scholarly journals Modeling the Failure Behavior of CFRP Laminates Subjected to Combined Thermal and Mechanical Loadings

2017 ◽  
Vol 09 (03) ◽  
pp. 1750033 ◽  
Author(s):  
Weina Zhao ◽  
Hongwei Song ◽  
Chenguang Huang ◽  
Yihui Huang
Keyword(s):  
Mechanical Properties ◽  
Thermal Decomposition ◽  
Carbon Fiber ◽  
Heating Rate ◽  
High Temperatures ◽  
Level Structure ◽  
Failure Behavior ◽  
Failure Strength ◽  
Heating Rates ◽  
Cfrp Laminates

This paper proposes a theoretical approach to predict the failure behavior of laminated carbon fiber reinforced polymer (CFRP) under combined thermal and mechanical loadings. Two types of CFRP Laminates, i.e., CCF300/BA9916 and T700/BA9916, are investigated, and TGA tests in both nitrogen and oxidation environments at different heating rates are carried out to obtain the thermal decomposition kinetic parameters of polymer matrix and carbon fiber. Based on the thermal decomposition behavior and a multi-level structure model, the thermal physical properties, mechanical properties and thermal deformations of the laminated composites at high temperatures are obtained. Then substituting thermally degraded properties into constitutive equations of composite materials as macroscopic defects, the damage mode and failure strength of the laminated composite under thermo-mechanical loadings is obtained. Predicted elastic properties and failure strength are compared with experimental results as well as previous models. Effects of heating rates and heating environments through rigorous physical model are considered in the present work. It is found that the heating rate significantly affects the thermal and mechanical properties, the higher the heating rate, the less degraded are the thermo-mechanical properties and failure strength at a given temperature. Young’s modulus and failure strength of T700/BA9916 are higher than those of CCF300/BA9916 at high temperatures, due to the higher volume fraction of carbon fibers, which are less weakened in thermal environment.

scholarly journals Synthesis and characterization of a new conjugated polymer containing bithiazole group and its thermal decomposition kinetics

2020 ◽  
Vol 39 (2) ◽  
pp. 227
Author(s):  
Adnan Kurt ◽  
Hacer Andan ◽  
Murat Koca
Keyword(s):  
Thermal Decomposition ◽  
Heating Rate ◽  
Conjugated Polymer ◽  
Three Dimensional ◽  
Heating Rates ◽  
Diffusion Type ◽  
Optimum Heating ◽  
Rate Loss ◽  
Kinetics Of

A new conjugated polymer containing a bithiazole group is prepared by the polycondensation of 2,2'-diamino-4,4'-bithiazole and terephthaldialdehyde in the presence of glacial acetic acid. The kinetics of thermal degradation of the new polymer are investigated by thermogravimetric analysis at different heating rates. The temperature corresponding to the maximum rate loss shifts to higher temperatures with increasing heating rate. The thermal decomposition activation energies of the conjugated polymer in a conversion range of 3–15 % are 288.4 and 281.1 kJ/mol by the Flynn–Wall–Ozawa and Kissinger methods, respectively. The Horowitz–Metzger method shows that the thermodegradation mechanism of the conjugated polymer proceeds over a three-dimensional diffusion type deceleration D3 mechanism. The optimum heating rate is 20 ºC/min.

scholarly journals Effects of Heating Rate on Formation of Globular and Acicular Austenite during Reversion from Martensite

Metals ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 266 ◽  
Author(s):  
Xianguang Zhang ◽  
Goro Miyamoto ◽  
Yuki Toji ◽  
Tadashi Furuhara
Keyword(s):  
Heating Rate ◽  
High Temperatures ◽  
The Other ◽  
Growth Mode ◽  
High Heating Rate ◽  
Heating Rates ◽  
Other Hand ◽  
High Heating ◽  
Martensite Matrix

The effects of heating rate on the formation of acicular and globular austenite during reversion from martensite in Fe–2Mn–1.5Si–0.3C alloy have been investigated. It was found that a low heating rate enhanced the formation of acicular austenite, while a high heating rate favored the formation of globular austenite. The growth of acicular γ was accompanied by the partitioning of Mn and Si, while the growth of globular γ was partitionless. DICTRA simulation revealed that there was a transition in growth mode from partitioning to partitionless for the globular austenite with an increase in temperature at high heating rate. High heating rates promoted a reversion that occurred at high temperatures, which made the partitionless growth of globular austenite occur more easily. On the other hand, the severer Mn enrichment into austenite at low heating rate caused Mn depletion in the martensite matrix, which decelerated the reversion kinetics in the later stage and suppressed the formation of globular austenite.

Influence of Rate of Heating to Aging Temperature on Precipitation Hardening in a Metastable β Titanium Alloy

2014 ◽  
Vol 1025-1026 ◽  
pp. 445-450 ◽  
Author(s):  
Ashwary Pande ◽  
Salil Sainis ◽  
Santhosh Rajaraman ◽  
Geetha Manivasagam ◽  
M. Nageswara Rao
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
Heating Rate ◽  
Aging Temperature ◽  
Alpha Phase ◽  
Slow Heating ◽  
Precipitation Reaction ◽  
Heating Rates ◽  
Rate Of Heating ◽  
Reduction In Area

A comparison between slow heating to aging temperature and direct charging at aging temperature on the microstructure and mechanical properties obtained after the aging was established for the metastable beta (β) titanium alloy Ti-15V-3Cr-3Al-3Sn. The alloy was subjected to two single aging (SA) and two duplex aging (DA) conditions, with two heating rates to aging temperature: (i) low heating rate of 5 oC/min (ii) direct charging into a furnace heated to aging temperature. The microstructure analysis was carried out using Field Emission Scanning Electron Microscopy. Mechanical Testing was carried to evaluate Ultimate Tensile Strength (UTS), 0.2% Yield Strength (YS), % Elongation (%El.), % Reduction in area (%RA) and hardness. In the case of SA samples aged at 500 °C for 8 h and 500 °C for 10 h, heating rate of 5 °C/min to aging temperature resulted in a finer microstructure but did not help in achieving better strength-ductility combination compared to direct charging. Lower rate of heating allows enough dwell time in the temperature range 250-300 oC for pre-precipitation reaction to occur which aids in fine scale precipitation of alpha phase during aging. In the case of DA samples aged at 250 oC for 24 h followed by 500 oC for 8 h and 300 oC for 10 h followed by 500 oC for 10 h, no tangible difference between lower rate of heating and direct charging was observed in mechanical properties or microstructure. This is believed to be due to the pre-aging steps 250 oC/24 h or 300 oC/10h in the two DA treatments, which create finely distributed precursors thereby leaving no scope for the heating rate to play a role.

scholarly journals Effects of Nano Organoclay and Wax on the Machining Temperature and Mechanical Properties of Carbon Fiber Reinforced Plastics (CFRP)

2019 ◽  
Vol 3 (3) ◽  
pp. 85 ◽  
Author(s):  
El-Ghaoui ◽  
Chatelain ◽  
Ouellet-Plamondon ◽  
Mathieu
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Polycrystalline Diamond ◽  
Fiber Reinforced ◽  
Cfrp Laminates ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced ◽  
Pcd Tools

Carbon fiber reinforced plastics (CFRP) are appreciated for their high mechanical properties and lightness. Due to their heterogeneous nature, CFRP machining remains delicate. Damages are caused on the material and early tool wear occurs. The present study aims to evaluate the effects of fillers on CFRP machinability and mechanical behavior. CFRP laminates were fabricated by the vacuum assisted resin transfer molding (VARTM) process, using a modified epoxy resin. Three fillers (organoclay, hydrocarbon wax, and wetting agent) were mixed with the resin prior to the laminate infusion. Milling tests were performed with polycrystalline diamond (PCD) tools, equipped with thermocouples on their teeth. Machinability was then studied through the cutting temperatures and forces. Tensile, flexural, and short-beam tests were carried out on all samples to investigate the effects of fillers on mechanical properties. Fillers, especially wax, allowed us to observe an improvement in machinability. The best improvement was observed with 1% wax and 2% organoclay, which allowed a significant decrease in the cutting forces and the temperatures, and no deteriorations were seen on mechanical properties. These results demonstrate that upgrades to CFRP machining through the addition of nanoclays and wax is a path to explore.

scholarly journals Thermal Decomposition Kinetic Study of Non-Recyclable Paper and Plastic Waste by Thermogravimetric Analysis

2021 ◽  
Vol 5 (3) ◽  
pp. 54
Author(s):  
Ahmad Mohamed S. H. Al-Moftah ◽  
Richard Marsh ◽  
Julian Steer
Keyword(s):  
Power Generation ◽  
Thermal Decomposition ◽  
Thermogravimetric Analysis ◽  
Thermal Treatment ◽  
Solid Waste ◽  
Heating Rate ◽  
Heating Rates ◽  
Exponential Factor ◽  
Model Free ◽  
Treatment Processes

The global net emissions of the Kyoto Protocol greenhouse gases (GHG), such as carbon dioxide (CO2), fluorinated gases, methane (CH4), and nitrous oxide (N2O), remain substantially high, despite concerted efforts to reduce them. Thermal treatment of solid waste contributes at least 2.8–4% of the GHG in part due to increased generation of municipal solid waste (MSW) and inefficient treatment processes, such as incineration and landfill. Thermal treatment processes, such as gasification and pyrolysis, are valuable ways to convert solid materials, such as wastes into syngas, liquids, and chars, for power generation, fuels, or for the bioremediation of soils. Subcoal™ is a commercial product based on paper and plastics from the source segregated waste that is not readily recyclable and that would otherwise potentially find its way in to landfills. This paper looks at the kinetic parameters associated with this product in pyrolysis, gasification, and combustion conditions for consideration as a fuel for power generation or as a reductant in the blast furnace ironmaking process. Thermogravimetric Analysis (TGA) in Nitrogen (N2), CO2, and in air, was used to measure and compare the reaction kinetics. The activation energy (Ea) and pre-exponential factor A were measured at different heating rates using non-isothermal Ozawa Flynn Wall and (OFW) and Kissinger-Akahira-Sonuse (KAS) model-free techniques. The TGA curves showed that the thermal degradation of Subcoal™ comprises three main processes: dehydration, devolatilization, and char and ash formation. In addition, the heating rate drifts the devolatilization temperature to a higher value. Likewise, the derivative thermogravimetry (DTG) results stated that Tm degradation increased as the heating rate increased. Substantial variance in Ea was noted between the four stages of thermal decomposition of Subcoal™ on both methods. The Ea for gasification reached 200.2 ± 33.6 kJ/mol by OFW and 179.0 ± 31.9 kJ/mol by KAS. Pyrolysis registered Ea values of 161.7 ± 24.7 kJ/mol by OFW and 142.6 ± 23.5 kJ/mol by KAS. Combustion returned the lowest Ea values for both OFW (76.74 ± 15.4 kJ/mol) and KAS (71.0 ± 4.4 kJ/mol). The low Ea values in combustion indicate shorter reaction time for Subcoal™ degradation compared to gasification and pyrolysis. Generally, TGA kinetics analysis using KAS and OFW methods show good consistency in evaluating Arrhenius constants.

Effect of the Annealing Conditions on the Microstructure and Mechanical Properties of a 0.04% C Al Killed Steel

2007 ◽  
Vol 539-543 ◽  
pp. 4208-4213
Author(s):  
Jacobo J. Cardozo ◽  
A.L. Rivas ◽  
R. Colas
Keyword(s):  
Mechanical Properties ◽  
Heating Rate ◽  
Deep Drawing ◽  
Heating Temperature ◽  
Grain Structure ◽  
Major Influence ◽  
Heating Rates ◽  
Annealing Conditions ◽  
Static Annealing ◽  
Initial Heating

The present investigation evaluates the effect of static annealing variables on the grain structure and mechanical properties of a 0.04 %C-Al killed steel. The experimental variables selected were the heating rate and the initial heating temperature. The results showed that an increase in the initial heating temperature and heating rates inferior to 500°C and 100°C/h, respectively, do not have a major influence in the grain structure of the material. These annealing conditions lead to a full "pancake" type of microstructure of the recrystallized ferrite grain, and as consequence, the mechanical properties of the material are in the intervals required for deep drawing applications.

Experimental investigation of interlaminar mechanical properties on carbon fiber stitched CFRP laminates

2007 ◽  
Vol 16 (2) ◽  
pp. 95-113 ◽  
Author(s):  
Yutaka Iwahori ◽  
Takashi Ishikawa ◽  
Naoyuki Watanabe ◽  
Akira Ito ◽  
Yoichi Hayashi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Experimental Investigation ◽  
Carbon Fiber ◽  
Cfrp Laminates

Physical and Mechanical Properties of Fired Clay Bricks Incorporated with Cigarette Butts: Comparison between Slow and Fast Heating Rates

2013 ◽  
Vol 421 ◽  
pp. 201-204
Author(s):  
Aeslina binti Abdul Kadir ◽  
Abbas Mohajerani
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Heating Rate ◽  
Initial Rate ◽  
Physical And Mechanical Properties ◽  
Slow Heating ◽  
Firing Process ◽  
Heating Rates ◽  
Fast Heating ◽  
Rate Of Absorption

In general, firing process in brick manufacturing could affect the properties, colours and appearance of the brick. The main purpose of this study was to evaluate the effect of different heating rates on physical and mechanical properties during the firing of standard bricks and bricks incorporated with cigarette butt (CB). In this investigation, two different heating rates were used: slow heating rate (2oC min-1) and fast heating rate (5oC min-1). Samples were fired in solid forms from room temperature to 1050oC. All bricks were tested for their physical and mechanical properties including compressive strength, initial rate of absorption and density. Higher heating rates decrease compressive strength value but slightly increase the initial rate of absorption and density properties respectively. In conclusion, higher heating rates are able to produce adequate physical and mechanical properties especially for CB Brick.

Sign in / Sign up

Export Citation Format

Share Document