scholarly journals Synthesis and Characterization of Boehmite Nanofibers

2008 ◽  
Vol 2008 ◽  
pp. 1-4 ◽  
Author(s):  
Jing Yang ◽  
Ray L. Frost
Keyword(s):  
Emission Spectroscopy ◽  
Analytical Techniques ◽  
Infrared Emission ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
High Quality ◽  
X Ray ◽  
Clear Cut ◽  
Scanning Electron

Boehmite nanofibers of high quality were synthesized through a wet-gel conversion process without the use of a surfactant. The long nanofibers of boehmite with clear-cut edges were obtained by steaming the wet-gel precipitate at 170∘C for 2 days. Analytical techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), infrared emission spectroscopy (IES), as well as Raman spectroscopy were used to characterize the products.

scholarly journals Synthesis and characterization of apatite silicated powders with wet precipitation method

2021 ◽  
Vol 234 ◽  
pp. 00106
Author(s):  
Houda Labjar ◽  
Hassan Chaair
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Analytical Techniques ◽  
Precipitation Method ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wet Precipitation ◽  
Scanning Electron

The synthesis of apatite silicated Ca10(PO4)6-x(SiO4)x(OH)2-x (SiHA) with 0≤x≤2 was investigated using a wet precipitation method followed by heat treatment using calcium carbonate CaCO3 and phosphoric acid H3PO4 and silicon tetraacetate SiC8H20O4 (TEOS) in medium of water ethanol, with three different silicate concentrations. After drying, the samples are ground and then characterized by different analytical techniques like X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR) and Scanning electron Microscopy (SEM) and chemical analysis.

Green Synthesis and Characterization of Hydroxyapatite from Fish Scale Biowaste

2014 ◽  
Vol 695 ◽  
pp. 235-238 ◽  
Author(s):  
Jamali Sukaimi ◽  
Sofiah Hamzah ◽  
Mohd Sabri Mohd Ghazali
Keyword(s):  
Electron Microscopy ◽  
Synthesis And Characterization ◽  
Fish Scale ◽  
X Ray Diffraction ◽  
High Quality ◽  
X Ray ◽  
Different Temperatures ◽  
Scanning Electron

The present study was undertaken to study the effect of calcinate temperature on characteristics of hydroxyapatite synthesized from the fish scale (FHAp). The FHAp calcined at different temperatures starting from 100 up to 300 °C. The structures of FHAP were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction. The analytical results show that the FHAp quality increased as the calcin temperature increased. The FHAp displayed excellent characteristics in term of particle size, morphology and properties and crystalinity after calcined at 300 °C, FHAp 300. From this study, it founded that 300 °C is the lowest calcin temperature could be applied to synthesize high quality of HAp from fish scale biowaste.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

Hydrothermal Synthesis and Characterization of BiFeO3 Polyhedral Crystallites

2012 ◽  
Vol 174-177 ◽  
pp. 508-511
Author(s):  
Lin Lin Yang ◽  
Yong Gang Wang ◽  
Yu Jiang Wang ◽  
Xiao Feng Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

BiFeO3 polyhedrons had been successfully synthesized via a hydrothermal method. The as-prepared products were characterized by power X-ray diffraction (XRD) pattern, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The possible mechanisms for the formation of BiFeO3 polyhedrons were discussed. Though comparison experiments, it was found that the kind of precursor played a key role on the morphology control of BiFeO3 crystals.

Rapid Synthesis and Characterization of CuInS2 Prepared Using Microwave-Assisted Heating

2015 ◽  
Vol 775 ◽  
pp. 143-146
Author(s):  
Ming Kwen Tsai ◽  
Yueh Chien Lee ◽  
Chia Chih Huang ◽  
Sheng Yao Hu ◽  
Kwong Kau Tiong ◽  
...  
Keyword(s):  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Structural And Optical Properties ◽  
Rapid Synthesis ◽  
X Ray ◽  
Sem Image ◽  
Microwave Assisted ◽  
Calcination Treatment ◽  
Scanning Electron

In this work, the CuInS2 nanoparticles are successfully synthesized by microwave-assisted heating technique and further calcined at 400 °C. The morphological, structural, and optical properties of the synthesized CuInS2 nanoparticles are investigated by scanning electron microscope (SEM), X-ray diffraction (XRD), Raman scattering, and transmittance measurement, respectively. The SEM image shows the clear particle shape of the calcined CuInS2 nanoparticles. After calcination treatment, the fundamental (112) peak of the XRD spectrum and a broad Raman peak mixed with chalcopyrite and CuAu structures support the improved crystallinity of the calcined CuInS2 nanoparticles.

Synthesis and Characterization of the PANI/ITO Conducting Nanocomposites

2010 ◽  
Vol 663-665 ◽  
pp. 542-545 ◽  
Author(s):  
Bing Jie Zhu ◽  
Xin Wei Wang ◽  
Mei Fang Zhu ◽  
Qing Hong Zhang ◽  
Yao Gang Li ◽  
...  
Keyword(s):  
Doping Concentration ◽  
In Situ Polymerization ◽  
Synthesis And Characterization ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
X Ray ◽  
Maximum Conductivity ◽  
Scanning Electron

The PANI/ITO conducting nanocomposites have been synthesized by in-situ polymerization. The obtained nanocomposites were characterized by X-ray diffraction pattern, scanning electron microscopy and Fourier transform infrared. Electrical conductivity measurements on the samples pressed into pellets showed that the maximum conductivity attained 2.0 ± 0.05 S/cm for PANI/ITO nanocomposites, at ITO doping concentration of 10 wt%. The results of the present work may provide a simple, rapid and efficient approach for preparing PANI/ITO nanocomposites.

Synthesis and characterization of homogeneous lead-substituted tin oxide with the (110) face of rutile structure

2000 ◽  
Vol 15 (10) ◽  
pp. 2076-2079
Author(s):  
Chika Nozaki ◽  
Takashi Yamada ◽  
Kenji Tabata ◽  
Eiji Suzuki
Keyword(s):  
Electron Microscopy ◽  
Tin Oxide ◽  
Photoelectron Spectroscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Rutile Structure ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Synthesis of a rutile-type lead-substituted tin oxide with (110) face was investigated. The characterization was performed by x-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive x-ray spectroscopy, infrared spectroscopy, x-ray photoelectron spectroscopy, and Brunauer–Emmett–Teller surface area measurements. The homogeneous rutile-type lead-substituted tin oxide was obtained until 4.1 mol% of tin was substituted with lead. The surface of obtained oxide had a homogeneously lead-substituted (110) face.

Synthesis and Characterization of Y2O3 Nanoflowers

2012 ◽  
Vol 465 ◽  
pp. 76-79 ◽  
Author(s):  
Shuang Zhan ◽  
Xia Li
Keyword(s):  
Fourier Transform ◽  
Phase Composition ◽  
Electron Microscope ◽  
Synthesis And Characterization ◽  
The Novel ◽  
X Ray Diffraction ◽  
Facile Hydrothermal Method ◽  
X Ray ◽  
Scanning Electron

The novel Y2O3 nanoflowers were synthesized through a facile hydrothermal method without using any catalyst or template. The phase composition and the microstructure of as-prepared products were characterized by field emission scanning electron microscope (FE-SEM), X-ray diffraction (XRD) as well as Fourier transform infrared spectrum. The formation mechanism for the Y2O3 flowers has been proposed.

Preparation and Electrical Characterization of Poly(Aniline) NanoClay Composites

2015 ◽  
Vol 34 (4) ◽  
Author(s):  
Esma Ahlatcioǧlu ◽  
Bahire Filiz şenkal ◽  
Mustafa Okutan
Keyword(s):  
Electrical Characterization ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Inorganic Hybrid ◽  
X Ray ◽  
Ft Ir ◽  
Doped Polyaniline ◽  
Poly Aniline ◽  
Scanning Electron

AbstractIn this work, synthesis and characterization of composite materials based on NanoClay(NC) and boric acid doped PolyAniline (PANI) is studied. PANI was successfully incorporated into NC to form PANI-NC composites. The resulting organic-inorganic hybrid material, PANI-NC was characterized by various physicochemical techniques. Formation of PANI inside the clay tactoid has been confirmed by X-ray diffraction studies (XRD), scanning electron microscope (SEM) and FT-IR. Also, conductivity and physical properties of the PANI-NC composites were investigated.

Synthesis and Characterization of Star-Like Copper Oxide (CuO) with Submicrometer Sizes

2012 ◽  
Vol 465 ◽  
pp. 186-191
Author(s):  
Shou Long Gong ◽  
Fang Lin Du
Keyword(s):  
Electron Microscopy ◽  
Synthesis And Characterization ◽  
Simple Liquid ◽  
Liquid Phase Deposition ◽  
Monoclinic Structure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Star-like CuO with submicrometer sizes was fabricated via a simple liquid-phase deposition with the assistant of PVP and Na2MoO4. The as-prepared CuO have been characterized by X-ray diffraction(XRD) and scanning electron microscopy (SEM). The results showed that the as-prepared CuO owned monoclinic structure, the concentrations of PVP, Na2MoO4 and NaOH are very important to the morphology of CuO. The quality of PVP impacts the formation of thin flakes on the skeletons. Meanwhile, the growth of dendritic skeletons was depended on the addition of Na2MoO4, and the effect of NaOH is to control the dimension of CuO structure.

Sign in / Sign up

Export Citation Format

Share Document