Research on Friction and Wear Properties of Ti(C,N)/Fe Composites

2013 ◽  
Vol 650 ◽  
pp. 326-332
Author(s):  
Yang Li ◽  
Zhi Ping Sun ◽  
Rui Feng Wang ◽  
Li Yan Zou
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Friction And Wear ◽  
Adhesive Wear ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Wear Properties ◽  
X Ray ◽  
Friction And Wear Properties ◽  
Scanning Electron

The effect of different load, revolving speed ,content of Ti(C,N) and sintering process on the friction coefficient and wear rate of Ti(C,N)/Fe composites was investigated systemically. Besides, the wear morphology of Ti(C,N)/Fe composites were researched with an environment scanning electron microscopy(SEM),and the phase composition were studied by X-ray diffraction(XRD).The research shows that the wear mechanism of Ti(C,N)/Fe composites are abrasive wear and adhesive wear.

Research on Friction Properties of VC/Fe-Based Composites

2013 ◽  
Vol 647 ◽  
pp. 654-658
Author(s):  
Yang Li ◽  
Zhi Ping Sun ◽  
Rui Feng Wang ◽  
Guo Jun Zhang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Phase Composition ◽  
Friction Coefficient ◽  
Wear Mechanism ◽  
Adhesive Wear ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

The effect of different load, revolving speed, content of VC and sintering process on the friction coefficient of VC/Fe-based composites was investigated systemically. Besides, the wear morphology of VC/Fe-based composites were researched with an environment scanning electron microscopy(SEM),and the phase composition were studied by X-ray diffraction(XRD).The research shows that the wear mechanism of VC/Fe-based composites are abrasive wear and adhesive wear.

Light Burning Condition of Preparing Dolomite Clinker Using Natural Dolomite

2018 ◽  
Vol 281 ◽  
pp. 156-162
Author(s):  
Wang Nian Zhang ◽  
Xi Tang Wang ◽  
Zhou Fu Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Burning Temperature ◽  
X Ray ◽  
Temperature Range ◽  
Scanning Electron

The influence of the light burning temperature on the sintering property of nature dolomite has been investigated by two-step sintering process in the temperature range 1500 °C to 1600 °C. The resulting bulk densities and apparent porosities of the sintered dolomite samples were examined, and analyzing the sintered dolomite by scanning electron microscopy and X-ray diffraction were performed. The results showed light burned at 850 °C for 3 h, the main phases of the dolomite with 3-5 grain size were MgO, CaO and little CaCO3, and then fired at 1600 °C,the density of sintering dolomite reached to 3.38 g/cm3, the apparent property was 1.2 %, the size of MgO grain up to 3.75 μm . However when dolomite light burned at 1050 °C for 3 h, the main phases were MgO and CaO, and then fired at 1600 °C,the density of sintering dolomite only was 3.30 g/cm3, the apparent property was 2.3 %, the size of MgO only was 3.05 μm .

scholarly journals Chemical and Wetting Analysis of the Ni-Ti Coating on SiC Improved by a 2-Step Coating-Sintering Process

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5235
Author(s):  
Yang Liu ◽  
Ying-Xin Wang ◽  
Qiang Yang ◽  
Fu Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Control Groups ◽  
X Ray ◽  
Surface Energies ◽  
Metal Ceramic ◽  
Sintering Conditions ◽  
Scanning Electron

A two-stepped coating-sintering process to prepare the qualified Ni–Ti transition applied in metal-ceramic bonding proved to be effective to improve the wetting abilities. The method was introduced in detail and compared with 2 control groups. To analyze the benefits, the morphology and composition were captured by field emission scanning electron microscopy (FE-SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The comparisons of different coating depths and different sintering conditions were also recorded and analyzed. The influence of the EDS detecting depth was a concern in the discussions. Finally, the contact angle tests and surface energies were also estimated to verify the reliability of the transition layer. The results indicated that the coating-sintering process combined with protective sintering was preferred and necessary to increase the activeness.

Evaluation of the Friction and Wear Properties of PA6 Composites Filled with Nano-SiO2

2011 ◽  
Vol 299-300 ◽  
pp. 86-89
Author(s):  
Wen Xia Wang ◽  
Jian Li
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Tribological Properties ◽  
Friction And Wear ◽  
Wear Behaviour ◽  
Wear Properties ◽  
Research Article ◽  
Friction And Wear Properties ◽  
Worn Surface ◽  
Scanning Electron

PA6 composites filled with nano-SiO2were synthesized. The aim of the research article is to study the mechanical and friction and wear behaviour of nano-SiO2reinforced PA6 composites. The worn surface of the composite was examined by scanning electron microscopy. The results showed that the addition of nano-SiO2can effectively improve the mechancial and tribological properties of the PA6 composites.

Identification of calcium oxalate crystals in dried or fixed tobacco leaf

1984 ◽  
Vol 42 ◽  
pp. 288-289
Author(s):  
Vicki L. Baliga ◽  
Mary Ellen Counts
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Calcium Oxalate ◽  
Growth And Development ◽  
Polarized Light ◽  
Calcium Oxalate Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Calcium is an important element in the growth and development of plants and one form of calcium is calcium oxalate. Calcium oxalate has been found in leaf seed, stem material plant tissue culture, fungi and lichen using one or more of the following methods—polarized light microscopy (PLM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and x-ray diffraction.Two methods are presented here for qualitatively estimating calcium oxalate in dried or fixed tobacco (Nicotiana) leaf from different stalk positions using PLM. SEM, coupled with energy dispersive x-ray spectrometry (EDS), and powder x-ray diffraction were used to verify that the crystals observed in the dried leaf with PLM were calcium oxalate.

Environmental scanning electron microscopy of fresh human gallstones reveals new morphologies of precipitated calcium salts

1992 ◽  
Vol 50 (2) ◽  
pp. 1322-1323
Author(s):  
Howard S. Kaufman ◽  
Keith D. Lillemoe ◽  
John T. Mastovich ◽  
Henry A. Pitt
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Environmental Scanning Electron Microscopy ◽  
Environmental Scanning ◽  
X Ray Diffraction ◽  
Calcium Salts ◽  
Cholesterol Gallstones ◽  
X Ray ◽  
Ca Carbonate ◽  
Scanning Electron

Gallstones contain precipitated cholesterol, calcium salts, and proteins. Calcium (Ca) bilirubinate, palmitate, phosphate, and carbonate occurring in gallstones have variable morphologies but characteristic windowless energy dispersive x-ray (EDX) spectra. Previous studies of gallstone microstructure and composition using scanning electron microscopy (SEM) with EDX have been limited to dehydrated samples. In this state, Ca bilirubinates appear as either glassy masses, which predominate in black pigment stones, or as clusters, which are found mostly in cholesterol gallstones. The three polymorphs of Ca carbonate, calcite, vaterite, and aragonite, have been identified in gallstones by x-ray diffraction, however; the morphologies of these crystals vary in the literature. The purpose of this experiment was to study fresh gallstones by environmental SEM (ESEM) to determine if dehydration affects gallstone Ca salt morphology.Gallstones and bile were obtained fresh at cholecystectomy from 6 patients. To prevent dehydration, stones were stored in bile at 37°C. All samples were studied within 4 days of procurement.

PENINGKATAN LAJU DISOLUSI ACYCLOVIR DENGAN METODE SISTEM DISPERSI PADAT MENGGUNAKAN POLOXAMER 188

2016 ◽  
Vol 5 (1) ◽  
pp. 6
Author(s):  
Budi Setiawan ◽  
Erizal Zaini ◽  
Salman Umar
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Differential Thermal Analysis ◽  
Fourier Transform Infrared ◽  
X Ray Diffraction ◽  
Poloxamer 188 ◽  
X Ray ◽  
Scanning Electron

Sebuah penelitian tentang sistem dispersi padat dari asiklovir dengan poloxamer 188 telah dilakukan formulasi dengan pencampuran secara fisika dengan rasio 1 : 1, 1 : 3, 1 : 5 dan dispersi padat 1 : 1, 1 : 3, 1 : 5 dan penggilingan 1:1 sebagai pembanding. Dispersi padat dibuat menggunakan metode pencairan (fusi), yang digabung dengan poloxamer 188 pada hotplate kemudian asiklovir dimasukkan ke dalam hasil poloxamer 188 lalu di kocok hingga membentuk masa homogen. Semua formula yang terbentuk termasuk asiklovir poloxamer 188 murni dianalisis karakterisasinya dengan Differential Thermal Analysis (DTA), X-ray Diffraction, Scanning Electron Microscopy (SEM), dan Fourier Transform Infrared (FTIR), kemudian pengambilan dilakukan  (penentuan kadar) mengunakan spektrofotometer UV pada panjang gelombang 257,08 nm dan uji laju disolusi dengan aquadest bebas CO2 menggunakan metode dayung. Hasil pengambilan  (penentuan kadar) menunjukkan bahwa semua formula memenuhi persyaratan farmakope Amerika edisi 30 dan farmakope Indonesia edisi 4 yaitu 95-110%. Sedangkan hasil uji laju disolusi untuk campuran fisik 1: 1, dan dispersi padat 1: 1, dan penggilingan 1: 1 menunjukkan peningkatan yang nyata dibandingkan asiklovir murni. Hal ini juga dapat dilihat dari hasil perhitungan statistik  menggunakan analisis varian satu arah  SPSS 17.

Structural Characterization of Gallbladder Stones Using Energy Dispersive X-ray Spectroscopy and X-ray Diffraction

2018 ◽  
Vol 21 (7) ◽  
pp. 495-500 ◽  
Author(s):  
Hassan A. Almarshad ◽  
Sayed M. Badawy ◽  
Abdalkarem F. Alsharari
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Energy Dispersive ◽  
Spectroscopic Techniques ◽  
X Ray Diffraction ◽  
Major Health Problem ◽  
X Ray ◽  
Gallbladder Stones ◽  
Pure Cholesterol ◽  
Scanning Electron

Aim and Objective: Formation of the gallbladder stones is a common disease and a major health problem. The present study aimed to identify the structures of the most common types of gallbladder stones using X-ray spectroscopic techniques, which provide information about the process of stone formation. Material and Method: Phase and elemental compositions of pure cholesterol and mixed gallstones removed from gallbladders of patients were studied using energy-dispersive X-ray spectroscopy combined with scanning electron microscopy analysis and X-ray diffraction. Results: The crystal structures of gallstones which coincide with standard patterns were confirmed by X-ray diffraction. Plate-like cholesterol crystals with laminar shaped and thin layered structures were clearly observed for gallstone of pure cholesterol by scanning electron microscopy; it also revealed different morphologies from mixed cholesterol stones. Elemental analysis of pure cholesterol and mixed gallstones using energy-dispersive X-ray spectroscopy confirmed the different formation processes of the different types of gallstones. Conclusion: The method of fast and reliable X-ray spectroscopic techniques has numerous advantages over the traditional chemical analysis and other analytical techniques. The results also revealed that the X-ray spectroscopy technique is a promising technique that can aid in understanding the pathogenesis of gallstone disease.

scholarly journals Analytical study of Buddha sculptures in Jingyin temple of Taiyuan, China

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Xiaojian Bai ◽  
Chen Jia ◽  
Zhigen Chen ◽  
Yuxuan Gong ◽  
Huwei Cheng ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Analytical Study ◽  
Energy Dispersive Spectrometry ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Ancient China ◽  
X Ray ◽  
Unique Style ◽  
Scanning Electron

AbstractWith exquisite design and unique style, the painted sculptures of Tutang Buddha and two attendants Buddha in Jingyin Temple are precious cultural heritages of China. The sculpture of Tutang Buddha, which was carved from a mound and painted by ancient craftsmen, was rarely found in ancient China. However, due to natural and human factors, the sculptures were severely damaged. Obviously, they require urgent and appropriate protection and restoration. In this study, samples taken from the sculptures were analysed through multiple analytical techniques, including scanning electron microscopy with energy dispersive spectrometry (SEM–EDS), Raman spectroscopy, X-ray diffraction (XRD), optical microscopy (OM) and granulometry. The analysis results enable us to infer the techniques used by the craftsmen in making the sculptures and provide a reliable evidence for the conservation and future protection of these and similar sculptures.

Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)

2012 ◽  
Vol 620 ◽  
pp. 314-319
Author(s):  
Nur Amira Mamat Razali ◽  
Fauziah Abdul Aziz ◽  
Saadah Abdul Rahman
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Alkaline Treatment ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Preliminary Preparation ◽  
Characterization Studies ◽  
Scanning Electron

Hardwood is wood from angiosperm trees. The characteristic of hardwood include flowers, endosperm within seeds and the production of fruits that contain the seeds. This paper aims to discuss the preparation and characterization of cellulose obtained from hardwood. The hardwood Merbau (Intsia bijuga) was chosen as raw material in this study. Alkaline treatment and delignification methods were used for the preparation of cellulose. Acid hydrolysis was employed to produce cellulose nanocrystal (CNC). The treated and untreated samples were characterized using x-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The final product, from both trated and untreated samples were then compared.

Sign in / Sign up

Export Citation Format

Share Document