scholarly journals A Precipitation Phenomenon of Titanium Compounds in Aluminum Melts and the Refinement Fading Mechanism of the Al-5Ti-0.62C Master Alloy

2015 ◽  
Vol 2015 ◽  
pp. 1-9
Author(s):  
Wanwu Ding ◽  
Wenjun Zhao ◽  
Tiandong Xia
Keyword(s):  
Electron Microscopy ◽  
Master Alloy ◽  
Molten Aluminum ◽  
Pure Aluminum ◽  
X Ray Diffraction ◽  
X Ray ◽  
Commercially Pure ◽  
Titanium Compounds ◽  
Refinement Effect ◽  
Scanning Electron

The Al-5Ti-0.62C master alloy was prepared through a method of thermal explosion in molten aluminum. The process of remelting and refining of commercially pure aluminum was conducted, and precipitation samples with different heat-treatment times were obtained. Scanning electron microscopy (SEM), X-ray diffraction (XRD), optical microscopy (OM), and other techniques were used to analyze the microstructure of the precipitates at the bottom of the samples so as to explore the fading mechanism of Al-Ti-C alloy refinement. The results showed that an obvious precipitation phenomenon of titanium compounds existed in the remelted Al-5Ti-0.62C master alloy and that there were both TiC compounds and TiAl3compounds in the precipitates; in the refined pure aluminum samples, the precipitates were mainly TiC compounds. Precipitation of titanium compounds in aluminum melting is the main cause of fading in the refinement effect of an Al-Ti-C master alloy.

Investigation on the Preparation Processes of Cu-Bi Master Alloy

2011 ◽  
Vol 335-336 ◽  
pp. 841-844 ◽  
Author(s):  
Li Na Zhang ◽  
Bai Xiong Liu
Keyword(s):  
Electron Microscopy ◽  
Melting Temperature ◽  
Master Alloy ◽  
Holding Time ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Two Phases ◽  
Fluorescence Analyzer ◽  
Scanning Electron

The Microstructure of Cu-Bi master alloy with different melt processes, such as different melting temperature and holding time, was observed by PHILIPS-XL30 scanning electron microscopy (SEM); phase analysis was conducted by Miniflex X-ray diffraction(XRD); Magix(PW2424) X-ray fluorescence analyzer(XRF) was used to analyze chemical compositions of Cu-Bi master alloy. The results show that there are Cu and Bi two phases in the Cu-Bi master alloy; The yielding rate of bismuth decreases with the rising melting temperature. It decreases slowly between 1100 °C to 1150 °C,while it decreases rapidly between 1150 °C to 1200 °C.The bismuth particles in the Cu-Bi master alloy prepared at 1100 °C are much larger than those prepared at 1150 °C,while the size of bismuth particles change little from 1150 °C to 1200 °C. So the better melting temperature of preparing Cu-Bi master alloy is 1150 °C.The yielding rate of bismuth decreases with the holding time increasing. But when the holding time is too short, there are large bismuth particles in Cu-Bi alloy .So the better holding time is 120s.

Research on Grain Refinement Effect of Al-5Ti-C Alloy on Pure Aluminum and its Attenuation Mechanism

2013 ◽  
Vol 477-478 ◽  
pp. 1293-1297
Author(s):  
Wan Wu Ding ◽  
Tian Dong Xia ◽  
Jiang Tao Zhu ◽  
Wen Jun Zhao ◽  
Yang Tao Xu
Keyword(s):  
Grain Refinement ◽  
Pure Aluminum ◽  
Texture Feature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Commercially Pure ◽  
Titanium Compound ◽  
Attenuation Mechanism ◽  
Heat Preservation ◽  
Refinement Effect

The texture feature and grain refinement effect of Al-5Ti-C alloy on pure aluminum were analyzed and its attenuation mechanism was discussed by using X-ray diffraction (XRD), scanning electron microscopy (SEM), optical microscopy (OM) and other experimental methods.The results show that: Al-5Ti-C alloy is composed of Al, TiAl3 and TiC. Al-5Ti-C alloy has a good grain refining capacity for commercially pure aluminum. During the heat preservation process, due to precipitation of titanium compound in the aluminum melt, refinement effect of Al-Ti-C alloy is declined.

Identification of calcium oxalate crystals in dried or fixed tobacco leaf

1984 ◽  
Vol 42 ◽  
pp. 288-289
Author(s):  
Vicki L. Baliga ◽  
Mary Ellen Counts
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Calcium Oxalate ◽  
Growth And Development ◽  
Polarized Light ◽  
Calcium Oxalate Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Calcium is an important element in the growth and development of plants and one form of calcium is calcium oxalate. Calcium oxalate has been found in leaf seed, stem material plant tissue culture, fungi and lichen using one or more of the following methods—polarized light microscopy (PLM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and x-ray diffraction.Two methods are presented here for qualitatively estimating calcium oxalate in dried or fixed tobacco (Nicotiana) leaf from different stalk positions using PLM. SEM, coupled with energy dispersive x-ray spectrometry (EDS), and powder x-ray diffraction were used to verify that the crystals observed in the dried leaf with PLM were calcium oxalate.

Environmental scanning electron microscopy of fresh human gallstones reveals new morphologies of precipitated calcium salts

1992 ◽  
Vol 50 (2) ◽  
pp. 1322-1323
Author(s):  
Howard S. Kaufman ◽  
Keith D. Lillemoe ◽  
John T. Mastovich ◽  
Henry A. Pitt
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Environmental Scanning Electron Microscopy ◽  
Environmental Scanning ◽  
X Ray Diffraction ◽  
Calcium Salts ◽  
Cholesterol Gallstones ◽  
X Ray ◽  
Ca Carbonate ◽  
Scanning Electron

Gallstones contain precipitated cholesterol, calcium salts, and proteins. Calcium (Ca) bilirubinate, palmitate, phosphate, and carbonate occurring in gallstones have variable morphologies but characteristic windowless energy dispersive x-ray (EDX) spectra. Previous studies of gallstone microstructure and composition using scanning electron microscopy (SEM) with EDX have been limited to dehydrated samples. In this state, Ca bilirubinates appear as either glassy masses, which predominate in black pigment stones, or as clusters, which are found mostly in cholesterol gallstones. The three polymorphs of Ca carbonate, calcite, vaterite, and aragonite, have been identified in gallstones by x-ray diffraction, however; the morphologies of these crystals vary in the literature. The purpose of this experiment was to study fresh gallstones by environmental SEM (ESEM) to determine if dehydration affects gallstone Ca salt morphology.Gallstones and bile were obtained fresh at cholecystectomy from 6 patients. To prevent dehydration, stones were stored in bile at 37°C. All samples were studied within 4 days of procurement.

Photocatalytic activity of TiO2 synthesized by anodization and anodic spark deposition

MRS Advances ◽  
2020 ◽  
Vol 5 (61) ◽  
pp. 3141-3152
Author(s):  
Alma C. Chávez-Mejía ◽  
Génesis Villegas-Suárez ◽  
Paloma I. Zaragoza-Sánchez ◽  
Rafael Magaña-López ◽  
Julio C. Morales-Mejía ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Surface Characteristics ◽  
Amorphous Solids ◽  
X Ray Diffraction ◽  
X Ray ◽  
Catalytic Activities ◽  
Anodic Spark Oxidation ◽  
Porous Surfaces ◽  
Scanning Electron

AbstractSeveral photocatalysts, based on titanium dioxide, were synthesized by spark anodization techniques and anodic spark oxidation. Photocatalytic activity was determined by methylene blue oxidation and the catalytic activities of the catalysts were evaluated after 70 hours of reaction. Scanning Electron Microscopy and X Ray Diffraction analysis were used to characterize the catalysts. The photocatalyst prepared with a solution of sulfuric acid and 100 V presented the best performance in terms of oxidation of the dye (62%). The electric potential during the synthesis (10 V, low potential; 100 V, high potential) affected the surface characteristics: under low potential, catalyst presented smooth and homogeneous surfaces with spots (high TiO2 concentration) of amorphous solids; under low potential, catalyst presented porous surfaces with crystalline solids homogeneously distributed.

The Effect of the Microstructure of Diffusion Barriers on the Palladium Activation for Electroless Copper Deposition

2002 ◽  
Vol 716 ◽  
Author(s):  
Seok Woo Hong ◽  
Yong Sun Lee ◽  
Ki-Chul Park ◽  
Jong-Wan Park
Keyword(s):  
Electron Microscopy ◽  
Diffusion Barriers ◽  
Copper Deposition ◽  
X Ray Diffraction ◽  
Plan View ◽  
X Ray ◽  
Transmission Electron ◽  
Electroless Copper ◽  
Sheet Resistance Measurement ◽  
Scanning Electron

AbstractThe effect of microstructure of dc magnetron sputtered TiN and TaN diffusion barriers on the palladium activation for autocatalytic electroless copper deposition has been investigated by using X-ray diffraction, sheet resistance measurement, field emission scanning electron microscopy (FE-SEM) and plan view transmission electron microscopy (TEM). The density of palladium nuclei on TaN diffusion barrier increases as the grain size of TaN films decreases, which was caused by increasing nitrogen content in TaN films. Plan view TEM results of TiN and TaN diffusiton barriers showed that palladium nuclei formed mainly on the grain boundaries of the diffusion barriers.

PENINGKATAN LAJU DISOLUSI ACYCLOVIR DENGAN METODE SISTEM DISPERSI PADAT MENGGUNAKAN POLOXAMER 188

2016 ◽  
Vol 5 (1) ◽  
pp. 6
Author(s):  
Budi Setiawan ◽  
Erizal Zaini ◽  
Salman Umar
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Differential Thermal Analysis ◽  
Fourier Transform Infrared ◽  
X Ray Diffraction ◽  
Poloxamer 188 ◽  
X Ray ◽  
Scanning Electron

Sebuah penelitian tentang sistem dispersi padat dari asiklovir dengan poloxamer 188 telah dilakukan formulasi dengan pencampuran secara fisika dengan rasio 1 : 1, 1 : 3, 1 : 5 dan dispersi padat 1 : 1, 1 : 3, 1 : 5 dan penggilingan 1:1 sebagai pembanding. Dispersi padat dibuat menggunakan metode pencairan (fusi), yang digabung dengan poloxamer 188 pada hotplate kemudian asiklovir dimasukkan ke dalam hasil poloxamer 188 lalu di kocok hingga membentuk masa homogen. Semua formula yang terbentuk termasuk asiklovir poloxamer 188 murni dianalisis karakterisasinya dengan Differential Thermal Analysis (DTA), X-ray Diffraction, Scanning Electron Microscopy (SEM), dan Fourier Transform Infrared (FTIR), kemudian pengambilan dilakukan  (penentuan kadar) mengunakan spektrofotometer UV pada panjang gelombang 257,08 nm dan uji laju disolusi dengan aquadest bebas CO2 menggunakan metode dayung. Hasil pengambilan  (penentuan kadar) menunjukkan bahwa semua formula memenuhi persyaratan farmakope Amerika edisi 30 dan farmakope Indonesia edisi 4 yaitu 95-110%. Sedangkan hasil uji laju disolusi untuk campuran fisik 1: 1, dan dispersi padat 1: 1, dan penggilingan 1: 1 menunjukkan peningkatan yang nyata dibandingkan asiklovir murni. Hal ini juga dapat dilihat dari hasil perhitungan statistik  menggunakan analisis varian satu arah  SPSS 17.

Structural Characterization of Gallbladder Stones Using Energy Dispersive X-ray Spectroscopy and X-ray Diffraction

2018 ◽  
Vol 21 (7) ◽  
pp. 495-500 ◽  
Author(s):  
Hassan A. Almarshad ◽  
Sayed M. Badawy ◽  
Abdalkarem F. Alsharari
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Energy Dispersive ◽  
Spectroscopic Techniques ◽  
X Ray Diffraction ◽  
Major Health Problem ◽  
X Ray ◽  
Gallbladder Stones ◽  
Pure Cholesterol ◽  
Scanning Electron

Aim and Objective: Formation of the gallbladder stones is a common disease and a major health problem. The present study aimed to identify the structures of the most common types of gallbladder stones using X-ray spectroscopic techniques, which provide information about the process of stone formation. Material and Method: Phase and elemental compositions of pure cholesterol and mixed gallstones removed from gallbladders of patients were studied using energy-dispersive X-ray spectroscopy combined with scanning electron microscopy analysis and X-ray diffraction. Results: The crystal structures of gallstones which coincide with standard patterns were confirmed by X-ray diffraction. Plate-like cholesterol crystals with laminar shaped and thin layered structures were clearly observed for gallstone of pure cholesterol by scanning electron microscopy; it also revealed different morphologies from mixed cholesterol stones. Elemental analysis of pure cholesterol and mixed gallstones using energy-dispersive X-ray spectroscopy confirmed the different formation processes of the different types of gallstones. Conclusion: The method of fast and reliable X-ray spectroscopic techniques has numerous advantages over the traditional chemical analysis and other analytical techniques. The results also revealed that the X-ray spectroscopy technique is a promising technique that can aid in understanding the pathogenesis of gallstone disease.

scholarly journals Preliminary Study of the Targeted Cleaning of an Artificial Gypsum Layer on White Marble

Coatings ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 37
Author(s):  
Yan Liu ◽  
Taoling Dong ◽  
Kun Zhang ◽  
Fuwei Yang ◽  
Liqin Wang
Keyword(s):  
Electron Microscopy ◽  
Barium Carbonate ◽  
Color Difference ◽  
X Ray Diffraction ◽  
White Marble ◽  
Capillary Suction ◽  
Sulfate Ions ◽  
X Ray ◽  
Preliminary Study ◽  
Scanning Electron

Targeting cleaning of the artificial gypsum layer on white marble was studied. It was conducted by means of the specific depletion of the calcium and sulfate ions by the barium carbonate scavenger, which led to the continuous dissolution and clearance of gypsum layer. The cleaning effect was evaluated by scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX), X-ray diffraction (XRD), capillary suction, and color difference measurement. By this method, only the gypsum layer was cleared away and the carbonate substrate of marble was left intact at the same time. This method will be highly useful for the conservation of marble relics from surface weathering.

scholarly journals Analytical study of Buddha sculptures in Jingyin temple of Taiyuan, China

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Xiaojian Bai ◽  
Chen Jia ◽  
Zhigen Chen ◽  
Yuxuan Gong ◽  
Huwei Cheng ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Analytical Study ◽  
Energy Dispersive Spectrometry ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Ancient China ◽  
X Ray ◽  
Unique Style ◽  
Scanning Electron

AbstractWith exquisite design and unique style, the painted sculptures of Tutang Buddha and two attendants Buddha in Jingyin Temple are precious cultural heritages of China. The sculpture of Tutang Buddha, which was carved from a mound and painted by ancient craftsmen, was rarely found in ancient China. However, due to natural and human factors, the sculptures were severely damaged. Obviously, they require urgent and appropriate protection and restoration. In this study, samples taken from the sculptures were analysed through multiple analytical techniques, including scanning electron microscopy with energy dispersive spectrometry (SEM–EDS), Raman spectroscopy, X-ray diffraction (XRD), optical microscopy (OM) and granulometry. The analysis results enable us to infer the techniques used by the craftsmen in making the sculptures and provide a reliable evidence for the conservation and future protection of these and similar sculptures.

Sign in / Sign up

Export Citation Format

Share Document