STRUCTURE AND MAGNETIC PROPERTIES OF NONOSIZED SnO-Fe2O3 MATERIAL OBTAINED BY BALL MILLING

2010 ◽  
Vol 09 (06) ◽  
pp. 567-570
Author(s):  
AHMED M. AL-SAIE ◽  
ADNAN JAAFAR ◽  
MOHAMED BOUOUDINA
Keyword(s):  
Magnetic Properties ◽  
Saturation Magnetization ◽  
Diffraction Pattern ◽  
Ball Milling ◽  
Magnetic Measurements ◽  
Spinel Phase ◽  
Ferromagnetic Behavior ◽  
X Ray Diffraction ◽  
X Ray ◽  
Diffraction Peaks

A mixture of Fe 2 O 3 and SnO oxides has been mechanically milled to form SnFe 2 O 4 spinel phase. X-ray diffraction pattern of the milled mixture shows that after milling, both peaks of Fe 2 O 3 and SnO remain with a drastic decrease of their intensities and broadening. The appearance of a broad halo around 2θ ~ 31° indicates the formation of an amorphous phase. After annealing at 750°C for 1 h, SnO peaks disappear completely and new diffraction peaks emerge indicating the formation of a new nanophase i.e. SnO 2. Magnetic measurements of the as-milled mixture show a ferromagnetic behavior with saturation magnetization Ms = 6.8 emu/g which drastically decreases after annealing to 0.6 emu/g.

Mechanically Driven Alloying and Magnetic Properties in Immiscible Mn80Bi20 Nanocrystalline Powders

2013 ◽  
Vol 873 ◽  
pp. 217-220
Author(s):  
Min Xu ◽  
Qun Jiao Wang
Keyword(s):  
Magnetic Properties ◽  
Mechanical Alloying ◽  
Saturation Magnetization ◽  
Ball Milling ◽  
Solid Solubility ◽  
Milling Time ◽  
Early Stage ◽  
Nanocrystalline Powders ◽  
X Ray Diffraction ◽  
X Ray

The paper has described the formation of nanocrystalline Mn80Bi20powders by mechanical alloying and studied the changes of structure and magnetic properties of the powders during the process of ball milling by using X-ray diffraction and saturation magnetization σsmeasurements. The solid solubility of bismuth in manganese increases with milling time and tends to a stable value after 80h milling. The σsof Mn80Bi20increases abruptly with milling time at the early stage and begins to decrease after 15h. At the time of 15h, the σsreaches a maximum, which is about 7Am2/kg. The result shows an interesting information that the antiferromagnetic Mn and the diamagnetic Bi produce ferromagnetic Mn80Bi20in process of mechanical alloying.

Structural and magnetic properties of pure and cobalt doped Gallium Nitride nanocrystals

2010 ◽  
Vol 1257 ◽  
Author(s):  
Vottikondala Ganesh ◽  
Suresh Sundaram ◽  
Krishnan Baskar
Keyword(s):  
Magnetic Properties ◽  
Gallium Nitride ◽  
Magnetic Measurements ◽  
Raw Materials ◽  
Ferromagnetic Behavior ◽  
Secondary Phases ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structural And Magnetic Properties ◽  
Co Doped

AbstractIn the present study pure and doped gallium nitride (GaN) nanocrystals were synthesized using gallium trichloride (GaCl3), ethylene diamine tetra acetic acid (EDTA) and cobalt chloride as raw materials at a temperature of 900 °C in ammonia (NH3) atmosphere. The XRD spectrum for pure and cobalt doped GaN nanocrystals shows the formation of single phase wurtzite structure. No impurity phases were observed in the X-ray diffraction pattern for 5% Co doped sample whereas secondary phases were observed when the doping concentration exceeds 5 %. Shift in X-ray diffraction peaks were observed in Co doped samples towards lower angle side compared to pure GaN, it confirms that the Co atoms introduces in to the GaN lattice. Transmission electron microscopy images were taken for pure and Co doped GaN. Hexagonal morphology was observed in pure GaN samples. The average size of the particle was found to be ˜20 nm for pure and Co doped GaN. The magnetic measurements were carried out for the Co (5% & 10%) doped samples both at 10K and 300K. Clear hysteresis loop in the magnetization curve suggest the presence of ferromagnetic behavior in cobalt doped GaN. Temperature dependent magnetization (M-T) measurements were also carried out for doped samples using Super Conducting Quantum Interface Device (SQUID) from 10K to 300K The results have been discussed and correlated to structural and magnetic properties of the materials.

Magnetic Study of Nanoferritas CoFe2O4 Obtained by Reaction of Combustion

2014 ◽  
Vol 798-799 ◽  
pp. 402-406
Author(s):  
Polyana Tarciana Araújo Santos ◽  
Pascally M.A. Guerra de Araújo ◽  
Ana Cristina Figueiredo de Melo Costa ◽  
Daniel R. Cornejo
Keyword(s):  
Magnetic Properties ◽  
Infrared Spectroscopy ◽  
High Intensity ◽  
Magnetic Measurements ◽  
Spinel Ferrite ◽  
Magnetic Behavior ◽  
Ferrite Nanoparticles ◽  
X Ray Diffraction ◽  
X Ray ◽  
Diffraction Peaks

The present work aims to study the magnetic properties of nanoferrita cobalt obtained by combustion reaction. The structural feature as well as the magnetic behavior when in the presence of a magnet and magnetic measurements was investigated. The resulting samples were characterized by X-ray diffraction (XRD), infrared spectroscopy (FTIR), magnetic behavior when in the presence of a magnet and magnetic measurements. The results indicated the phase single the spinel ferrite CoFe2O4, with high intensity of diffraction peaks indicating that the samples are crystalline and nanoparticle formation. The characteristic bands of spinel were observed for nanoferritas CoFe2O4. The ferrite nanoparticles were strongly attracted when in presence the magnet presenting a saturation magnetization of 58.0 emu/g, coercivity of 1.14 kOe.

scholarly journals Effects of Additives and Sintering Time on the Microstructure of Ni-Zn Ferrite and Its Electrical and Magnetic Properties

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Abdollah Hajalilou ◽  
Mansor Hashim ◽  
Halimah Mohamed Kamari
Keyword(s):  
Magnetic Properties ◽  
Saturation Magnetization ◽  
Grain Growth ◽  
Spinel Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrical And Magnetic Properties ◽  
Sintering Time ◽  
Zn Ferrite ◽  
The Relationship

This work aims to investigate the relationship between the microstructure of Ni-Zn ferrite and its electrical and magnetic properties in the presence and absence of as small amounts as 0.12% of 0.4CaO + 0.8SiO2over different sintering times. The X-ray diffraction pattern showed a single spinel phase formation in all the samples. The results indicate that grain growth occurred by increasing sintering time from 15 to 270 min in the two types of samples prepared in this study although it was greatly impeded by the additive oxides. Moreover, the oxides increase the resistivity of the ferrite and decrease its zinc loss. Magnetic properties such as induction magnetization (BS) and saturation magnetization (MS) decreased in the presence of the additives while its coercivity (HC) increased. Finally, the density of the samples was observed to increase with increasing sintering time in both types of the samples but with a higher value in the samples with no additives.

THE STRUCTURE AND MAGNETIC PROPERTIES OF ZnCr2-xFexO4

2010 ◽  
Vol 09 (06) ◽  
pp. 595-598
Author(s):  
AHMED M. AL-SAIE
Keyword(s):  
Magnetic Properties ◽  
Saturation Magnetization ◽  
Mixed Oxides ◽  
Magnetic Measurements ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Ferromagnetic Behaviour ◽  
Fe Oxides ◽  
Simple Combination

ZnCr 1-x Fe x O 4 system (with x = 0, 0.5, 1, 1.5, and 2) at the nanoscale has been successfully synthesized by a simple combination of milling mixture of Zn , Cr , and Fe oxides precursors. X-ray diffraction and magnetic measurements were carried out on the as-milled powders. XRD pattern clearly shows that the mixed oxides are all nanosized. However, as Fe 2 O 3 increases the ZnCrFeO 4 phase becomes the main phase. However, magnetic measurements do not show any significance in saturation magnetization (Ms), only when the content of Fe becomes 50% and 0.75% the Ms increased drastically to 15.4 and 16.7 emu/g respectively. However, with Fe 75% He and Mr reduced abruptly to half of their values, showing a ferromagnetic behaviour with low He .

Influence of Alloying Additions on Enhancement of Soft Magnetic Properties Effect and Crystallization in FeXSiB (X=Cu, V, Co, Zr, Nb) Amorphous Alloys

2007 ◽  
Vol 130 ◽  
pp. 171-174 ◽  
Author(s):  
Z. Stokłosa ◽  
G. Badura ◽  
P. Kwapuliński ◽  
Józef Rasek ◽  
G. Haneczok ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Crystallization Process ◽  
Annealing Temperature ◽  
Magnetic Measurements ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
X Ray ◽  
Second Stage ◽  
Transmission Electron

The crystallization and optimization of magnetic properties effects in FeXSiB (X=Cu, V, Co, Zr, Nb) amorphous alloys were studied by applying X-ray diffraction methods, high resolution transmission electron microscopy (HRTEM), resistometric and magnetic measurements. The temperatures of the first and the second stage of crystallization, the 1h optimization annealing temperature and the Curie temperature were determined for different amorphous alloys. Activation energies of crystallization process were obtained by applying the Kissinger method. The influence of alloy additions on optimization effect and crystallization processes was carefully examined.

scholarly journals Structural and Magnetic Properties of FePd Thin Film Synthesized by Electrodeposition Method

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1454
Author(s):  
Gabriele Barrera ◽  
Federico Scaglione ◽  
Matteo Cialone ◽  
Federica Celegato ◽  
Marco Coïsson ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Magnetic Properties ◽  
Deposition Time ◽  
Magnetic Measurements ◽  
X Ray Diffraction ◽  
X Ray ◽  
Fundamental Properties ◽  
Magnetic Features ◽  
Application Fields

Bimetallic nanomaterials in the form of thin film constituted by magnetic and noble elements show promising properties in different application fields such as catalysts and magnetic driven applications. In order to tailor the chemical and physical properties of these alloys to meet the applications requirements, it is of great importance scientific interest to study the interplay between properties and morphology, surface properties, microstructure, spatial confinement and magnetic features. In this manuscript, FePd thin films are prepared by electrodeposition which is a versatile and widely used technique. Compositional, morphological, surface and magnetic properties are described as a function of deposition time (i.e., film thickness). Chemical etching in hydrochloric acid was used to enhance the surface roughness and help decoupling crystalline grains with direct consequences on to the magnetic properties. X-ray diffraction, SEM/AFM images, contact angle and magnetic measurements have been carried out with the aim of providing a comprehensive characterisation of the fundamental properties of these bimetallic thin films.

The Effects of Ternary Elemental Additions on the Structure and Magnetic Properties of Nanocrystalline Feco Powders

2002 ◽  
Vol 753 ◽  
Author(s):  
I. Baker ◽  
R. G. Quiller ◽  
M. Robson ◽  
D. Wu
Keyword(s):  
Magnetic Properties ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Grain Sizes ◽  
Before And After ◽  
Diffraction Peaks ◽  
Computer Controlled ◽  
Steel Balls ◽  
Scanning Electron

ABSTRACTPowders of near-equiatomic Fe and Co were mechanically milled with additions of Zr, C, Ni, Cu and/or B for 60 hr using stainless steel balls in a Svegari attritor operated at 1300 r.p.m. under argon. The milled powders were examined before and after annealing at 600 °C. The morphologies and sizes of the powders were examined using a scanning electron microscope. The grain sizes were characterized from the widths of X-ray diffraction peaks obtained using a computer-controlled x-ray diffractometer and the lattice parameters were determined. The resulting magnetic properties were measured using a vibrating sample magnetometer.

Structural and magnetic properties of DyCo4−xFexGa compounds

2010 ◽  
Vol 25 (S1) ◽  
pp. S31-S35
Author(s):  
W. H. Zhang ◽  
J. Q. Li ◽  
Y. J. Yu ◽  
F. S. Liu ◽  
W. Q. Ao ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Magnetic Measurements ◽  
Uniaxial Anisotropy ◽  
Solubility Limit ◽  
Spin Reorientation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cell Parameters ◽  
Spin Reorientation Transition ◽  
Structural And Magnetic Properties

The structural and magnetic properties of the DyCo4−xFexGa compounds with x=0, 0.5, 1, and 1.5 have been investigated by X-ray diffraction and magnetic measurements. Powder X-ray diffraction analysis reveals that each of the DyCo4−xFexGa compounds has a hexagonal CaCu5-type structure (space group P6/mmm). The Fe solubility limit in DyCo4−xFexGa is x<1.5. The higher the value of x, the larger the unit-cell parameters a, c, V, and the 3d-sublattice moment but the smaller the 3d uniaxial anisotropy. Magnetic measurements show that the Curie temperature of DyCo4−xFexGa increases from 498 K for x=0 to 530 K for x=1.5, the compensation temperature Tcomp decreases from 286 K for x=0 to 238 K for x=1.5, and the spin-reorientation transition temperature increases from 403 K for x=0 to 530 K for x=0.5. No spin-reorientation transition was found in the samples with x=1.0 and 1.5. The saturation magnetization of DyCo4−xFexGa measured at 173 K increases but the magnetization measured at 300 K decreases with increasing Fe content x.

Sign in / Sign up

Export Citation Format

Share Document