scholarly journals Development of a Low-Cost SIA-Based Analyser for Water Samples

2011 ◽  
Vol 2011 ◽  
pp. 1-7
Author(s):  
Moisés Knochen ◽  
Alejandro Caamaño ◽  
Heinkel Bentos
Keyword(s):  
Flow System ◽  
Detection System ◽  
Low Cost ◽  
Visual Basic ◽  
Sequential Injection Analysis ◽  
Simultaneous Methods ◽  
Total Cost ◽  
Figures Of Merit ◽  
Photometric Detection ◽  
Data Acquisition And Processing

An automated multiparametric water analyser was developed and evaluated. The system was based on Sequential Injection Analysis and featured a photometric detection system comprising a tricolour RGB LED source and a photodiode. A program compiled in Visual Basic was used to control the SIA flow system, the LEDs, and the data acquisition and processing. The program loads and executes methods written in ASCII and stored as text files. The system was capable of handling up to four methods simultaneously. When used to carry out methods based on the APHA standard methods, the figures of merit obtained were considered satisfactory for the purpose. The total cost was under US $4600. It was concluded that the analyser is appropriate for routine use and has potential for an increased number of simultaneous methods and for enhanced capabilities if new versions of the software are developed.

Study of the film formation process in liquid-liquid extraction flow injection analysis

1991 ◽  
Vol 56 (6) ◽  
pp. 1228-1237 ◽  
Author(s):  
Vlastimil Kubáň
Keyword(s):  
Flow System ◽  
Detection System ◽  
Film Formation ◽  
Liquid Extraction ◽  
Photometric Detection ◽  
Liquid Liquid Extraction ◽  
Teflon Tube ◽  
Continuous Stream ◽  
Computer Controlled ◽  
Segmented Volume

The behaviour of a thin film of an organic solvent on the walls of the extraction coil in a continuous liquid-liquid extraction flow system was studied using a computer-controlled fast-recording on-tube photometric detection system (approx. 3 ms time resolution). A single-loop injector was employed to introduce precise, reproducible volumes (Sr < 2%) of one phase into the continuous stream of the other as a segmented volume standard. The film thickness Df, ranging from 1 to 20 μm for a 0.7 mm teflon tube, was calculated from the segment lengthening at a different chloroform flow rates and was found to obey a polynominal dependence on the linear flow rate, df = f(uα), where α < 1.

scholarly journals Sensor Networks for Structures Health Monitoring: Placement, Implementations, and Challenges—A Review

Vibration ◽  
2021 ◽  
Vol 4 (3) ◽  
pp. 551-584
Author(s):  
Samir Mustapha ◽  
Ye Lu ◽  
Ching-Tai Ng ◽  
Pawel Malinowski
Keyword(s):  
Sensor Networks ◽  
Health Monitoring ◽  
Data Transmission ◽  
System Integration ◽  
Structural Integrity ◽  
Low Cost ◽  
Data Communication ◽  
Total Cost ◽  
Design And Optimization ◽  
Successful Case

The development of structural health monitoring (SHM) systems and their integration in actual structures has become a necessity as it can provide a robust and low-cost solution for monitoring the structural integrity of and the ability to predict the remaining life of structures. In this review, we aim at focusing on one of the important issues of SHM, the design, and implementation of sensor networks. Location and number of sensors, in any SHM system, are of high importance as they impact the system integration, system performance, and accuracy of assessment, as well as the total cost. Hence we are interested in shedding the light on the sensor networks as an essential component of SHM systems. The review discusses several important parameters including design and optimization of sensor networks, development of academic and commercial solutions, powering of sensors, data communication, data transmission, and analytics. Finally, we presented some successful case studies including the challenges and limitations associated with the sensor networks.

Face recognition in an intelligent door lock with ResNet model based on deep learning

2021 ◽  
pp. 1-11
Author(s):  
Suphawimon Phawinee ◽  
Jing-Fang Cai ◽  
Zhe-Yu Guo ◽  
Hao-Ze Zheng ◽  
Guan-Chen Chen
Keyword(s):  
Face Recognition ◽  
Detection System ◽  
Low Cost ◽  
Ease Of Use ◽  
Raspberry Pi ◽  
Training Methods ◽  
Graphics Recognition ◽  
Face Images ◽  
The Face ◽  
Door Lock

Internet of Things is considerably increasing the levels of convenience at homes. The smart door lock is an entry product for smart homes. This work used Raspberry Pi, because of its low cost, as the main control board to apply face recognition technology to a door lock. The installation of the control sensing module with the GPIO expansion function of Raspberry Pi also improved the antitheft mechanism of the door lock. For ease of use, a mobile application (hereafter, app) was developed for users to upload their face images for processing. The app sends the images to Firebase and then the program downloads the images and captures the face as a training set. The face detection system was designed on the basis of machine learning and equipped with a Haar built-in OpenCV graphics recognition program. The system used four training methods: convolutional neural network, VGG-16, VGG-19, and ResNet50. After the training process, the program could recognize the user’s face to open the door lock. A prototype was constructed that could control the door lock and the antitheft system and stream real-time images from the camera to the app.

Development of a method for detecting trace metals in aqueous solutions based on the coordination chemistry of hexahydrotriazines

The Analyst ◽  
2015 ◽  
Vol 140 (15) ◽  
pp. 5184-5189 ◽  
Author(s):  
Rudy J. Wojtecki ◽  
Alexander Y. Yuen ◽  
Thomas G. Zimmerman ◽  
Gavin O. Jones ◽  
Hans W. Horn ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Coordination Chemistry ◽  
Trace Metals ◽  
Aqueous Solutions ◽  
Detection System ◽  
Low Cost ◽  
System P ◽  
Chemical Indicator

The detection of trace amounts (<10 ppb) of heavy metals in aqueous solutions is described using hexahydrotriazines as a chemical indicator and a low cost fluorimeter-based detection system.

A Low Cost Knowledge Based System Framework for Design of Bending Die

2013 ◽  
Vol 549 ◽  
pp. 284-291 ◽  
Author(s):  
Deepak Panghal ◽  
Shailendra Kumar
Keyword(s):  
Sheet Metal ◽  
Low Cost ◽  
Visual Basic ◽  
Die Design ◽  
Small Scale ◽  
Production Rules ◽  
System Framework ◽  
Knowledge Based System ◽  
Sheet Metal Parts ◽  
Knowledge Based

This paper presents a low cost knowledge based system (KBS) framework for design of bending die. Considerations for development of KBS are discussed at some length. The proposed framework divides the task of development of expert system into different modules for major activities of bending die design. The procedure of development of KBS modules is also described at length. Production rules for each module are recommended to be coded in the AutoLISP language and designed to be loaded into the prompt area of AutoCAD or through user interface created using Visual Basic. Each module of the proposed framework is user interactive. Development of one module of the proposed framework is also described at length. This module is capable to assess manufacturability of bending sheet metal parts. An illustrative example is also included to demonstrate the usefulness of this module. The proposed system framework is flexible enough to accommodate new acquired knowledge. As the proposed system is implementable on a PC having AutoCAD software, therefore its low cost of implementation makes it affordable even by small scale sheet metal industries.

Design of a low-cost detection system for laser-induced plasma spectroscopy

1999 ◽  
Vol 70 (9) ◽  
pp. 3519-3522 ◽  
Author(s):  
R. E. Neuhauser ◽  
B. Ferstl ◽  
C. Haisch ◽  
U. Panne ◽  
R. Niessner
Keyword(s):  
Detection System ◽  
Low Cost ◽  
Plasma Spectroscopy ◽  
Laser Induced Plasma

The Hardware Design and Implementation of Liquid Level Detection System for Lead-Acid Battery

2013 ◽  
Vol 860-863 ◽  
pp. 2850-2854 ◽  
Author(s):  
Ya Jun Bi ◽  
Hong Fei Li
Keyword(s):  
Detection System ◽  
Low Cost ◽  
Liquid Level ◽  
Lead Acid Battery ◽  
Infrared Transmission ◽  
Wireless Data ◽  
Linear Ccd ◽  
Infrared Technology ◽  
Liquid Level Detection ◽  
Lead Acid

The hardware structure of a liquid level detection system for lead-acid battery was briefly introduced. The system adopts AT89C51 MCU as host module, combined with display storage, extended storage and the watch dog technology. The slave module adopts AT89C2051 MCU, which driver the linear CCD to realize non-contact measurement in acidic and corrosive conditions. The infrared transmission module uses RS-232 serial-to-infrared technology to realize wireless data delivery. The damage due to sensor corrosion could be avoided in this system. Compared with other similar equipments, this system has the advantages of simple structure, small volume, low cost, high measure precision and convenient maintenance.

Sign in / Sign up

Export Citation Format

Share Document