scholarly journals Effect of Aging Treatment on the Damping Capacity and Mechanical Properties of Mg-6Al-1Zn Alloy

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Abdel-Wahab El-Morsy ◽  
Ahmed I. Z. Farahat
Keyword(s):  
Mechanical Properties ◽  
Aging Time ◽  
Damping Ratio ◽  
Aging Treatment ◽  
Peak Level ◽  
Free Vibrations ◽  
Logarithmic Decrement ◽  
Damping Capacity ◽  
Damping Characteristics ◽  
Heat Treated

The damping capacity and mechanical properties of Mg-6Al-1Zn alloy after heat treatment were investigated. The damping characteristics of un-heat-treated, solution treated, and aged Mg-6Al-1Zn specimens were determined by measuring the damping ratio and the logarithmic decrement of free vibrations of a bending beam clamped at one side. The microstructural evaluations confirmed that theβ-Mg17Al12phase was reprecipitated after aging and increased with an increase in aging time. The peak level of damping ratio and logarithmic decrement was obtained after 34 hr of aging time, over which the damping capacity declined according to increasing amount of strong pining points.

Mechanical Behavior of Friction Stir Welded AA-6061 Thick Plates in Different Heat Treatment Conditions

2021 ◽  
Vol 875 ◽  
pp. 203-210
Author(s):  
Talha Ahmed ◽  
Wali Muhammad ◽  
Zaheer Mushtaq ◽  
Mustasim Billah Bhatty ◽  
Hamid Zaigham
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aging Treatment ◽  
Travel Speed ◽  
Butt Joint ◽  
Tensile Fracture ◽  
Friction Stir ◽  
Treatment Conditions ◽  
Heat Treated ◽  
Joint Form

In this study, mechanical properties of friction stir welded Aluminum Alloy (AA) 6061 in three different heat treatment conditions i.e. Annealed (O), Artificially aged (T6) and Post Weld Heat Treated (PWHT) were compared. Plates were welded in a butt joint form. Parameters were optimized and joints were fabricated using tool rotational speed and travel speed of 500 rpm and 350 mm/min respectively. Two sets of plates were welded in O condition and out of which one was, later, subjected to post weld artificial aging treatment. Third set was welded in T6 condition. The welds were characterized by macro and microstructure analysis, microhardness measurement and mechanical testing. SEM fractography of the tensile fracture surfaces was also performed. Comparatively better mechanical properties were achieved in the plate with PWHT condition.

Effect of Artificial Aging on Microstructures and Mechanical Properties of Extruded Mg Alloy ZK60

2014 ◽  
Vol 697 ◽  
pp. 72-75
Author(s):  
De Liang Yin ◽  
Jian Qiao ◽  
Hong Liang Cui
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
Aging Time ◽  
Artificial Aging ◽  
Aging Treatment ◽  
Tensile Tests ◽  
Tensile Yield Strength ◽  
Uniaxial Tensile ◽  
Fracture Elongation ◽  
Strength And Ductility

An extruded ZK60 magnesium alloy was subjected to artificial aging at 180 oC for an investigation of the effect of aging time on its precipitation behavior and mechanical properties. Uniaxial tensile tests were conducted to obtain the mechanical properties. Optical microscopy and transmission electron microscopy (TEM) were employed to observe microstructure change before and after aging treatment. It is shown that, both tensile yield strength and ultimate tensile strength increases with aging time. The fracture elongation after aging for 20 h reaches up to 21.0%, and the yield strength increases to 269.5 MPa, 19.4% higher than that of extruded specimens (un-aged), showing a good match of strength and ductility. Three newly-formed precipitates were observed after aging for over 20 h, among which particulate and dispersive precipitates should be responsible for the good combination of strength and ductility.

The Effect of Heat Treatment on Fatigue and Mechanical Properties of 6061 Aluminium Alloy

2014 ◽  
Vol 699 ◽  
pp. 227-232
Author(s):  
Nurulhilmi Zaiedah Nasir ◽  
Mohd Ahadlin Mohd Daud ◽  
Mohd Zulkefli Selamat ◽  
Ahmad Rivai ◽  
Sivakumar Dhar Malingam
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Impact Strength ◽  
Aluminium Alloy ◽  
Aging Treatment ◽  
Hardness Measurement ◽  
Hardness Tester ◽  
Quenching Media ◽  
Heat Treated ◽  
6061 Aluminium Alloy

This paper investigated the effect of heat treatment on mechanical properties and microstructure of 6061 aluminium alloy. The aluminium alloys were examined in the heat treated conditions, using different quenching media, water and oil. The alloy was solution heat treated at temperature of 529oC for one, three and five hour respectively. Aging treatment was carried out at temperature of 160oC which is assumed to be the best temperature for ageing process. Hardness measurement was carried out using a Brinell Hardness Tester Machine. The results shows hardness and impact strength are inversely proportional to each other, as the hardness of 6061 aluminium alloy decreases and impact strength increases.

scholarly journals Study on the Aging Time Variation Law of Mechanical Properties of the Laminated Rubber Bearing in Coastal Bridges considering Frictional Slip

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Yue Li ◽  
Chongming Gao ◽  
Chong Li ◽  
Qian Li
Keyword(s):  
Mechanical Properties ◽  
Aging Time ◽  
Damping Ratio ◽  
Viscous Damping ◽  
Equivalent Viscous Damping ◽  
Coastal Bridges ◽  
Shape Coefficient ◽  
Rubber Bearings ◽  
Frictional Slip ◽  
Equivalent Viscous Damping Ratio

As an important support member in the structural system of coastal bridges, the frictional slip and the rubber aging of laminated rubber bearings will affect the service safety of the overall structure in earthquakes. In order to investigate the mechanical properties aging law of the rubber bearings considering frictional slip in the coastal bridges, a frictional slip experiment was carried out on the laminated rubber bearings. Moreover, the influence of rubber aging on the mechanical properties of the bearings with various shape coefficients was analyzed by the finite element method during the 100 years of service life of bridges. The results indicate that (1) the horizontal and vertical stiffness of the bearing increase linearly with the aging time of the rubber. The amplification of the bearing stiffness also grows with the shape coefficient of the bearing. (2) The frictional slip initiation displacement of the bearing grows with the rubber aging time. Furthermore, the larger the shape coefficient of the bearing is, the more the frictional slip initiation displacement of the bearing increases. (3) With the increase of the aging time, the equivalent viscous damping ratio of the bearing continues to increase and more energy is consumed by frictional slip. For the bearing with the shape coefficient of 16.38, the equivalent viscous damping ratio at 100 years of rubber aging time is 1.17 times higher than that of the initial state of the bearing, and 33.21% more energy is consumed through frictional slip. Given that the marine environment accelerates rubber aging and changes the mechanical properties, the effects of the frictional slip and rubber aging properties of the laminated rubber bearings on the seismic dynamic response of bridges should be considered in the seismic design of coastal bridges.

Enhancement of Mechanical Properties of Cast Beta-Type Titanium Alloy by Aging Treatment

2018 ◽  
Vol 929 ◽  
pp. 42-49
Author(s):  
Zuldesmi Mansjur ◽  
Hendro Maxwel Sumual
Keyword(s):  
Mechanical Properties ◽  
Aging Time ◽  
Vickers Hardness ◽  
Aging Temperature ◽  
Dendritic Structure ◽  
Solution Treatment ◽  
Aging Treatment ◽  
High Oxygen Content ◽  
Precision Casting ◽  
Β Phase

Beta type Ti-29Nb-13Ta-4.6Zr alloy (TNTZ) is one of the titanium alloys which have gained much attention in dental applications. Dental precision casting is predominant for fabricating dental prostheses. However, there is a possibility for the mechanical properties of its casting to be degraded because of a α case, shrinkages and pores and a dendrite structure. One of the ways to enhance their mechanical properties is heat treatment process. Therefore, the aim of this study is to investigate the effect of aging treatment on mechanical properties and microstructure of TNTZ cast into magnesia based mold in order to improve its mechanical properties. As results, the Vickers hardness of the cast TNTZ after solution treatment is larger than that of the wrought TNTZ. The aging curve of the cast and the wrought TNTZ at an aging temperature of 673 K and 723 K exhibit almost similar pattern. For each aging time, the higher the aging temperature, the smaller the Vickers hardness for both alloys. Microstructures of cast TNTZ at various aging conditions consist of a dendritic structure and the average diameters of their grain size are around 40 μm. The diffraction peaks of precipitation of α and β phase s are detected in under aging (UA), peak aging (PA) and over aging (OA) conditions for both aging temperatures. However, the diffraction peak of ω phase is observed only in OA condition for cast TNTZ at aging temperature of 673 K. The highest tensile strength of the cast TNTZ and the wrought TNTZ at both aging temperatures are in PA condition and the elongation decrease continuously by increasing aging time. The tensile strengths of cast TNTZ in UA, PA and OA conditions at an aging temperature of 723 K are lower and their elongations are higher in comparison with those of 673 K. The high oxygen content seems to contribute to the poor elongation. SEM fractographs of the cast TNTZ at aging temperatures of 673 and 723 K in UA, PA and OA conditions show the brittle morphology with intergranular fracture that increases with increasing of aging time.

The Effects of Two-Stage Aging on the Microstructure and Mechanical Properties of the New Al-Si-Cu-Mg Alloy

2016 ◽  
Vol 850 ◽  
pp. 581-586 ◽  
Author(s):  
Yan Zheng ◽  
Cong Xu ◽  
Wen Long Xiao ◽  
Hiroshi Yamagata ◽  
Guo Fu Ji ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aging Time ◽  
Aging Treatment ◽  
Experimental Results ◽  
Mg Alloy ◽  
Casting Alloy ◽  
Two Stage ◽  
Microstructure And Mechanical Properties

Two-stage aging treatments were applied to Al-6Si-2Cu-0.5Mg casting alloy, and the influence of aging treatment parameters on the microstructure and mechanical properties was investigated. The experimental results indicated that the microstructure and mechanical properties of Al-6Si-2Cu-0.5Mg alloy were significantly influenced by the aging time and temperature, and the elongation remarkably increased with the aging time increasing before 7 h. In the case of the alloy aged at 200°Cfor 2h, higher hardness and tensile strength were obtained, which may be attributed to precipitation of a large amount of Cu-rich phases. However, the higher elongation was achieved in the alloy under 200°C aging treatment for 5h, while its hardness and tensile strength slightly decreased. It is mainly due to the amount of the Cu-rich phases decrease slightly, but the morphology of the phases evolved from plate-like to bulk-like structure.

The Effect of Aging Heat Treatment on the Mechanical Properties of Cu-Al-Fe-(x) Alloys

2011 ◽  
Vol 467-469 ◽  
pp. 257-262
Author(s):  
Guo Fa Mi ◽  
Jin Zhi Zhang ◽  
Hai Yan Wang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Aging Time ◽  
Solution Treatment ◽  
Aging Treatment ◽  
Experimental Result ◽  
Electric Resistance ◽  
Suitable Heat Treatment ◽  
Ni Alloy

Alloys were produced by casting of Cu-Al-Fe-Be and Cu-Al-Fe-Ni aluminum bronzes and aged. The microstructures and mechanical properties were evaluated. The results indicated that solution and aging treatment can significantly improve the plasticity of Cu-Al-Fe-Be and Cu-Al-Fe-Ni, while the strength and hardness remained in the quenched level. Extending the aging time can effectively enhance the mechanical properties of alloys, and the longer the aging time, the higher the electric resistance of alloys. According to the results, the mechanical properties of the Cu-Al-Fe-Be alloy can be improved remarkably by solution treatment for 120 min at 950°C, followed by aging treatment for 120 min at 350°C, and quenched. While the most suitable heat treatment for the Cu-Al-Fe-Ni alloy was solution treatment 120 min at 950°C, followed by aging for 120 min at 450°C, and quenched. The experimental result also suggested that the Cu-Al-Fe-Be alloy possessed higher hardness and tensile strength compared to the Cu-Al-Fe-Ni alloy.

Effects of Isothermal Aging on Microstructure Evolution of Biomedical Co-Cr-Mo Alloy

2015 ◽  
Vol 658 ◽  
pp. 31-35 ◽  
Author(s):  
Pitak Khaimanee ◽  
Paiboon Choungthong ◽  
Vitoon Uthaisangsuk
Keyword(s):  
Aging Time ◽  
Isothermal Aging ◽  
Aging Treatment ◽  
Hardness Test ◽  
Orthopedic Implants ◽  
Phase Fraction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Microstructure Examination

Cobalt based alloys have been widely used in orthopedic implants. These alloys are an allotropic metal, which commonly exhibits two crystal structures, namely, FCC and HCP lattice. In this work, developed microstructure and hardness of a Co-Cr-Mo alloy after isothermal aging treatment were investigated. The applied aging procedure included soaking at the temperature of 850°C for five different holding times of 1, 3, 6, 9 and 12 h with subsequent water quenching. Microstructure examination, X-ray diffraction analysis and micro-hardness test were carried out for both as-received and heat-treated cobalt based alloys. The results showed that the FCC to HCP phase transformation occurred during the isothermal aging. It was observed that phase fraction of the identified HCP phase increased with longer aging time. Microstructure of the samples aged for 12 h showed very fine lamellae morphologies similar to a pearlitic structure with different orientations within each FCC grain. Apparently, these occurred lamellae structures could be well correlated with the formation of the HCP martensite. Additionally, it was found that in the Co-Cr-Mo alloy sigma phase precipitated early at the grain boundaries and further grew along these boundaries by increasing aging time. The hardness value of the examined alloy slightly increased with larger HCP phase fraction. The increased aging time certainly led to higher amount of the HCP martensite and consequently increased hardness and possible wear resistance properties.

Microstructure, mechanical properties and damping capacity of heat-treated Mg–Zn–Y–Nd–Zr alloy

2014 ◽  
Vol 609 ◽  
pp. 283-292 ◽  
Author(s):  
Suqin Feng ◽  
Wenying Zhang ◽  
Yanhui Zhang ◽  
Jinyu Guan ◽  
Yongchun Xu
Keyword(s):  
Mechanical Properties ◽  
Damping Capacity ◽  
Heat Treated ◽  
Zr Alloy

The Effect of the Severe Plastic Deformation on the Artificial Aging of the AlMgSi1 Alloy

2015 ◽  
Vol 812 ◽  
pp. 239-245
Author(s):  
Judit Pázmán ◽  
Péter Bereczki ◽  
Balázs Verő ◽  
Ibolya Kardos ◽  
Jánosné Fehér
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Automotive Industry ◽  
Artificial Aging ◽  
Profile Analysis ◽  
Aging Treatment ◽  
X Ray ◽  
Heat Treated ◽  
Deformation And Heat Treatment

The AlMgSi1 alloy is generally used in automotive industry owing to its excellent mechanical properties, which can be further improved by applying severe plastic deformation and heat treatment. The dislocation density in the material increases significantly during severe plastic deformation due to the characteristic intensive shear strain. Therefore the motion of dislocations becomes more and more retarded, consequently the strength improves. In addition, the motion of dislocations can be prevented by aging due to formation of coherent precipitations in the metal matrix in order to realize further increasing in strength. In this paper the combined effect of severe plastic deformation and artificial aging treatment on the evolution of mechanical properties was investigated. The samples were subjected to multiple forging (MF) process at room and enhanced temperature. One part of the deformed samples were heat treated at 150°C for different times. The deformed as well as deformed and heat treated samples were investigated by micro hardness testing and X-ray profile analysis.

Sign in / Sign up

Export Citation Format

Share Document