scholarly journals Vibration Characteristics of Roundabout Swing of HAWT Wind Wheel

2016 ◽  
Vol 2016 ◽  
pp. 1-10
Author(s):  
Jian-long Ma ◽  
Pei-lin Li ◽  
Jian-wen Wang ◽  
Liu Yang ◽  
Yan-qi Zhang
Keyword(s):  
Horizontal Axis ◽  
Modal Testing ◽  
Shear Stresses ◽  
Horizontal Axis Wind Turbine ◽  
Primary Determinant ◽  
Vibration Stress ◽  
Horizontal Axis Wind Turbines ◽  
Natural Vibration Mode ◽  
The Relationship

Modal testing was used to show that the roundabout swing was a natural vibration mode of the wind wheel of a horizontal-axis wind turbine (HAWT). During the vibration, the blade root was simultaneously subjected to bending and rotary shear stresses. A method for indirect testing and determination of the dynamic frequencies of the typical vibrations of the wind wheel was developed, based on the frequency-holding characteristic of each subsignal during the transmission of the multiple mixed-vibration signals. The developed method enabled simple and accurate acquisition of the dynamic frequencies without destruction of the flow and structural fields. The dynamic vibration stress of the roundabout swing was found to be significantly stronger than those of the first- and second-order flexural vibrations of the blades. By a combination of numerical simulations and tests, it was determined that the pneumatic circumferential force was the primary determinant of the roundabout swing vibration frequencies, the relationship being quadratic. The roundabout swing vibration potentially offers new explanations and analytical pathways regarding the behavior of horizontal-axis wind turbines, which have been found to be frequently involved in fatigue-damage accidents within periods shorter than their design lives.

Calculating the aerodynamics of vertical axis wind turbines

2012 ◽  
Vol 34 (3) ◽  
pp. 169-184 ◽  
Author(s):  
Hoang Thi Bich Ngoc
Keyword(s):  
Wind Turbine ◽  
Incidence Angle ◽  
Vertical Axis ◽  
Rotor Blades ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbine ◽  
Velocity Triangle ◽  
Relationship Of ◽  
The Relationship

Vertical axis wind turbine technology has been applied last years, very long after horizontal axis wind turbine technology. Aerodynamic problems of vertical axis wind machines are discussible. An important problem is the determination of the incidence law in the interaction between wind and rotor blades. The focus of the work is to establish equations of the incidence depending on the blade azimuth, and to solve them. From these results, aerodynamic torques and power can be calculated. The incidence angle is a parameter of velocity triangle, and both the factors depend not only on the blade azimuth but also on the ratio of rotational speed and horizontal speed. The built computational program allows theoretically selecting the relationship of geometric parameters of wind turbine in accordance with requirements on power, wind speed and installation conditions.

scholarly journals Study and Design of a Horizontal Axis Wind Turbine (0.5 kW) Using Software Solid Works

2021 ◽  
pp. 1-17
Author(s):  
Hagninou E. V. Donnou ◽  
Drissa Boro ◽  
Jean Noé Fabiyi ◽  
Marius Tovoeho ◽  
Aristide B. Akpo
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wedge Angle ◽  
Three Dimensional ◽  
Synchronous Generator ◽  
Horizontal Axis ◽  
Geometrical Shape ◽  
Horizontal Axis Wind Turbine ◽  
Horizontal Axis Wind Turbines ◽  
Lift And Drag

In the present work, the study and design of a horizontal axis wind turbine suitable for the Cotonou site were investigated on the coast of Benin. A statistical study using the Weibull distribution was carried out on the hourly wind data measured at 10 m from the ground by the Agency for Air Navigation Safety in Africa and Madagascar (ASECNA) over the period from January 1981 to December 2014. Then, the models, techniques, tools and approaches used to design horizontal axis wind turbines were presented and the wind turbine components characteristics were determined. The numerical design and assembly of these components were carried out using SolidWorks software. The results revealed that the designed wind turbine has a power of 571W. It is equipped with a permanent magnet synchronous generator and has three aluminum blades with NACA 4412 biconvex asymmetrical profile. The values obtained for the optimum coefficient of lift and drag are estimated at 1.196 and 0.0189 respectively. The blades are characterised by an attack optimum angle estimated at 6° and the wedge angle at 5°. Their length is 2.50 m and the maximum thickness is estimated at 0.032 m for a rope length of 0.27 m. The wind turbine efficiency is 44%. The computer program designed on SolidWorks gives three-dimensional views of the geometrical shape of the wind turbine components and their assembly has allowed to visualize the compact shape of the wind turbine after export via its graphical interface. The energy quantity that can be obtained from the wind turbine was estimated at 2712,718 kWh/year. This wind turbine design study is the first of its kind for the study area. In order to reduce the technological dependence and the import of wind energy systems, the results of this study could be used to produce lower cost wind energy available on our study site.

scholarly journals New airfoils for micro horizontal-axis wind turbines

2021 ◽  
Author(s):  
Manoj Kumar Chaudhary ◽  
◽  
S. Prakash ◽  
Keyword(s):  
Reynolds Number ◽  
Wind Turbines ◽  
Low Reynolds Number ◽  
Horizontal Axis ◽  
Speed Ratio ◽  
Maximum Output ◽  
Horizontal Axis Wind Turbine ◽  
Horizontal Axis Wind Turbines ◽  
Low Reynolds ◽  
Bem Theory

In this study, small horizontal-axis wind turbine blades operating at low wind speeds were optimized. An optimized blade design method based on blade element momentum (BEM) theory was used. The rotor radius of 0.2 m, 0.4 m and 0.6 m and blade geometry with single (W1 & W2) and multistage rotor (W3) was examined. MATLAB and XFoil programs were used to implement to BEM theory and devise a six novel airfoil (NAF-Series) suitable for application of small horizontal axis wind turbines at low Reynolds number. The experimental blades were developed using the 3D printing additive manufacturing technique. The new airfoils such as NAF3929, NAF4420, NAF4423, NAF4923, NAF4924, and NAF5024 were investigated using XFoil software at Reynolds numbers of 100,000. The investigation range included tip speed ratios from 3 to 10 and angle of attacks from 2° to 20°. These parameters were varied in MATLAB and XFoil software for optimization and investigation of the power coefficient, lift coefficient, drag coefficient and lift-to-drag ratio. The cut-in wind velocity of the single and multistage rotors was approximately 2.5 & 3 m/s respectively. The optimized tip speed ratio, axial displacement and angle of attack were 5.5, 0.08m & 6° respectively. The proposed NAF-Series airfoil blades exhibited higher aerodynamic performances and maximum output power than those with the base SG6043 and NACA4415 airfoil at low Reynolds number.

scholarly journals Techniques for the Determination of Local Dynamic Pressure and Angle of Attack on a Horizontal Axis Wind Turbine

10.2172/61151 ◽  
1995 ◽  
Author(s):  
Derek E. Shipley ◽  
Mark S. Miller ◽  
Michael C. Robinson ◽  
Marvin W. Luttges ◽  
David A. Simms
Keyword(s):  
Wind Turbine ◽  
Dynamic Pressure ◽  
Angle Of Attack ◽  
Horizontal Axis ◽  
Local Dynamic ◽  
Horizontal Axis Wind Turbine

scholarly journals Experimental and Numerical Analysis of the Dynamical Behavior of a Small Horizontal-Axis Wind Turbine under Unsteady Conditions: Part I

Machines ◽  
2018 ◽  
Vol 6 (4) ◽  
pp. 52 ◽  
Author(s):  
Francesco Castellani ◽  
Davide Astolfi ◽  
Matteo Becchetti ◽  
Francesco Berno
Keyword(s):  
Control System ◽  
Wind Turbine ◽  
Dynamical Behavior ◽  
Urban Environments ◽  
Horizontal Axis ◽  
Test Case ◽  
Complex Flow ◽  
Horizontal Axis Wind Turbine ◽  
Horizontal Axis Wind Turbines ◽  
Unsteady Conditions

An efficient and reliable exploitation of small horizontal-axis wind turbines (HAWT) is a complex task: these kinds of devices actually modulate strongly variable loads with rotational speeds of the order of hundreds of revolutions per minute. The complex flow conditions to which small HAWTs are subjected in urban environments (sudden wind direction changes, considerable turbulence intensity, gusts) make it very difficult for the wind turbine control system to optimally balance the power and the load. For these reasons, it is important to comprehend and characterize the behavior of small HAWTs under unsteady conditions. On these grounds, this work is devoted to the formulation and realization of controlled unsteady test conditions for small HAWTs in the wind tunnel. The selected test case is a HAWT having 3 kW of maximum power and 2 m of rotor diameter: in this work, this device is subjected to oscillating wind time series, with a custom period. The experimental analysis allows therefore to characterize how unsteadiness is amplified moving from the primary resource (the wind) through the rotor revolutions per minute to final output (the power), in terms of delay and amplitude magnification. This work also includes a numerical characterization of the problem, by means of aeroelastic simulations performed with the FAST software. The comparison between experiments and numerical model supports the fact that the fast transitions are mainly governed by the aerodynamic and mechanical parameters: therefore, the aeroelastic modeling of a small HAWT can be useful in the developing phase to select appropriately the design and the control system set up.

Analysis on Aerodynamic Performance of Horizontal Axis Wind Turbine Based on Nonlinear Wake Model

2013 ◽  
Vol 448-453 ◽  
pp. 1716-1720
Author(s):  
Rui Yang ◽  
Jiu Xin Wang ◽  
Sheng Long Zhang
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Optimization Design ◽  
Aerodynamic Performance ◽  
Horizontal Axis ◽  
Wake Vortex ◽  
Horizontal Axis Wind Turbine ◽  
Horizontal Axis Wind Turbines ◽  
Wake Model ◽  
Induced Velocity

A computational method based on nonlinear wake model was established for horizontal axis wind turbines aerodynamic performance prediction. This method makes use of finite difference method to solve the integral differential equation of the model, the induced velocity of wake vortex can be calculated from equations and compared with the induced velocity of wake vortex in linear model. The comparison between the calculated results of wind turbine under axis flow condition, including tip vortex geometry and aerodynamic performance, and available experimental data shows that this method is suitable for wind turbine aerodynamic performance analysis. Finally, a series of numerical calculations were made to investigate the change of wake geometry and aerodynamic performance of the wind turbine when yawing and pitch angle increasing, which provide foundations for aerodynamic optimization design of horizontal axis wind turbines.

scholarly journals Observation of the Starting and Low Speed Behavior of Small Horizontal Axis Wind Turbine

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Sikandar Khan ◽  
Kamran Shah ◽  
Izhar-Ul-Haq ◽  
Hamid Khan ◽  
Sajid Ali ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Starting Time ◽  
Speed Range ◽  
Horizontal Axis Wind Turbines ◽  
Starting Torque ◽  
High Angles Of Attack

This paper describes the starting behavior of small horizontal axis wind turbines at high angles of attack and low Reynolds number. The unfavorable relative wind direction during the starting time leads to low starting torque and more idling time. Wind turbine models of sizes less than 5 meters were simulated at wind speed range of 2 m/s to 5 m/s. Wind turbines were modeled in Pro/E and based on the optimized designs given by MATLAB codes. Wind turbine models were simulated in ADAMS for improving the starting behavior. The models with high starting torques and less idling times were selected. The starting behavior was successfully improved and the optimized wind turbine models were able to produce more starting torque even at wind speeds less than 5 m/s.

Power Augmentation Effects of a Horizontal Axis Wind Turbine With a Tip Vane—Part 1: Turbine Performance and Tip Vane Configuration

1994 ◽  
Vol 116 (2) ◽  
pp. 287-292 ◽  
Author(s):  
Yukimaru Shimizu ◽  
Takaya Yoshikawa ◽  
Shinji Matsumura
Keyword(s):  
Wind Turbine ◽  
Output Power ◽  
Horizontal Axis ◽  
Experimental Results ◽  
Horizontal Axis Wind Turbine ◽  
Turbine Performance ◽  
Percent Increase ◽  
Maximum Improvement ◽  
The Relationship

This paper describes the experimental results of output power augmentation of a horizontal axis wind turbine with a tip vane. In order to find the relationship between the performance of the turbine and the configuration of the tip vane, various types and sizes were used. It was found that V-type and S-type tip vanes can improve turbine performance. Also, the dimensions of V- and S-type tip vanes were investigated. The maximum improvement achieved was a 25 percent increase in power in an existing wind turbine without a tip vane.

scholarly journals Establishing a robust testing approach for displacement measurement on a rotating horizontal-axis wind turbine

2018 ◽  
Vol 3 (1) ◽  
pp. 301-311
Author(s):  
Nadia Najafi ◽  
Allan Vesth
Keyword(s):  
Wind Turbine ◽  
Camera Calibration ◽  
Wind Turbines ◽  
Calibration Method ◽  
Horizontal Axis ◽  
Tracking Algorithm ◽  
Displacement Measurement ◽  
Horizontal Axis Wind Turbine ◽  
Damage And Failure ◽  
Horizontal Axis Wind Turbines

Abstract. Health monitoring by conventional sensors like accelerometers or strain gauges becomes challenging for large rotating structures due to the issues with feasibility, sensing and data transmission. In addition, acceleration measurements have low capability of presenting very small frequencies, which happen very often for large structures (for instance, frequencies between 0.2 and 0.5 Hz in horizontal-axis wind turbines). By contrast, displacement measurement using stereo vision is rapid, non-contacting and distributed over the structure. The sensors are cheaper and more easily applied to many places on the object to be measured. Horizontal-axis wind turbines are one of the most important large rotating structures and need to be measured and monitored in time to prevent damage and failure, and the blade tip position is one of the key parameters to measure in order to prevent the blade hitting the turbine tower. This paper presents a clearly described and easily applicable procedure for measuring the displacement on the components of a rotating horizontal-axis wind turbine with stereophotogrammetry. Paper markers have been applied on the rotor and tower of a scaled-down horizontal-axis wind turbine model in the workshop and the displacement measurement method has been demonstrated by measuring displacement during operation. The method is mainly developed in two parts: (1) camera calibration and (2) tracking algorithm. We introduce an efficient camera calibration method for measurement in large fields of view, which has always been a challenge. This method is easy and practical and offers better accuracy compared with 2-D traditional camera calibration. The tracking algorithm also works successfully and is able to track the points during rotation within the measurement time. Finally, the accuracy analysis has been conducted and has shown better accuracy of the new calibration method compared with 2-D traditional camera calibration.

Sign in / Sign up

Export Citation Format

Share Document