COMPRESSIVE FAILURE PREDICTION FROM NONLINEAR FINITE ELEMENT ANALYSIS OF A NOTCHED 0 DEGREE COMPOSITE SPECIMEN

2002 ◽  
Vol 02 (01) ◽  
pp. 135-149
Author(s):  
MELANIE G. VIOLETTE
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Compressive Strength ◽  
Element Model ◽  
Design Criterion ◽  
Composite Specimen ◽  
Element Analysis ◽  
Buckling Instability ◽  
Experimental Values ◽  
Important Design

The strength of unidirectional composites is often lower in compression than in tension, making compressive strength an especially important design criterion. The compressive strength is sensitive to the presence of notches and stress gradients. Finite element analysis was used to determine the strain gradient at a shallow circular notch in one edge of a 0 degree carbon/epoxy composite specimen, and to predict failure due to a localized buckling instability. The specimen was first analyzed with a "global" model of the full specimen, and displacements along a curve near the notch were stored and used as boundary conditions for a more detailed "submodel" in the immediate vicinity of the notch. At the onset of instability, a displaced plot of the finite element model shows oscillations in the transverse direction along the arc of the notch, just off the centerline, which is essentially at the same location where failure initiated in the test specimens. Results are compared with experimental values for failure stress and notch strain concentration for a range of loading rates and test temperatures.

Finite Element Analysis of X-Cor Sandwich's Compressive Strength

2011 ◽  
Vol 306-307 ◽  
pp. 733-737
Author(s):  
Xu Dan Dang ◽  
Xin Li Wang ◽  
Hong Song Zhang ◽  
Jun Xiao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Compressive Strength ◽  
Failure Modes ◽  
Failure Mechanisms ◽  
Element Model ◽  
Failure Criteria ◽  
Stiffness Degradation ◽  
Element Analysis ◽  
Finite Element Software

In this article the finite element software was used to analyse the values for compressive strength of X-cor sandwich. During the analysis, the failure criteria and materials stiffness degradation rules of failure mechanisms were proposed. The failure processes and failure modes were also clarified. In the finite element model we used the distributions of failure elements to simulate the failure processes. Meanwhile the failure mechanisms of X-cor sandwich were explained. The finite element analysis indicates that the resin regions of Z-pin tips fail firstly and the Z-pins fail secondly. The dominant failure mode is the Z-pin elastic buckling and the propagation paths of failure elements are dispersive. Through contrast the finite element values and test results are consistent well and the error range is -7.6%~9.5%. Therefore the failure criteria and stiffness degradation rules are reasonable and the model can be used to predict the compressive strength of X-cor sandwich.

The Finite Element Study of the Compressive Strength of Typical Waveform Corrugated Box

2012 ◽  
Vol 262 ◽  
pp. 390-394 ◽  
Author(s):  
Wei Yuan ◽  
Wen Cai Xu ◽  
Gai Mei Zhang ◽  
Li Hua Xie
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Compressive Strength ◽  
Optimization Design ◽  
Element Model ◽  
Element Analysis ◽  
Corrugated Board ◽  
The Finite Element Analysis ◽  
The Finite Element Model ◽  
Element Study

The finite element model of a 0201 V-shaped, U-shaped, and UV-shaped single corrugated board corrugated boxes are established. The stress distribution and strain of the three types of waveform corrugated box to withstand the pressure of the top surface stacking are calculated. Three kinds of corrugated board compression are analyzed. Analysis of the structure shows that the V-shaped corrugated board has good rigidity, U-type corrugated box has good cushioning properties, and the range during which the UV type is a better choice. This is consistent with the experimental results, prove the validity of the finite element analysis, and provide data basis for optimization design of the shape of the corrugated board corrugated waveform.

Finite Element Analysis for the Collapse Accident of One 110kV Transmission Tower

2013 ◽  
Vol 690-693 ◽  
pp. 1940-1944
Author(s):  
Ming Jian Jian ◽  
Du Qing Zhang ◽  
Guang Cheng Zhang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Transmission Line ◽  
Element Model ◽  
Strong Wind ◽  
Transmission Tower ◽  
Element Analysis ◽  
Line System ◽  
Buckling Instability

One collapse tower of 110 kV transmission line was taken as an example and a finite element model for the coupled tower-line system was established for investigating the effects of the strong wind on the transmission tower and line. The result shows that the selected standard of material of some rod members is lower, and the area of their section is relatively small. Main legs present buckling instability because of being in compression under action of the strong wind, which leads to the collapse accident of the towers.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

Behaviour of Axially Loaded Composite Wall Panel by Using Finite Element Analysis

2015 ◽  
Vol 815 ◽  
pp. 49-53
Author(s):  
Nur Fitriah Isa ◽  
Mohd Zulham Affandi Mohd Zahid ◽  
Liyana Ahmad Sofri ◽  
Norrazman Zaiha Zainol ◽  
Muhammad Azizi Azizan ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Composite Structures ◽  
Element Analysis ◽  
Steel Sheets ◽  
Linear Behavior ◽  
Non Linear ◽  
Composite Wall ◽  
Experimental Values ◽  
Civil Engineering Infrastructure

In order to promote the efficient use of composite materials in civil engineering infrastructure, effort is being directed at the development of design criteria for composite structures. Insofar as design with regard to behavior is concerned, it is well known that a key step is to investigate the influence of geometric differences on the non-linear behavior of the panels. One possible approach is to use the validated numerical model based on the non-linear finite element analysis (FEA). The validation of the composite panel’s element using Trim-deck and Span-deck steel sheets under axial load shows that the present results have very good agreement with experimental references. The developed finite element (FE) models are found to reasonably simulate load-displacement response, stress condition, giving percentage of differences below than 15% compared to the experimental values. Trim-deck design provides better axial resistance than Span-deck. More concrete in between due to larger area of contact is the factor that contributes to its resistance.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Finite Element Analysis and Optimization of Long-Span Gantry NC Machining Center Structure

2011 ◽  
Vol 346 ◽  
pp. 379-384
Author(s):  
Shu Bo Xu ◽  
Yang Xi ◽  
Cai Nian Jing ◽  
Ke Ke Sun
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Method ◽  
Dynamic Performance ◽  
Plate Thickness ◽  
Element Model ◽  
Wall Structure ◽  
Characteristic Analysis ◽  
Element Analysis ◽  
Dynamic Performance Analysis

The use of finite element theory and modal analysis theory, the structure of the machine static and dynamic performance analysis and prediction using optimal design method for optimization, the new machine to improve job performance, improve processing accuracy, shorten the development cycle and enhance the competitiveness of products is very important. Selected for three-dimensional CAD modeling software-UG NX4.0 and finite element analysis software-ANSYS to set up the structure of the beam finite element model, and then post on the overall structure of the static and dynamic characteristic analysis, on the basis of optimized static and dynamic performance is more superior double wall structure of the beam. And by changing the wall thickness and the thickness of the inner wall, as well as the reinforcement plate thickness overall sensitivity analysis shows that changes in these three parameters on the dynamic characteristics of post impact. Application of topology optimization methods, determine the optimal structure of the beam ultimately.

scholarly journals Analysis for Wrinkling Behavior of Girth-Welded Line Pipe

1996 ◽  
Author(s):  
Luiz T. Souza ◽  
David W. Murray
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Internal Pressure ◽  
Experimental Test ◽  
Element Model ◽  
Element Analysis ◽  
Line Pipe ◽  
New Era ◽  
Analytical Tools

The paper presents results for finite element analysis of full-sized girth-welded specimens of line pipe and compares these results with the behavior exhibited by test specimens subjected to constant axial force, internal pressure and monotonically increasing curvatures. Recommendations for the ‘best’ type of analytical finite element model are given. Comparisons between the behavior predicted analytically and the observed behavior of the experimental test specimens are made. The mechanism of wrinkling is explained and the evolution of the deformed configurations for different wrinkling modes is examined. It is concluded that the analytical tools now available are sufficiently reliable to predict the behavior of pipe in a manner that was not previously possible and that this should create a new era for the design and assessment of pipelines if the technology is properly exploited by industry.

scholarly journals Finite element analysis of mechanical behavior of concrete-filled square steel tube short columns with inner I-shaped CFRP profiles subjected to bi-axial eccentric load

2018 ◽  
Author(s):  
Guochang Li ◽  
Zhichang Zhan ◽  
Zhijian Yang ◽  
Yu Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Compressive Strength ◽  
Steel Tube ◽  
Concrete Compressive Strength ◽  
Eccentric Load ◽  
Element Analysis ◽  
Composite Columns ◽  
Short Columns ◽  
Square Steel Tube

The concrete-filed square steel tube with inner I-shaped CFRP profiles short columns under bi-axial eccentric load were investigated by the finite element analysis software ABAQUS. The working mechanism of the composite columns which is under bi-axial eccentric load are investigated by using the stress distribution diagram of steel tube concrete and the I-shaped CFRP profiles. In this paper, the main parameters; eccentric ratio, steel ratio, steel yield strength, concrete compressive strength and CFRP distribution rate of the specimens were investigated to know the mechanical behavior of them. The interaction between the steel tube and the concrete interface at different characteristic points of the composite columns were analyzed. The results showed that the ultimate bearing capacity of the concrete-filed square steel tube with inner I-shaped CFRP profiles short columns under bi-axial eccentric load decrease with the increase of eccentric ratio, the ultimate bearing capacity of the composite columns increase with the increase of steel ratio, steel yield strength, concrete compressive strength and CFRP distribution rate. The contact pressure between the steel tube and the concrete decreased from the corner zone to the flat zone, and the contact pressure decreased from the mid-height cross section to other sections.

Sign in / Sign up

Export Citation Format

Share Document