Synthesis of LaMnO3–Diamond Composites and Their Photocatalytic Activity in the Degradation of Weak Acid Red C-3GN

NANO ◽  
2018 ◽  
Vol 13 (10) ◽  
pp. 1850121 ◽  
Author(s):  
Hao Huang ◽  
Benqian Lu ◽  
Yuanyuan Liu ◽  
Xeuqian Wang ◽  
Jie Hu
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Active Sites ◽  
Sol Gel ◽  
Peak Position ◽  
Weak Acid ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Excellent Photocatalytic Activity ◽  
The Fourier Transform

In this study, a series of LaMnO3–diamond composites with varied LaMnO3 mass contents supported on micro-diamond have been synthesized using a sol–gel method. The as-prepared composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy and the Fourier transform infrared spectra (FTIR). Meanwhile, the photocatalytic performances were also tested by photoluminescence (PL) spectroscopy, ultraviolet–visible diffuse reflection spectra (UV-Vis DRS) and the degradation of weak acid red C-3GN (RC-3GN). Results show that the peak position of LaMnO3 is shifted to low angle after the introduction of diamond, and perovskite particles uniformly distributed on the surface of diamond, forming a network structure, which can increase the active sites and the absorption of dye molecules. When the mass ratio of LaMnO3 and diamond is 1:2 (LMO–Dia-2), the composite shows the most excellent photocatalytic activity. This result offers a sample route to enlarge the range of the application of micro-diamond and provide a new carrier for perovskite photocatalysts.

scholarly journals Photocatalytic Activity of Nickel Doped CoO Nanocomposite for the Degradation of Azure A Dye

2020 ◽  
Vol 33 (1) ◽  
pp. 240-244
Author(s):  
Nirmal Singh ◽  
Avinash Kumar Rai ◽  
Ritu Vyas ◽  
Rameshwar Ameta
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Degradation Rate ◽  
Dye Degradation ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Azure A ◽  
Transmission Electron ◽  
Working Parameters

Nanocrystalline cobalt(II) oxide doped with nickel was prepared using the sol-gel method and employed as a photocatalyst for azure A dye degradation under visible light. The prepared photocatalyst was analyzed using energy-dispersive X-ray (EDX) spectroscopy, field emission scanning electron microscopy (FESEM), Fourier-transform infrared (FTIR), X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) techniques. The photocatalytic activity of Ni-doped CoO under different working parameters, like concentration, pH, dosage (Ni-doped and undoped CoO), light intensity for the degradation of azure A dye was also optimzed. It was observed that the dye degradation rate improved after doping. Approximately 76% and 85% of azure A dye was degraded within 90 min through undoped and Ni-doped CoO, respectively.

scholarly journals Composite Magnetic Photocatalyst Bi5O7I/MnxZn1−xFe2O4: Hydrothermal-Roasting Preparation and Excellent Photocatalytic Activity

Nanomaterials ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 118 ◽  
Author(s):  
Hailong Wang ◽  
Longjun Xu ◽  
Chenglun Liu ◽  
Yuan Lu ◽  
Qi Feng ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Energy Gap ◽  
X Ray Diffraction ◽  
Orthorhombic Crystal ◽  
Magnetic Photocatalyst ◽  
Transmission Electron ◽  
Excellent Photocatalytic Activity ◽  
Average Recovery Rate

A new composite magnetic photocatalyst, Bi5O7I/MnxZn1−xFe2O4, prepared by a hydrothermal-roasting method was studied. The photocatalytic properties of Bi5O7I/MnxZn1−xFe2O4 were evaluated by degradation of Rhodamine B (RhB) under simulated sunlight irradiation, and the structures and properties were characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), ultraviolet-visible light (UV-Vis) diffuse reflectance spectra (DRS), and a vibrating sample magnetometer (VSM). The results indicated that Bi5O7I/MnxZn1−xFe2O4 was an orthorhombic crystal, which was similar to that observed for Bi5O7I. Bi5O7I/MnxZn1−xFe2O4 consisted of irregularly shaped nanosheets that were 40–60 nm thick. The most probable pore size was 24.1 nm and the specific surface area was 7.07 m2/g. Bi5O7I/MnxZn1−xFe2O4 could absorb both ultraviolet and visible light, and the energy gap value was 3.22 eV. The saturation magnetization, coercivity and residual magnetization of Bi5O7I/MnxZn1−xFe2O4 were 3.9 emu/g, 126.6 Oe, and 0.7 emu/g respectively, which could help Bi5O7I/MnxZn1−xFe2O4 be separated and recycled from wastewater under the action of an external magnetic field. The recycling experiments revealed that the average recovery rate of the photocatalyst was 90.1%, and the photocatalytic activity was still more than 81.1% after five cycles.

The effect of TiO2addition on the preparation and phase transformation for precursor β-spodumene powders

1994 ◽  
Vol 9 (9) ◽  
pp. 2290-2297 ◽  
Author(s):  
Moo-Chin Wang
Keyword(s):  
Electron Microscopy ◽  
Phase Transformation ◽  
Sol Gel ◽  
Peak Position ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Amorphous Powders ◽  
Lower Temperature ◽  
Dta Curves ◽  
A Minor

Fine β-spodumene-type amorphous powders were obtained through sol-gel techniques using Si(OC2H5)4, Al (OC2H5)3, LiOCH3, and Ti(OC2H5)4as the starting metal alkoxides. Differential thermal analysis (DTA), x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electron diffraction (ED) analysis were utilized to study the phase transformation behavior of the LAST gels. The viscosity of the LAST solution increased abruptly at longer time when the TiO2content was increased. As the TiO2content was increased, the peak position of β-spodumene phase formation in DTA curves was shifted to a lower temperature. For calcination of LAST gels at 800°-1200 °C, the crystallized phases are composed of the major phase of β-spodumene and a minor phase of rutile (TiO2). Unlike earlier studies, heating the dried LAST gels from 800 °C to 1200 °C did not show β-eucryptite, nor found γ-spodumene.

scholarly journals One-Step Synthesis of b-N-TiO2/C Nanocomposites with High Visible Light Photocatalytic Activity to Degrade Microcystis aeruginosa

Catalysts ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 579
Author(s):  
Xu Zhang ◽  
Min Cai ◽  
Naxin Cui ◽  
Guifa Chen ◽  
Guoyan Zou ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Chlorophyll A ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Paramagnetic Resonance ◽  
X Ray ◽  
Transmission Electron ◽  
One Step

Black TiO2 with doped nitrogen and modified carbon (b-N-TiO2/C) were successfully prepared by sol-gel method in the presence of urea as a source of nitrogen and carbon. The photocatalysts were characterized by field emission scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman, electron paramagnetic resonance (EPR), and UV-vis diffuse reflectance spectra (DRS). The doped nitrogen, introduced defects, and modified carbon played a synergistic role in enhancing photocatalytic activity of b-N-TiO2/C for the degradation of chlorophyll-a in algae cells. The sample, with a proper amount of phase composition and oxygen vacancies, showed the highest efficiency to degrade chlorophyll-a, and the addition of H2O2 promoted this photocatalysis degradation. Based on the trapping experiments and electron spin resonance (ESR) signals, a photocatalytic mechanism of b-N-TiO2/C was proposed. In the photocatalytic degradation of chlorophyll-a, the major reactive species were identified as OH and O2−. This research may provide new insights into the photocatalytic inactivation of algae cells by composite photocatalysts.

Few-Layered MoS2 Nanostructures for Highly Efficient Visible Light Photocatalysis

NANO ◽  
2016 ◽  
Vol 11 (10) ◽  
pp. 1650114 ◽  
Author(s):  
Dan Li ◽  
Jianwei Li ◽  
Caiqin Han ◽  
Xinsheng Zhao ◽  
Haipeng Chu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Electrochemical Impedance Spectra ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Hole Pair

Few-layered MoS2 nanostructures were successfully synthesized by a simple hydrothermal method without the addition of any catalysts or surfactants. Their morphology, structure and photocatalytic activity were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, electrochemical impedance spectra and UV-Vis absorption spectroscopy, respectively. These results show that the MoS2 nanostructures synthesized at 180[Formula: see text]C exhibit an optimal visible light photocatalytic activity (99%) in the degradation of Rhodamine B owing to the relatively easier adsorption of pollutants, higher visible light absorption and lower electron–hole pair recombination.

Synthesis, Characterization, and Microwave Absorption Properties of SrFe12O19 Ferrites and FeNi3 Nanoplatelets Composites

2010 ◽  
Vol 148-149 ◽  
pp. 893-896 ◽  
Author(s):  
Ze Yang Zhang ◽  
Xiang Xuan Liu ◽  
You Peng Wu
Keyword(s):  
Electron Microscopy ◽  
Microwave Absorption ◽  
Composite Coatings ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Absorption Properties ◽  
Filling Fraction ◽  
Microwave Absorption Properties ◽  
Phase Reduction ◽  
Transmission Electron

M-typical SrFe12O19 ferrites and FeNi3 nanoplatelets were successfully prepared by the sol-gel method and solution phase reduction method, respectively. The crystalline and morphology of particles were studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The composite coatings with SrFe12O19 ferrites and FeNi3 nanoplatelets in polyvinylchloride matrix were prepared. The microwave absorption properties of these coatings were investigated in 2-18GHz frequency range. The results showed that the M-typical SrFe12O19 ferrites and FeNi3 nanoplatelets were obtained and they presented irregular sheet shapes. With the increase of the coating thickness, the absorbing peak value moves to the lower frequency. The absorbing peak values of the wave increase along with the increasing of the content of FeNi3 nanoplatelets filling fraction. When 40% SrFe12O19 ferrites is doped with 20% mass fraction FeNi3 nanoplatelets to prepare composite with 1.5mm thickness, the maximum reflection loss is -24.8 dB at 7.9GHz and the -10 dB bandwidth reaches 3.2GHz.

scholarly journals Magnetic PbFe12O19-TiO2 nanocomposites and their photocatalytic performance in the removal of toxic pollutants

2018 ◽  
Vol 41 (3-4) ◽  
pp. 53-62 ◽  
Author(s):  
Behnaz Lahijani ◽  
Kambiz Hedayati ◽  
Mojtaba Goodarzi
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Performance ◽  
Sol Gel ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Gel Method ◽  
Sol Gel Method ◽  
Photocatalytic Effect ◽  
Transmission Electron ◽  
Ultraviolet Light Irradiation

Abstract In this work, the PbFe12O19 nanoparticles were prepared by the simple and optimized precipitation method with different organic surfactants and capping agents. In the next step, the TiO2 nanoparticles were synthesized using the sol-gel method. At the final step, the PbFe12O19-TiO2 nanocomposites were prepared via the sol-gel method. The effect of the precipitating agent on the morphology and particle size of the products was investigated. The prepared products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and Fourier transform infrared spectroscopy. The results obtained by the vibrating sample magnetometer show the magnetic properties of the ferrite nanostructures. The photocatalytic effect of the PbFe12O19-TiO2 nanocomposite on the elimination of the azo dyes (acid black, acid violet and acid blue) under ultraviolet light irradiation was evaluated. The results indicate that the prepared nanocomposites have acceptable magnetic and photocatalytic performance.

scholarly journals Oxide-Clay Mineral as Photoactive Material for Dye Discoloration

Minerals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 132
Author(s):  
Maicon O. Miranda ◽  
Bartolomeu Cruz Viana ◽  
Luzia Maria Honório ◽  
Pollyana Trigueiro ◽  
Maria Gardênnia Fonseca ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Clay Mineral ◽  
Uv Light ◽  
High Photocatalytic Activity ◽  
X Ray Diffraction ◽  
Sem Images ◽  
Zirconium Oxides ◽  
Transmission Electron ◽  
Palygorskite Clay

Titanium and zirconium oxides (TiO2 and ZrO2, respectively) were obtained from alkoxides hydrolyses, and then deposited into palygorskite clay mineral (Pal) to obtain new materials for photocatalytic applications. The obtained materials were characterized by structural, morphological, and textural techniques. X-ray diffraction (XRD) results confirmed the characteristic peaks of oxides and clay transmission electron microscopy (TEM) and scanning electron microscopy (SEM) images of the modified palygorskite with both oxides showed that the clay was successfully modified by the proposed method. The increase in the specific surface area of the clay occurred when TiO2 and ZrO2 were deposited on the surface. The photocatalytic activity of these materials was investigated using the Remazol Blue anion dye under UV light. The evaluated systems presented high photocatalytic activity, reaching approximately 98% of dye discoloration under light. Thus, TiO2–Pal and ZrO2–TiO2–Pal are promising clay mineral-based photocatalysts.

ZnS/HALLOYSITE NANOCOMPOSITES: SYNTHESIS, CHARACTERIZATION AND ENHANCED PHOTOCATALYTIC ACTIVITY

2013 ◽  
Vol 06 (02) ◽  
pp. 1350013 ◽  
Author(s):  
YI ZHANG ◽  
HUAMING YANG
Keyword(s):  
Photocatalytic Activity ◽  
Active Sites ◽  
Uv Light ◽  
Halloysite Nanotubes ◽  
Narrow Particle Size Distribution ◽  
Zns Nanoparticles ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Eosin B ◽  
Excellent Photocatalytic Activity

Zinc sulfide (ZnS) nanoparticles are successfully deposited on the surface of natural halloysite nanotubes (HNTs) to produce ZnS /HNTs nanocomposites. The samples are characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, ultraviolet-visible (UV-vis) spectroscopy and photoluminescence (PL) analysis. The results indicate that ZnS nanoparticles are uniformly attached on the surface of HNTs with narrow particle size distribution center at ~10 nm, and are prevented from aggregation by HNTs and expose more active sites. ZnS /HNTs show excellent photocatalytic activity for the degradation of eosin B under UV light, better than pure ZnS and HNTs, indicating its potential application in the field of environmental protection. The mechanism for photocatalytic activity enhancement is also investigated.

Sign in / Sign up

Export Citation Format

Share Document