungal Properties

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 464
Author(s):  
Simona Liliana Iconaru ◽  
Mihai Valentin Predoi ◽  
Patrick Chapon ◽  
Sofia Gaiaschi ◽  
Krzysztof Rokosz ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Spin Coating ◽  
Laser Scanning ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
X Ray ◽  
Antifungal Properties ◽  
Scanning Electron

In this study, the cerium-doped hydroxyapatite (Ca10−xCex(PO4)6(OH)2 with xCe = 0.1, 10Ce-HAp) coatings obtained by the spin coating method were presented for the first time. The stability of the 10Ce-HAp suspension particles used in the preparation of coatings was evaluated by ultrasonic studies, transmission electron microscopy (TEM), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The surface morphology of the 10Ce-HAp coating was studied by SEM and atomic force microscopy (AFM) techniques. The obtained 10Ce-HAp coatings were uniform and without cracks or unevenness. Glow discharge optical emission spectroscopy (GDOES) and X-ray photoelectron spectroscopy (XPS) were used for the investigation of fine chemical depth profiling. The antifungal properties of the HAp and 10Ce-HAp suspensions and coatings were assessed using Candida albicans ATCC 10231 (C. albicans) fungal strain. The quantitative antifungal assays demonstrated that both 10Ce-HAp suspensions and coatings exhibited strong antifungal properties and that they successfully inhibited the development and adherence of C. albicans fungal cells for all the tested time intervals. The scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) visualization of the C. albicans fungal cells adherence to the 10Ce-HAp surface also demonstrated their strong inhibitory effects. In addition, the qualitative assays also suggested that the 10Ce-HAp coatings successfully stopped the biofilm formation.

Light Burning Condition of Preparing Dolomite Clinker Using Natural Dolomite

2018 ◽  
Vol 281 ◽  
pp. 156-162
Author(s):  
Wang Nian Zhang ◽  
Xi Tang Wang ◽  
Zhou Fu Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Burning Temperature ◽  
X Ray ◽  
Temperature Range ◽  
Scanning Electron

The influence of the light burning temperature on the sintering property of nature dolomite has been investigated by two-step sintering process in the temperature range 1500 °C to 1600 °C. The resulting bulk densities and apparent porosities of the sintered dolomite samples were examined, and analyzing the sintered dolomite by scanning electron microscopy and X-ray diffraction were performed. The results showed light burned at 850 °C for 3 h, the main phases of the dolomite with 3-5 grain size were MgO, CaO and little CaCO3, and then fired at 1600 °C,the density of sintering dolomite reached to 3.38 g/cm3, the apparent property was 1.2 %, the size of MgO grain up to 3.75 μm . However when dolomite light burned at 1050 °C for 3 h, the main phases were MgO and CaO, and then fired at 1600 °C,the density of sintering dolomite only was 3.30 g/cm3, the apparent property was 2.3 %, the size of MgO only was 3.05 μm .

scholarly journals Improvement of the Space Charge Suppression and Hydrophobicity Property of Cellulose Insulation Pressboard by Surface Sputtering a ZnO/PTFE Functional Film

Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1610 ◽  
Author(s):  
Li ◽  
Hao ◽  
Zhang ◽  
Hou ◽  
Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Space Charge ◽  
Photoelectron Spectroscopy ◽  
Power Transformers ◽  
Nano Structure ◽  
X Ray ◽  
Ptfe Composite ◽  
Cellulose Insulation ◽  
Scanning Electron

Oil-impregnated cellulose insulation polymer (oil-paper/pressboard insulation) has been widely used in power transformers. Establishing effective ways of improving the physical and chemical properties of the cellulose insulation polymer is currently a popular research topic. In order to improve the charge injection inhibition and hydrophobic properties of the cellulose insulation polymer used in power transformers, nano-structure zinc oxide (ZnO) and polytetrafluoroethylene (PTFE) films were fabricated on a cellulose insulation pressboard surface via reactive radio frequency (RF) magnetron sputtering. Before the fabrication of their composite film, Accelrys Materials Studio (MS) software was applied to simulate the interaction between the nanoparticles and cellulose molecules to determine the depositing sequence. Simulation results show that the ZnO nanoparticle has a better adhesion strength with cellulose molecules than the PTFE nanoparticle, so ZnO film should be sputtered at first to fabricate the ZnO/PTFE composite film for better film quality. The sputtered, thin films were characterized by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The space charge injection behavior and the hydrophobicity performance of the untreated pressboard; and the cellulose insulation pressboard with sputtered nano-structure ZnO, PTFE, and the ZnO/PTFE functional films were compared with each other. X-ray photoelectron spectroscopy results showed that ZnO, PTFE, and ZnO/PTFE functional films were all successfully fabricated on the cellulose insulation pressboard surface. Scanning electron microscopy and XRD results present the nano-structure of the sputtered ZnO, PTFE, and ZnO/PTFE functional films and their amorphous states, respectively. The ZnO/PTFE composite functional film shows an apparent space charge suppression effect and hydrophobicity. The amount of the accumulated space charge in the pressboard sputtered ZnO/PTFE composite functional film decreased by about 40% compared with that in untreated cellulose insulation pressboard, and the water contact angle (WCA) increased from 0° to 116°.

Characterization of Multiple Functional Solid Line of Graphite Ink Surface Printed by Micro-Flexographic

2015 ◽  
Vol 752-753 ◽  
pp. 1379-1383
Author(s):  
M.I. Maksud ◽  
Mohd Sallehuddin Yusof ◽  
Zaidi Embong
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Printing Plate ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Flexographic Printing ◽  
Scanning Electron

The purpose of this paper is to study a ink surface morphology, quantify the chemical composition involved in processing of graphite ink printed by flexographic printing. The methodology is to use surface sensitive technique, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) and Field Emission Scanning Electron Microscopy (FESEM). As a finding we successfully achieved 25 micron lines array using PDMS printing plate. The Originality and value of this work is surface sensitive techniques like XPS, AFM and FESEM were exclusively used in order to characterize graphite inks printed by flexographic method, using PDMS printing plate.

scholarly journals Preparation of Cerium Dioxide Layers on Titanium by Electrodeposition with Organic Solution

2017 ◽  
Vol 2017 ◽  
pp. 1-9
Author(s):  
Vaijayanti Namdeo Nande ◽  
Diana Kostyukova ◽  
Jeonghee Choi ◽  
Yong Hee Chung
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Cerium Dioxide ◽  
Average Crystallite Size ◽  
X Ray Diffraction ◽  
Organic Solution ◽  
X Ray ◽  
Titanium Foils ◽  
Scanning Electron

Layers of cerium dioxide nanoparticles were prepared on titanium by electrodeposition with organic solution. Three concentrations of cerium ions were used at 31.6 V. The organic solution was isobutanol and titanium foils were used as anodes and cathodes. Currents were monitored during the electrodeposition. Deposition times ranged from 0.5 to 8 h. Deposited Deposited layers were calcined at 700 K for 30 min. The morphology and composition of the deposited layers were examined by scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). As-prepared and calcined deposition layers were assayed to be cerium dioxide. The average crystallite size increased from 4 to 7 nm through calcination at 700 K. Sizes of calcined cerium oxide agglomerates were ranging from 73 to 146 nm for 30 min deposition and 209 to 262 nm for 8 h deposition. The electrodeposition efficiencies of 0.5 h deposition at three concentrations were measured to be highest.

Synthesis of Nanophase Noble Metal Systems Utilizing Porous Silicon

1996 ◽  
Vol 457 ◽  
Author(s):  
I. Coulthard ◽  
T. K. Sham
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Porous Silicon ◽  
Noble Metal ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Visible Range ◽  
X Ray ◽  
Metallic Salt ◽  
Scanning Electron

ABSTRACTApart from its well known ability to luminesce very intensely at room temperature in the visible range, porous silicon is also an effective reducing agent. We report the formation of several noble metal (Pd, Ag, Au, Pt) nanostructures by reductive dispersion of metal ions from aqueous solutions onto the surface of porous silicon. The nanophase systems produced by reductive deposition vary with the element deposited and the metallic salt utilized in the process. The resulting nanophase systems were studied using a variety of techniques including: scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and spectroscopie methods using synchrotron radiation.

Research on Friction and Wear Properties of Ti(C,N)/Fe Composites

2013 ◽  
Vol 650 ◽  
pp. 326-332
Author(s):  
Yang Li ◽  
Zhi Ping Sun ◽  
Rui Feng Wang ◽  
Li Yan Zou
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Friction And Wear ◽  
Adhesive Wear ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Wear Properties ◽  
X Ray ◽  
Friction And Wear Properties ◽  
Scanning Electron

The effect of different load, revolving speed ,content of Ti(C,N) and sintering process on the friction coefficient and wear rate of Ti(C,N)/Fe composites was investigated systemically. Besides, the wear morphology of Ti(C,N)/Fe composites were researched with an environment scanning electron microscopy(SEM),and the phase composition were studied by X-ray diffraction(XRD).The research shows that the wear mechanism of Ti(C,N)/Fe composites are abrasive wear and adhesive wear.

scholarly journals SYNTHESIS OF GRAPHENE-LIKE STRUCTURES BY A PLASMA-ARC DISCHARGE IN LIQUID NITROGEN

2020 ◽  
Vol 86 (10) ◽  
pp. 88-94
Author(s):  
Radyslav Panteleimonov ◽  
Oleksandr Korduban ◽  
Volodymyr Ogenko ◽  
Taras Kryshchuk
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Liquid Nitrogen ◽  
Photoelectron Spectroscopy ◽  
Arc Discharge ◽  
Plasma Arc ◽  
Doping Element ◽  
X Ray ◽  
Plasma Arc Discharge ◽  
Scanning Electron

Using scanning electron microscopy, X-ray photoelectron spectroscopy, and Raman scattering we studied the charge state of matrix and doping element atoms on the surface, morphology, and defects in the structure of graphene-like materials synthesized by plasma-arc discharge in liquid nitrogen.

Sign in / Sign up

Export Citation Format

Share Document