scholarly journals Effect of Blade Profile on the Performance of Wells Turbine under Unidirectional Sinusoidal and Real Sea Flow Conditions

2007 ◽  
Vol 2007 ◽  
pp. 1-9 ◽  
Author(s):  
A. Thakker ◽  
R. Abdulhadi
Keyword(s):  
Unsteady Flow ◽  
Numerical Results ◽  
Blade Profile ◽  
Flow Conditions ◽  
Wells Turbine ◽  
Hysteretic Characteristics ◽  
The One ◽  
Good Agreement

This paper presents the effect of blade profile and rotor solidity on the performance of Wells turbine operating under unidirectional unsteady flow conditions. In the study, four kinds of blade profile were selected, that is, NACA0020, NACA0015, CA9, and HSIM 15-262123-1576. The experiments have been carried out for two solidities,σ= 0.48 andσ= 0.64, under sinusoidal and irregular unsteady flow conditions based on Irish waves (site2). As a result, it was found that the preferable rotor geometry is the one with blade profile of CA9 with solidityσ= 0.64. In addition, the effect of blade profile and rotor solidity on hysteretic characteristics of the turbine has been clarified experimentally and it was found to be in good agreement qualitatively when compared to numerical results (Setoguchi et al. (2003)).

Wells Turbines With 3-Dimensional Blades: The Performance Under Unsteady Flow Conditions

2015 ◽  
Author(s):  
Manabu Takao ◽  
Katsuya Takasaki ◽  
Tomohiro Tsunematsu ◽  
Miah Md. Ashraful Alam ◽  
Toshiaki Setoguchi
Keyword(s):  
Unsteady Flow ◽  
Flow Separation ◽  
Blade Profile ◽  
Wave Energy Conversion ◽  
Flow Conditions ◽  
Suction Surface ◽  
Wells Turbine ◽  
3 Dimensional ◽  
Profile Changes ◽  
The Mean

The effect of the 3-dimentional (3D) blade on the turbine characteristics of Wells turbines for wave energy conversion has been investigated numerically by a quasi-steady analysis under unsteady flow conditions in this study in order to improve the peak mean efficiency characteristics. The aim of use of the 3D blade is to prevent flow separation on the suction surface near the tip. The chord length is constant in the radius and the blade profile changes gradually from the mean radius to the tip. The proposed blade profiles in the study are NACA0015 from the hub to mean radius and NACA0025 at the tip. The performance of the Wells turbine with 3D blades has been compared with those of the original Wells turbine, i.e., the turbine with 2-dimentional blades. As a result, it was concluded that although the peak mean efficiency of a Wells turbine can be improved by the use of the proposed 3D blade, its blade does not overcome the stall characteristic.

scholarly journals Study of Unsteady Flow in a Heat Exchanger by the Method of Characteristics

1992 ◽  
Vol 114 (4) ◽  
pp. 459-463 ◽  
Author(s):  
Yuan Mao Huang
Keyword(s):  
Heat Exchanger ◽  
Unsteady Flow ◽  
Transfer Rate ◽  
Method Of Characteristics ◽  
Governing Equations ◽  
One Dimensional ◽  
The Method Of Characteristics ◽  
Improvement Factor ◽  
The One ◽  
Good Agreement

The one-dimensional, unsteady flow in an air-to-air heat exchanger is studied. The governing equations are derived and the method of characteristics with the uniform interval scheme is used in the analysis. The effect of the fin improvement factor on the air temperature in the heat exchanger and the heat transfer rate of the heat exchanger, and air properties in the heat exchanger are analyzed. The numerical results are compared and show good agreement with the available data.

CFD Analysis of Stall in a Wells Turbine

2018 ◽  
Author(s):  
Kellis Kincaid ◽  
David W. MacPhee
Keyword(s):  
Source Code ◽  
Turbulence Models ◽  
Ocean Waves ◽  
Cfd Analysis ◽  
Oscillating Water Column ◽  
Blade Profile ◽  
Flow Conditions ◽  
Wells Turbine ◽  
Sst Model ◽  
Blade Shape

The Wells turbine is a self-rectifying device that employs a symmetrical blade profile, and is often used in conjunction with an oscillating water column to extract energy from ocean waves. The effects of solidity, angle of attack, blade shape and many other parameters have been widely studied both numerically and experimentally. To date, several 3-D numerical simulations have been performed using commercial software, mostly with steady flow conditions and employing various two-equation turbulence models. In this paper, the open source code Open-FOAM is used to numerically study the performance characteristics of a Wells turbine using a two-equation turbulence model, namely the Menter SST model, in conjunction with a transient fluid solver.

The Flow Phenomena and the Non-Uniform Filling of the Unvulcanized Rubber in Process of Filling

2009 ◽  
Author(s):  
Shintarou Sakai ◽  
Toru Shigemitsu ◽  
Junichiro Fukutomi ◽  
Tsukasa Matsuoka
Keyword(s):  
Numerical Analysis ◽  
Narrow Channel ◽  
Numerical Results ◽  
Flow Conditions ◽  
Flow Phenomena ◽  
Rubber Product ◽  
Vulcanization Process ◽  
Filling State ◽  
Optimum Flow ◽  
Good Agreement

Rubber products like oil seal are produced by vulcanization molding and the vulcanization molding of rubber product is performed by past experience, trial and error. It is important issues to decrease the product cost, reduce defective products and solve the environmental problems by saving natural resources. If the vulcanization moldings of rubber products are reappeared by computer simulation, it is very useful and it could contribute to solve the above problems. In order to reduce surplus rubber and defective products, numerical analysis of flow phenomena of unvulcanized rubber was performed using commercial software FIDAP. In several types of rubber mold model, the numerical analysis was conducted taken the characteristic of visco-elasticity fluid obtained by an experiment without considering the effect of heat. And experiments were conducted for the comparison of numerical results and actual phenomena. In the experiment, vulcanization process was stopped by arbitrary interval. Then the filling state and the shape of the rubber at each interval are observed in numerical and experiment results. The results showed that the filling state of numerical results represented good agreement with the experimental results. And it was clarified from the numerical analysis that shear stress increased when the unvulcanized rubber flowed in a narrow channel and there was the relation between pressure and velocity. In the present paper, the flow phenomena under the condition of the compression molding are shown and the optimum flow conditions are discussed from the numerical results. Furthermore mechanism of occurrence of defective products is considered with the experimental and the numerical results.

scholarly journals Performance characterization of a wells turbine under unsteady flow conditions

2019 ◽  
Author(s):  
Marco Torresi ◽  
Michele Stefanizzi ◽  
Francesco Fornarelli ◽  
Luana Gurnari ◽  
Pasquale Giuseppe Fabio Filianoti ◽  
...  
Keyword(s):  
Unsteady Flow ◽  
Flow Conditions ◽  
Wells Turbine ◽  
Performance Characterization

On the maximal spreading of impacting compound drops

2018 ◽  
Vol 854 ◽  
Author(s):  
H.-R. Liu ◽  
C.-Y. Zhang ◽  
P. Gao ◽  
X.-Y. Lu ◽  
H. Ding
Keyword(s):  
Flow Regime ◽  
Weber Number ◽  
Volume Fraction ◽  
Numerical Results ◽  
Diffuse Interface ◽  
Spreading Dynamics ◽  
The One ◽  
Compound Drops ◽  
The Impact ◽  
Good Agreement

We numerically study the impact of a compound drop on a hydrophobic substrate using a ternary-fluid diffuse-interface method, aiming to understand how the presence of the inner droplet affects the spreading dynamics and maximal spreading of the compound drop. First, it is interesting to see that the numerical results for an impacting pure drop agree well with the universal rescaling of maximal spreading ratio proposed by Lee et al. (J. Fluid Mech., vol. 786, 2016, R4). Second, two flow regimes have been identified for an impacting compound drop: namely jammed spreading and joint rim formation. The maximal spreading ratio of the compound drop is found to depend on the volume fraction of the inner droplet $\unicode[STIX]{x1D6FC}$, the surface tension ratio $\unicode[STIX]{x1D6FE}$, the Weber number and the flow regime. Moreover, we propose a universal rescaling of maximal spreading ratio for compound drops, by integrating the one for pure drops with a corrected Weber number that takes $\unicode[STIX]{x1D6FC}$, $\unicode[STIX]{x1D6FE}$ and the flow regime into account. The predictions of the universal rescaling are in good agreement with the numerical results for impacting compound drops.

Two-Phase Model for Simulating Current-Induced Scour Beneath Subsea Pipelines at Different Initial Elevations

2018 ◽  
Author(s):  
Jun Y. Lee ◽  
Jasmin B. T. McInerney ◽  
Fauzi A. Hardjanto ◽  
Shuhong Chai ◽  
Remo Cossu ◽  
...  
Keyword(s):  
Numerical Results ◽  
Scour Depth ◽  
Flow Conditions ◽  
Eulerian Model ◽  
Two Phase ◽  
Mesh Dependency ◽  
Steady Current ◽  
Equilibrium Scour Depth ◽  
Subsea Pipelines ◽  
Good Agreement

When a subsea pipeline is laid on an uneven seabed, the pipeline can have an initial elevation, potentially compromising its on-bottom stability; scouring due to flow conditions around the pipe can further exacerbate the problem. We assess the capability of the two-phase Eulerian-Eulerian OpenFOAM solver, twoPhaseEulerFoam, in terms of predicting the equilibrium scour depth beneath a pipe at different initial elevations under a steady current for the live bed condition. The predictions were found to be in good agreement with published experimental and numerical results; however, similar to a recent study involving another two-phase Eulerian-Eulerian model, the scour time scale was under-predicted. The predicted equilibrium scour depth was seen to decrease with an increase in the initial pipe elevation. The numerical results were also compared to predictions that were made using previous empirical equations. The most comprehensive equation to date showed a good agreement with the present numerical results. We conclude that this open-source solver, twoPhaseEulerFoam, can be used to predict the equilibrium scour depth beneath subsea pipelines, with short computation times and negligible mesh dependency.

Effect of leakage and blockage on the acoustic behavior of particle filters

2019 ◽  
Vol 67 (6) ◽  
pp. 483-492
Author(s):  
Seonghyeon Baek ◽  
Iljae Lee
Keyword(s):  
Transfer Matrix ◽  
Particle Filters ◽  
Acoustic Analysis ◽  
Transmission Loss ◽  
One Dimensional ◽  
Filter System ◽  
The Difference ◽  
The One ◽  
Analytical Approaches ◽  
Good Agreement

The effects of leakage and blockage on the acoustic performance of particle filters have been examined by using one-dimensional acoustic analysis and experimental methods. First, the transfer matrix of a filter system connected to inlet and outlet pipes with conical sections is measured using a two-load method. Then, the transfer matrix of a particle filter only is extracted from the experiments by applying inverse matrices of the conical sections. In the analytical approaches, the one-dimensional acoustic model for the leakage between the filter and the housing is developed. The predicted transmission loss shows a good agreement with the experimental results. Compared to the baseline, the leakage between the filter and housing increases transmission loss at a certain frequency and its harmonics. In addition, the transmission loss for the system with a partially blocked filter is measured. The blockage of the filter also increases the transmission loss at higher frequencies. For the simplicity of experiments to identify the leakage and blockage, the reflection coefficients at the inlet of the filter system have been measured using two different downstream conditions: open pipe and highly absorptive terminations. The experiments show that with highly absorptive terminations, it is easier to see the difference between the baseline and the defects.

Modeling of mass transfer in biofilms in oscillatory flow conditions using k-ɛ turbulence model

2003 ◽  
Vol 3 (1-2) ◽  
pp. 201-207
Author(s):  
H. Nagaoka ◽  
T. Nakano ◽  
D. Akimoto
Keyword(s):  
Numerical Simulation ◽  
Mass Transfer ◽  
Turbulence Model ◽  
Uptake Rate ◽  
Oscillatory Flow ◽  
Substrate Uptake ◽  
Flow Conditions ◽  
Mass Transfer Mechanism ◽  
Substrate Uptake Rate ◽  
Good Agreement

The objective of this research is to investigate mass transfer mechanism in biofilms under oscillatory flow conditions. Numerical simulation of turbulence near a biofilm was conducted using the low Reynold’s number k-ɛ turbulence model. Substrate transfer in biofilms under oscillatory flow conditions was assumed to be carried out by turbulent diffusion caused by fluid movement and substrate concentration profile in biofilm was calculated. An experiment was carried out to measure velocity profile near a biofilm under oscillatory flow conditions and the influence of the turbulence on substrate uptake rate by the biofilm was also measured. Measured turbulence was in good agreement with the calculated one and the influence of the turbulence on the substrate uptake rate was well explained by the simulation.

scholarly journals Optimization of the flow conditions in the spawning ground of the Chinese sturgeon (Acipenser sinensis) through Gezhouba Dam generating units

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Anyang Huang ◽  
Jinzhong Yao ◽  
Jiazhi Zhu ◽  
Xingchen Gao ◽  
Wei Jiang
Keyword(s):  
Spawning Ground ◽  
Chinese Sturgeon ◽  
Flow Conditions ◽  
Velocity Measurements ◽  
Acipenser Sinensis ◽  
Critically Endangered Species ◽  
Gezhouba Dam ◽  
Opening Mode ◽  
Suitable Area ◽  
Good Agreement

AbstractChinese sturgeon (Acipenser sinensis) is a critically endangered species, and waters downstream from Gezhouba Dam are the only known spawning ground. To optimize the velocity conditions in the spawning ground by controlling the opening mode of Gezhouba Dam generator units, a mathematical model of Chinese sturgeon spawning ground was established in FLOW-3D. The model was evaluated with velocity measurements, and the results were determined to be in good agreement. By inverting the 2016–2019 field monitoring results, the model shows that the preferred velocity range for Chinese sturgeon spawning is 0.6–1.5 m/s. Velocity fields of different opening modes of the generator units were simulated with identical discharge. The suitable-velocity area was maximal when all units of Dajiang Plant of Gezhouba Dam were open. For discharges below 12,000 m3/s, most of the area was suitable; for discharges above 12,000 m3/s, the suitable area rapidly decreased with increasing discharge. A comparison of suitable areas under high-flow showed that at discharges of 12,000–15,000 m3/s, opening 11–13 units on the left side was optimal. For discharges above 15,000 m3/s, all units should be open. We used these results to recommend a new operation scheme to support the conservation of Chinese sturgeon.

Sign in / Sign up

Export Citation Format

Share Document