scholarly journals Effect of the Amount of Water in the Synthesis of B-TiO2: Orange II Photodegradation

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
M. May-Lozano ◽  
G. M. Ramos-Reyes ◽  
R. López-Medina ◽  
S. A. Martínez-Delgadillo ◽  
J. Flores-Moreno ◽  
...  
Keyword(s):  
Surface Area ◽  
Sol Gel ◽  
Rutile Phase ◽  
Band Gap Energy ◽  
Molar Ratio ◽  
Orange Ii ◽  
X Ray Diffraction ◽  
X Ray ◽  
Boron Doped ◽  
Excess Water

A series of boron-doped TiO2 photocatalysts (2% B-TiO2) with different water/alkoxide molar ratio were synthesized by conventional sol-gel method. The prepared samples were characterized by BET measurement, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIRS), and diffuse-reflectance UV-vis. The phase anatase was present, but unexpectedly a small amount of rutile phase was formed with low and excess water in the synthesis. Additionally it has been observed that the increase in the molar ratio of water significantly increases the values of band gap energy and the specific surface area. Results showed that degradation of Orange II azo dye increases with surface area, particle size, boron, and water content in photocatalysis. The boron species were introduced in the tricoordinated form.

scholarly journals ZnFe2O4-TiO2Nanoparticles within Mesoporous MCM-41

2012 ◽  
Vol 2012 ◽  
pp. 1-8 ◽  
Author(s):  
Aidong Tang ◽  
Yuehua Deng ◽  
Jiao Jin ◽  
Huaming Yang
Keyword(s):  
Sol Gel ◽  
Rutile Phase ◽  
Band Gap Energy ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Agglomeration Of Nanoparticles ◽  
Adsorption Desorption ◽  
Mcm 41

A novel nanocomposite ZnFe2O4-TiO2/MCM-41 (ZTM) was synthesized by a sol-gel method and characterized through X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), N2adsorption-desorption, Raman spectroscopy, and ultraviolet visible (UV-vis) spectrophotometry. The results confirmed the incorporation of ZnFe2O4-TiO2nanoparticles inside the pores of the mesoporous MCM-41 host without destroying its integrity. ZnFe2O4nanoparticles can inhibit the transformation of anatase into rutile phase of TiO2. Incorporation of ZnFe2O4-TiO2within MCM-41 avoided the agglomeration of nanoparticles and reduced the band gap energy of TiO2to enhance its visible light photocatalytic activity. UV-vis absorption edges of ZTM nanocomposites redshifted with the increase of Zn/Ti molar ratio. The nanocomposite approach could be a potential choice for enhancing the photoactivity of TiO2, indicating an interesting application in the photodegradation and photoelectric fields.

Visible-Light-Induced Photocatalytic Activity of Boron-Doped BiVO4

2014 ◽  
Vol 809-810 ◽  
pp. 890-894
Author(s):  
Dan Li ◽  
Lian Wei Shan ◽  
Gui Lin Wang ◽  
Li Min Dong ◽  
Wei Li ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Diffuse Reflectance ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Reflectance Spectroscopy ◽  
Scheelite Structure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Boron Doped

Boron-BiVO4 samples were synthesized by sol-gel method. They were characterized by UV-vis diffuse reflectance spectroscopy, X-ray diffraction. Photocatalytic activity of the obtained BiVO4 samples was investigated through degrading methylene blue (MB). The results reveal that boron-BiVO4 catalysts have monoclinic scheelite structure. The BiVO4 and Co-BiVO4 photocatalysts were responsive to visible light. Co-BiVO4 photocatalyst showed higher photocatalytic activity than pure BiVO4, resulting in the significantly improved efficiency of degradation of MB.

scholarly journals Tuning Anatase-Rutile Phase Transition Temperature: TiO2/SiO2 Nanoparticles Applied in Dye-Sensitized Solar Cells

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Billy N. Cardoso ◽  
Emerson C. Kohlrausch ◽  
Marina T. Laranjo ◽  
Edilson V. Benvenutti ◽  
Naira M. Balzaretti ◽  
...  
Keyword(s):  
Phase Transition ◽  
Transition Temperature ◽  
Surface Area ◽  
Phase Transition Temperature ◽  
Dye Sensitized Solar Cells ◽  
Rutile Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Molar Percent

TiO2/SiO2 nanoparticles with 3, 5, and 10 molar percent of silica, were synthesized by hydrothermal method and characterized by SEM, TEM, N2 adsorption-desorption isotherms, X-ray diffraction, and Raman and UV-Vis spectroscopy. While pristine TiO2 thermally treated at 500°C presents a surface area of 36 m2 g-1 (±10 m2 g-1), TiO2/SiO2 containing 3, 5, and 10 molar percent of silica present surface areas of 93, 124, and 150 m2 g-1 (±10 m2 g-1), respectively. SiO2 is found to form very small amorphous domains well dispersed in the TiO2 matrix. X-ray diffraction and Raman spectroscopy data show that anatase-to-rutile phase transition temperature is delayed by the presence of SiO2, enabling single-anatase phase photoanodes for DSSCs. According to the I×V measurements, photoanodes with 3% of SiO2 result in improved efficiency, which is mainly related to increased surface area and dye loading. In addition, the results suggest a gain in photocurrent related to the passivation of defects by SiO2.

Bicontinuous nanodisc and nanospherical titania materials prepared by sol-gel process in reverse microemulsion

2012 ◽  
Vol 66 (3) ◽  
Author(s):  
Khaled Haouemi ◽  
Fathi Touati ◽  
Néji Gharbi
Keyword(s):  
Sol Gel ◽  
Textural Properties ◽  
Rutile Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Tio2 Particles ◽  
Sol Gel Process ◽  
Bet Method ◽  
Reverse Microemulsions ◽  
Different Shapes

AbstractTiO2 nanoparticles with different shapes and sizes were synthesised by the sol-gel route in Water/Brij78/Hexane reverse microemulsions. The aqueous cores of these microemulsions were used as nanoreactors to control sol-gel reactions. We studied the effect of water/surfactant mole ratio (W 0) on the morphology, and textural properties of the final products. The materials thus obtained were characterised by different techniques. Thermogravimetric and differential thermal analysis (TG-DTA) was used to study the thermal behaviour of the products and X-ray diffraction (XRD) to identify the crystalline phases. The morphological and textural properties of the products were determined by scattering electron microscopy (SEM) and the Brunauer-Emmett-Teller (BET) method, respectively. We also studied the influence of thermal treatment on the structure and size of the TiO2 particles. The effect of W 0 on the anatase-rutile phase transition temperature was investigated.

Study of Heating Effect on Specific Surface Area, and Changing Optical Properties of ZnO Nanocrystals

2011 ◽  
Vol 403-408 ◽  
pp. 1205-1210
Author(s):  
Jaleh Babak ◽  
Ashrafi Ghazaleh ◽  
Gholami Nasim ◽  
Azizian Saeid ◽  
Golbedaghi Reza ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Energy Gap ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Zno Nanocrystals ◽  
Transmission Electron ◽  
Zno Nanocrystal

In this work ZnO nanocrystal powders have been synthesized by using Zinc acetate dehydrate as a precursor and sol-gel method. Then the products have been annealed at temperature of 200-1050°C, for 2 hours. The powders were characterized using X-ray diffraction (XRD), UV-vis absorption and photoluminescence (PL) spectroscopy. The morphology of refrence ZnO nanoparticles have been studied using Transmission Electron Microscope (TEM). During the annealing process, increase in nanocrystal size, defects and energy gap quantitative, and decrease in specific surface area have been observed.

Preparation of Nanosized TiO2 Synthesized by Sol-Gel Pathway Using Ionic Liquid as Assistant and its Photocatalytic Activities

2012 ◽  
Vol 535-537 ◽  
pp. 2240-2244
Author(s):  
Wei Wei ◽  
Chang Shun Yu ◽  
Shao Jun Wang ◽  
Qing Da An
Keyword(s):  
Ionic Liquid ◽  
Diffuse Reflectance ◽  
Sol Gel ◽  
Rutile Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Photocatalytic Activities ◽  
Average Size ◽  
Nanosized Tio2

Nanosized TiO2 particles were synthesized by sol-gel method using ionic liquid as assistant. The samples were characterized by UV-vis diffuse reflectance spectra, X-ray diffraction (XRD), transmission electron microscopy (TEM). It was shown that the phase detectable was mainly rutile phase with uniform sphericity and the average size was 10nm. Along with the rise of sintering temperature, grain diameter became bigger. The photocatalytic activities of nanosized TiO2 were evaluated by the reduction yield in the presence of CO2 and water. The result showed that TiO2 catalysts has efficient photocatalytic activities, of which made with [OMIM]BF4 displayed the highest photocatalytic active in the experiment.

The Effect of Stabiliser’s Molarity to the Growth of ZnO Nanorods

2011 ◽  
Vol 312-315 ◽  
pp. 99-103 ◽  
Author(s):  
Zuraida Khusaimi ◽  
Mohamad Hafiz Mamat ◽  
Mohd Zainizan Sahdan ◽  
Norbani Abdullah ◽  
Mohamad Rusop
Keyword(s):  
Sol Gel ◽  
Zno Nanorods ◽  
Structural Features ◽  
Zinc Nitrate ◽  
Molar Ratio ◽  
Nitrate Hexahydrate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wet Chemical ◽  
Gel Preparation

A wet chemical approach, originating from sol-gel preparation, was adopted with the intention to develop a low-temperature benign method of preparation. ZnO nanorods are successfully grown in an aqueous medium. The precursor, zinc nitrate hexahydrate (Zn(NO3)2.6H2O), is stabilized by hexamethylene tetraamine (HMTA). The effect of changing the molarity of HMTA to the structural orientation of ZnO nanorods is investigated. X-ray diffraction of the synthesized ZnO shows hexagonal zincite structure. The structural features of the nanocrystalline ZnO were studied by SEM. Structural features, surface morphology and differences in lattice orientation are seemingly influenced by varying the Zn2+: HMTA molar ratio. The formation of ZnO nanorods with blunt and sharp tips is found to be significantly affected by this ratio.

Synthesis, Characterization and Photocatalytic Activity of Nb-Doped TiO2 Nanoparticles

2012 ◽  
Vol 455-456 ◽  
pp. 110-114 ◽  
Author(s):  
Xuan Dong Li ◽  
Xi Jiang Han ◽  
Wen Ying Wang ◽  
Xiao Hong Liu ◽  
Yan Wang ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Photocatalytic Activity ◽  
Methyl Orange ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Doped Tio2 ◽  
X Ray ◽  
Vis Spectroscopy

Nb-doped TiO2 powders with different concentrations of Nb have been synthesized by a sol-gel method and characterized by a series of technologies including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and UV-vis spectroscopy. The photocatalytic activity of Nb-doped TiO2 is evaluated by degradation efficiency of methyl orange in aqueous solution. The results indicate that the photocatalytic activity of Nb-doped TiO2 synthesized with a Nb/Ti molar ratio of 5% is higher than that of TiO2 under the visible light.

scholarly journals Synthesis and Characterisation of Mesoporous TiO2 Nanoparticles by Novel Surfactant Assisted Sol-gel Method for the Degradation of Organic Compounds

2018 ◽  
Vol 63 (1) ◽  
pp. 85-95 ◽  
Author(s):  
Harish Phattepur ◽  
Gowrishankar Bychapur Siddaiah ◽  
Nagaraju Ganganagappa
Keyword(s):  
Electron Microscopy ◽  
Tio2 Nanoparticles ◽  
Surface Area ◽  
Sol Gel ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
Tio2 Nps ◽  
Gel Method ◽  
X Ray ◽  
Surfactant Assisted

A sol-gel method was employed to synthesise pure titanium dioxide (TiO2) and surfactant assisted TiO2 nanoparticles (NPs). The effect of novel surfactant viz., Lauryl lactyl lactate on photocatalytic properties of TiO2 was studied. TiO2 NPs were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), UV-Vis Diffuse Reflectance spectra (DRS), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), Thermo gravimetric analysis (TGA), and Brunauer – Emmet - Teller (BET) surface area. Anatase phase of TiO2 was confirmed by X-Ray diffraction pattern and the crystallite size was between 9–19 nm. Addition of surfactant improved the BET surface area, surface defects, while the agglomeration of particles was reduced. DRS results revealed that the addition of surfactant to TiO2 sol induced a red shift of the absorption edge which resulted in the reduction of band gap from 3.23 to 3.21 eV. These physicochemical properties of TiO2 NPs were correlated with photocatalytic degradation of phenol. About 92% of phenol degradation was observed for surfactant assisted TiO2 NPs (SA-TiO2). Salicylic acid and caffeine were also degraded using SA-TiO2 NPs.

Morphology and Phase Composition of Sol-Gel Derived Aluminum Borate Nanowhiskers

2015 ◽  
Vol 659 ◽  
pp. 121-126 ◽  
Author(s):  
Pat Sooksaen
Keyword(s):  
Fourier Transform ◽  
Phase Composition ◽  
Sol Gel ◽  
Molar Ratio ◽  
Aluminum Borate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Higher Temperature ◽  
Sol Gel Synthesis ◽  
Scanning Electron

Aluminium borate nanowhiskers with varying aspect ratio were synthesized via sol–gel synthesis. The morphology of aluminum borate (Al4B2O9 and Al18B4O33) nanowhiskers could be controlled by varying the aluminum to boron (Al:B) molar ratio in the sol–gel derived precursors. Sintering temperatures (850 and 1100°C) and sintering times (4 and 32 hours) also affected the phase composition and size of the nanowhiskers. Citric acid was also added in the sol–gel derived precursors as a surface stabilizer for obtaining uniform finely dispersed nanostructures. Fine nanowhiskers were obtained by the calcination at 850°C, whereas higher temperature of 1100°C led to thicker and longer nanowhiskers and became rod-like crystals. The morphology and phase composition were investigated by field emission scanning electron microscope and X-ray diffraction. Chemical bond vibrations in the synthesized nanowhiskers were investigated by Fourier-transform infrared spectroscopy.

Sign in / Sign up

Export Citation Format

Share Document