scholarly journals Reduction of Postfire Properties of High-Strength Concrete

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Neno Torić ◽  
Ivica Boko ◽  
Bernardin Peroš
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Ambient Temperature ◽  
Modulus Of Elasticity ◽  
High Strength Concrete ◽  
High Strength ◽  
Maximum Temperature ◽  
Secant Modulus ◽  
Strength Concrete

This paper presents an experimental study of behaviour of high-strength concrete at high temperature. Reduction of the mechanical properties of concrete was determined starting from the period when the concrete specimens were heated to the maximum temperature and cooled down to ambient temperature and the additional 96 hours after the initial cooling of the specimens. The study includes determination of compressive strength, dynamic and secant modulus of elasticity, and stress-strain curves of concrete specimens when exposed to temperature level up to 600°C. The study results were compared with those obtained from other studies, EN 1994-1-2 and EN 1992-1-2. Tests point to the fact that compressive strength of concrete continues to reduce rapidly 96 hours after cooling of the specimens to ambient temperature; therefore indicating that the mechanical properties of concrete have substantial reduction after being exposed to high temperature. The study of the dynamic and secant modulus of elasticity shows that both of the properties are reduced but remain constant during the period of 96 hours after cooling. The level of postfire reduction of compressive strength of the analyzed concrete is substantial and could significantly affect the postfire load bearing capacity of a structure.

Comparison Analysis on the Mechanical Properties of HSC and NSC after the Action of High Temperatures

2014 ◽  
Vol 1014 ◽  
pp. 49-52
Author(s):  
Xiao Ping Su
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
High Temperatures ◽  
High Strength Concrete ◽  
Elasticity Modulus ◽  
Strain Curve ◽  
Peak Stress ◽  
High Strength ◽  
Peak Strain ◽  
Strength Concrete

With the wide application of high strength concrete in the building construction,the risk making concrete subject to high temperatures during a fire is increasing. Comparison tests on the mechanical properties of high strength concrete (HSC) and normal strength concrete (NSC) after the action of high temperature were made in this article, which were compared from the following aspects: the peak stress, the peak strain, elasticity modulus, and stress-strain curve after high temperature. Results show that the laws of the mechanical properties of HSC and NSC changing with the temperature are the same. With the increase of heating temperature, the peak stress and elasticity modulus decreases, while the peak strain grows rapidly. HSC shows greater brittleness and worse fire-resistant performance than NSC, and destroys suddenly. The research and evaluation on the fire-resistant performance of HSC should be strengthened during the structural design and construction on the HSC buildings.

scholarly journals Effect of Locally Available Wheat Straw Ash in Developing High Strength Concrete

2021 ◽  
pp. 19-28
Author(s):  
Muhammad Armaghan Siffat ◽  
Muhammad Ishfaq ◽  
Afaq Ahmad ◽  
Khalil Ur Rehman ◽  
Fawad Ahmad
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Wheat Straw ◽  
High Strength Concrete ◽  
High Strength ◽  
Optimum Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Strength Concrete ◽  
Straw Ash

This study is supervised to assess the characteristics of the locally available wheat straw ash (WSA) to consume as a substitute to the cement and support in enhancing the mechanical properties of concrete. Initially, after incineration at optimum temperature of 800°C for 0.5, the ash of wheat straw was made up to the desirable level of fineness by passing through it to the several grinding cycles. Subsequently, the X-ray fluorescence (XRF) along with X-ray diffraction (XRD) testing conducted on ash of wheat straw for the evaluation its pozzolanic potential. Finally, the specimens of concrete were made by consuming 10% and 20% percentages of wheat straw ash as a replacement in concrete to conclude its impact on the compressive strength of high strength concrete. The cylinders of steel of dimensions 10cm diameter x 20cm depth were acquired to evaluate the compressive strength of high strength concrete. The relative outcomes of cylinders made of wheat straw ash substitution presented the slight increase in strength values of the concrete. Ultimately, the C-100 blends and WSA aided cement blends were inspected for the rheology of WSA through FTIR spectroscopy along with Thermogravimetric technique. The conclusions authenticate the WSA potential to replace cement in the manufacturing of the high strength concrete.

Performance Deterioration of High Strength Concrete under Mixed Erosion and Freeze-Thaw Cycling

2010 ◽  
Vol 163-167 ◽  
pp. 1655-1660
Author(s):  
Jian Zhang ◽  
Bo Diao ◽  
Xiao Ning Zheng ◽  
Yan Dong Li
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Mass Loss ◽  
Modulus Of Elasticity ◽  
Dynamic Modulus ◽  
High Strength Concrete ◽  
High Strength ◽  
Freeze Thaw ◽  
Strength Concrete ◽  
Dynamic Modulus Of Elasticity

The mechanical properties of high strength concrete(HSC) were experimentally investigated under mixed erosion and freeze-thaw cycling according to ASTM C666(Procedure B), the erosion solution was mixed by weight of 3% sodium chloride and 5% sodium sulfate. The mass loss, relative dynamic modulus of elasticity, compressive strength, elastic modulus and other relative data were measured. The results showed that with the increasing number of freeze-thaw cycles, the surface scaled more seriously; the mass loss, compressive strength and elastic modulus continued to decrease; the relative dynamic modulus of elasticity increased slightly in the first 225 freeze-thaw cycles, then decreased in the following 75 cycles; the corresponding strain to peak stress decreased with the increase of freeze-thaw cycles. After 200 cycles, the rate of deterioration of concrete accelerated obviously.

Properties of High Strength Concrete with Calcined Diatomaceous Earth as Cement Replacement under Compression

2020 ◽  
Vol 402 ◽  
pp. 7-13
Author(s):  
Muttaqin Hasan ◽  
Aris Muyasir ◽  
Taufiq Saidi ◽  
Husaini ◽  
Raudha Azzahra
Keyword(s):  
Compressive Strength ◽  
Modulus Of Elasticity ◽  
High Strength Concrete ◽  
Diatomaceous Earth ◽  
High Strength ◽  
Compression Load ◽  
Strength Concrete ◽  
Cement Replacement ◽  
Concrete Mixtures ◽  
Compressive Strength Of Concrete

In this research, calcined diatomaceous earth from Aceh Besar, Indonesia was used as cement replacement in producing high strength concrete. Four concrete mixtures in which the percentage of cement replacement of 0%, 5%, 10% and 15% by weight were studied. Four cylinder-specimens with 100 mm diameter and 200 mm high were prepared for each mixture. The compression load was applied on the specimens at the age of 28 days until the specimens failed. The mixture without calcined diatomaceous earth was more workable than that with diatomaceous earth. The compressive strength of concrete with diatomaceous earth in this study was almost the same for all mixture. However, those compressive strength was lower than the compressive strength of concrete without calcined diatomaceous earth for about 14.6%. Modulus of elasticity of high strength concrete decreased with increasing of cement replacement percentage.

Effect of amorphous metallic fiber on mechanical properties of high-strength concrete exposed to high-temperature

2019 ◽  
Vol 218 ◽  
pp. 448-456 ◽  
Author(s):  
Gyeongcheol Choe ◽  
Gyuyong Kim ◽  
Hongseop Kim ◽  
Euichul Hwang ◽  
Sangkyu Lee ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
High Strength Concrete ◽  
High Strength ◽  
Strength Concrete ◽  
Metallic Fiber

Influences of Glassified Micro-Bubble on Mechanical Properties of Ultra-High-Strength Concrete after Exposure to High Temperature

2014 ◽  
Vol 629-630 ◽  
pp. 259-264
Author(s):  
Gai Fei Peng ◽  
Xiao Li Wang ◽  
Lin Wang
Keyword(s):  
Mechanical Properties ◽  
Experimental Investigation ◽  
High Temperature ◽  
High Strength Concrete ◽  
Room Temperature ◽  
High Strength ◽  
Strength Concrete ◽  
Micro Bubble ◽  
Residual Mechanical Properties ◽  
Tensile Splitting Strength

An experimental investigation was conducted to study residual mechanical properties of Ultra-High-Strength concrete with different dosages of glassified micro-bubble after exposure to high temperature. After exposure to different target temperatures (room temperature, 200 °C, 400 °C, 600 °C,800 °C), residual mechanical properties (residual compressive strength, residual tensile splitting strength, residual fracture energy) of Ultra-High-Strength concrete under different conditions including 1 water-binder ratios (0.18), 3 different contents of glassified micro-bubble (0%, 40%, 60%) were all investigated. The effect of different dosage of glassified micro-bubble was studied on residual mechanical properties of Ultra-High-Strength concrete after exposure to high temperature. The results indicate that the variations of different kinds of Ultra-High-Strength concrete with different dosage of glassified micro-bubble are basically the same. With the increase of temperature, the residual mechanical properties increase at first, then decrease. The residual mechanical properties decrease after exposure to high temperature of 800 °C.

The The Characterization and Modeling the Mechanical Properties of High Strength Concrete (HSC) Modified with Fly Ash (FA)

2020 ◽  
Vol 38 (2A) ◽  
pp. 173-184 ◽  
Author(s):  
Saman M. Kamal ◽  
Jalal A. Saeed ◽  
Ahmed Mohammed
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Curing Time ◽  
Strength Concrete ◽  
Statistical Variation ◽  
Study Results ◽  
Concrete Testing ◽  
Linked Model

One of the main challenges facing Civil Engineering community is to modify cement quantity in the mix design by admixtures to enhance the mechanical properties. According to more than 1000 data from literature, mechanical characteristics of concrete modified with FA were discussed. The statistical variation with modeling were achieved by set of data. The cement was replaced up to 70% with FA (weight of dry cement) and by cube of concrete testing up to 90 days of curing time and different w/c ratio. The compressive strength of concrete varied from 18-67 MPa, while, for modified concrete with FA, compressive strength ranged from 21-94 MPa, tensile strength ranged from 1-9 MPa and flexural strengths ranged from 3 - 10 MPa. The w/c ratio of concrete modified with FA varied from 0.24-0.53, also the FA content varied from 0-50 %. Vipulanandan correlation model was effective by connecting mechanical properties and compare with Hoek-Brown model. The nonlinear model was used to investigate the effect of FA on properties of normal and high strength concrete. Study results presented a worthy correlation between compressive strength and curing time, w/c ratio and FA content. By using the interactive linked (model) for compressive, tensile, and flexural strengths of concrete quantified well as a function of w/c ratio, curing time and FA content by using a nonlinear relationship.

Effect of different fiber types on the mechanical properties of normal and high strength concrete at elevated temperatures

2021 ◽  
Vol 12 (1) ◽  
pp. 30
Author(s):  
Mohamed Amin ◽  
Khaled Abu el-hassan
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
High Strength Concrete ◽  
Elevated Temperatures ◽  
Polypropylene Fiber ◽  
High Strength ◽  
Fiber Types ◽  
Strength Concrete ◽  
Compressive And Flexural Strengths ◽  
Fiber Addition

The effects of the types of fibers on mechanical properties of normal and high strength concrete under high temperature, up to 700 °C, was investigated. Three different- type fiber; "Steel Fiber (SF), Glass Fiber (GF) and Polypropylene Fiber (PPF)" are added into the concretes in five different ratios (0, 0.50, 1.00, 1.50 and 2.0%)of the volume under the following temperatures; 22, 100, 400 and 700°C. The results indicate that all the different types of fibers researched contribute to both the compressive and flexural strengths of concrete under high temperature, however, it is also found that this contribution decreases with an increase in temperature. The flexural strengths and compressive strengths for NSC and HSC mixes at 28 days under high temperature decreases as the temperature increases especially up to 400°C. Also, the best compressive and flexural strengths performance under high temperature was also those of SF. The compressive strength of the concrete incorporating SF was reduced under high temperature only, while the mixes containing PPF and GF were reduced under high temperature or with fiber addition. The optimum fiber addition ratios of the mixes containing PPF and GF are between 0.5-1.0 percent by volume. And for SF, it is 1.5% by the volume.

Effect of Aggregate on Mechanical Properties of Ultra-High Strength Concrete Exposed to High Temperature

2011 ◽  
Vol 23 (4) ◽  
pp. 431-440 ◽  
Author(s):  
Young-Sun Kim ◽  
Hyoung-Gil Choi ◽  
Yoshifumi Ohmiya ◽  
Gyu-Yong Kim
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
High Strength Concrete ◽  
High Strength ◽  
Strength Concrete
Sign in / Sign up

Export Citation Format

Share Document