scholarly journals An Improved Generalized Method for Evaluation of Parameters, Modeling, and Simulation of Photovoltaic Modules

2017 ◽  
Vol 2017 ◽  
pp. 1-19 ◽  
Author(s):  
Vandana Jha ◽  
Uday Shankar Triar
Keyword(s):  
Modeling And Simulation ◽  
Standard Test ◽  
Unknown Parameters ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Test Conditions ◽  
Pv Modules ◽  
Evaluation Of Parameters ◽  
Output Characteristics ◽  
Matlab Programming

This paper proposes an improved generalized method for evaluation of parameters, modeling, and simulation of photovoltaic modules. A new concept “Level of Improvement” has been proposed for evaluating unknown parameters of the nonlinear I-V equation of the single-diode model of PV module at any environmental condition, taking the manufacturer-specified data at Standard Test Conditions as inputs. The main contribution of the new concept is the improvement in the accuracy of values of evaluated parameters up to various levels and is based on mathematical equations of PV modules. The proposed evaluating method is implemented by MATLAB programming and, for demonstration, by using the values of parameters of the I-V equation obtained from programming results, a PV module model is build with MATLAB. The parameters evaluated by the proposed technique are validated with the datasheet values of six different commercially available PV modules (thin film, monocrystalline, and polycrystalline) at Standard Test Conditions and Nominal Operating Cell Temperature Conditions. The module output characteristics generated by the proposed method are validated with experimental data of FS-270 PV module. The effects of variation of ideality factor and resistances on output characteristics are also studied. The superiority of the proposed technique is proved.

scholarly journals Performance of Photovoltaic Modules of Different Solar Cells

2013 ◽  
Vol 2013 ◽  
pp. 1-13 ◽  
Author(s):  
Ankita Gaur ◽  
G. N. Tiwari
Keyword(s):  
Solar Cells ◽  
Minimum Cost ◽  
Electrical Energy ◽  
Energy Generation ◽  
Standard Test ◽  
Photovoltaic Modules ◽  
Test Conditions ◽  
Pv Modules ◽  
Electrical Energy Generation ◽  
Made In

In this paper, an attempt of performance evaluation of semitransparent and opaque photovoltaic (PV) modules of different generation solar cells, having the maximum efficiencies reported in the literature at standard test conditions (STC), has been carried out particularly for the months of January and June. The outdoor performance is also evaluated for the commercially available semitransparent and opaque PV modules. Annual electrical energy, capitalized cost, annualized uniform cost (unacost), and cost per unit electrical energy for both types of solar modules, namely, semitransparent and opaque have also been computed along with their characteristics curves. Semitransparent PV modules have shown higher efficiencies compared to the opaque ones. Calculations show that for the PV modules made in laboratory, CdTe exhibits the maximum annual electrical energy generation resulting into minimum cost per unit electrical energy, whereas a-Si/nc-Si possesses the maximum annual electrical energy generation giving minimum cost per unit electrical energy when commercially available solar modules are concerned. CIGS has shown the lowest capitalized cost over all other PV technologies.

scholarly journals Improved Hybrid Parameters Extraction of a PV Module Using a Moth Flame Algorithm

Electronics ◽  
2021 ◽  
Vol 10 (22) ◽  
pp. 2798
Author(s):  
Safi Allah Hamadi ◽  
Aissa Chouder ◽  
Mohamed Mounir Rezaoui ◽  
Saad Motahhir ◽  
Ameur Miloud Kaddouri
Keyword(s):  
Extraction Procedure ◽  
Parameter Extraction ◽  
Standard Test ◽  
Maximum Power ◽  
Model Parameters ◽  
Unknown Parameters ◽  
Operating Condition ◽  
Pv Module ◽  
Test Conditions ◽  
Parameters Extraction

The identification of actual photovoltaic (PV) model parameters under real operating condition is a crucial step for PV engineering. An accurate and trusted model depends mainly on the accuracy of the model parameters. In this paper, an accurate and enhanced methodology is intended for PV module parameters extraction in outdoor conditions. The proposed methodology combines numerical methods and analytical formulations of the one diode model to derive the five unknown parameters in any operating condition of irradiance and temperature. First, the measured I-V curves at a random weather condition are translated to standard test conditions (i.e., G = 1000 W/m2, T = 25 °C), using translation equations. The second step consists of using an optimization algorithm namely the moth flame algorithm (MFO) to find out the five parameters at standard test conditions. Analytical formulations, at a random irradiance and temperature, are then used to express the unknown parameters at any irradiance and temperature. The proposed approach is validated under outdoor conditions against measured I-V curves at different irradiances and temperatures. The validation has also been performed under dynamic operation where the measured maximum power point coordinates (MPP) are compared to the predicted maximum power points. The obtained results from the adopted hybrid methodology confirm the accuracy of the parameter extraction procedure.

Investigation on the accurate parameter estimation of photovoltaic (PV) module based on simplified two-diode model

2016 ◽  
Vol 13 (3) ◽  
pp. 225-233
Author(s):  
B. Chitti Babu ◽  
Suresh Gurjar ◽  
Tomas Cermak
Keyword(s):  
Parameter Estimation ◽  
Design Methodology ◽  
Standard Test ◽  
Computational Time ◽  
Unknown Parameters ◽  
Partial Shading ◽  
Content Type ◽  
Pv Module ◽  
Test Conditions ◽  
Proposed Model

Purpose This paper aims to present a detailed investigation on the parameter estimation of a photovoltaic (PV) module by using a simplified two-diode model. Design/methodology/approach The studied PV module in this paper resembles an ideal two-diode model, and to reduce the computational time, the proposed model has a photocurrent source and two ideal-diodes and neglects the series and shunt resistances. Hence, for calculating the unknown parameters, only four parameters are required from the datasheet. Moreover, the studied model is simple and uses an easy modeling approach which is free from complexities. Findings The performance of the PV module is analyzed under non-standard test conditions by considering partial shading at different shaded levels, and it is found that the model has less computational time and gives accurate results. Originality/value The usefulness of this PV model is demonstrated with the help of several illustrative figures, and the performance of the PV module is evaluated.

A novel modeling approach to predict the output performance of photovoltaic modules under different environmental conditions

SIMULATION ◽  
2018 ◽  
Vol 94 (10) ◽  
pp. 861-872 ◽  
Author(s):  
Mohamed Saleem Abdul Kareem ◽  
Manimaran Saravanan
Keyword(s):  
Environmental Conditions ◽  
Series Resistance ◽  
Standard Test ◽  
Maximum Power ◽  
Unknown Parameters ◽  
Shunt Resistance ◽  
Output Performance ◽  
Pv Module ◽  
Current Saturation ◽  
Pv Modules

In this paper, an improved mathematical model of a single-diode photovoltaic (PV) module has been developed to predict the maximum power of the PV modules produced by different PV technologies, such as mono crystalline, multi crystalline, and thin film, under varying environmental conditions. The current–voltage characteristic equation of the PV module is used to extract the PV module’s unknown parameters, such as light generated current, saturation current, ideality factor, series resistance, and shunt resistance at standard test condition (STC). In the proposed PV model, numerical methods are used to calculate the parameters of the PV module at STC, by introducing new equations to estimate the value of series resistance and shunt resistance. By introducing new equations IMPP and VMPP, the maximum power of different PV modules manufactured by various PV technologies at different environmental conditions is then found. In the proposed PV model, the percentage relative error obtained at maximum power is calculated and the experimental results are compared with the models that exist in the literature for different PV modules. The maximum power obtained by the proposed PV model is much closer to that obtained by the Sandia model and Ishaque two-diode model. Furthermore, the output performance of the developed PV model has close agreement with the experimentally obtained data and it is verified practically.

scholarly journals Temperature on PV Module Performance and its Latest Mitigation Techniques: A Review

2021 ◽  
Vol 9 (6) ◽  
pp. 651-658
Keyword(s):  
Open Circuit Voltage ◽  
Operating Temperature ◽  
Electrical Energy ◽  
Standard Test ◽  
Open Circuit ◽  
Solar Insolation ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Test Conditions ◽  
Module Performance

Photovoltaic modules (PVM) output power is sensitive to fluctuations in temperature and the concentration of solar insolation during sustained disclosure. The 20% of solar insolation will be converted into useful electrical energy, while the rest will be dissipated in the form of heat, which in rotate will increase the operating heat of the PVM and it negatively affects the open circuit voltage (Voc), resulting in a decrease in the power alteration productivity and an irreversible rate of cell deprivation. Appropriate cooling techniques are therefore crucial to preserve the operating temperature of the module under standard test conditions (STC). There are two different methods for cooling PVMs, namely active and passive these methods are subdivided into different techniques which are discussed one by one in literature review; in this paper the techniques for cooling PVMs are comprehensively reviewed

scholarly journals Migration of Sn and Pb from Solder Ribbon onto Ag Fingers in Field-Aged Silicon Photovoltaic Modules

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Wonwook Oh ◽  
Seongtak Kim ◽  
Soohyun Bae ◽  
Nochang Park ◽  
Sung-Il Chan ◽  
...  
Keyword(s):  
Solar Cells ◽  
Galvanic Corrosion ◽  
Solar Irradiation ◽  
Photovoltaic Modules ◽  
Si Solar Cells ◽  
Test Conditions ◽  
Pv Modules ◽  
Moisture Condensation ◽  
Acceleration Test ◽  
Light Induced Plating

We investigated the migration of Sn and Pb onto the Ag fingers of crystalline Si solar cells in photovoltaic modules aged in field for 6 years. Layers of Sn and Pb were found on the Ag fingers down to the edge of the solar cells. This phenomenon is not observed in a standard acceleration test condition for PV modules. In contrast to the acceleration test conditions, field aging subjects the PV modules to solar irradiation and moisture condensation at the interface between the solar cells and the encapsulant. The solder ribbon releases Sn and Pb via repeated galvanic corrosion and the Sn and Pb precipitate on Ag fingers due to the light-induced plating under solar irradiation.

scholarly journals A Study of Optimal Specifications for Light Shelves with Photovoltaic Modules to Improve Indoor Comfort and Save Building Energy

2021 ◽  
Vol 18 (5) ◽  
pp. 2574
Author(s):  
Heangwoo Lee ◽  
Xiaolong Zhao ◽  
Janghoo Seo
Keyword(s):  
Energy Savings ◽  
Building Energy ◽  
Energy Performance ◽  
Building Energy Efficiency ◽  
Efficiency Change ◽  
Photovoltaic Modules ◽  
Heating And Cooling ◽  
Pv Module ◽  
Pv Modules ◽  
Indoor Comfort

Recent studies on light shelves found that building energy efficiency could be maximized by applying photovoltaic (PV) modules to light shelf reflectors. Although PV modules generate a substantial amount of heat and change the consumption of indoor heating and cooling energy, performance evaluations carried out thus far have not considered these factors. This study validated the effectiveness of PV module light shelves and determined optimal specifications while considering heating and cooling energy savings. A full-scale testbed was built to evaluate performance according to light shelf variables. The uniformity ratio was found to improve according to the light shelf angle value and decreased as the PV module installation area increased. It was determined that PV modules should be considered in the design of light shelves as their daylighting and concentration efficiency change according to their angles. PV modules installed on light shelves were also found to change the indoor cooling and heating environment; the degree of such change increased as the area of the PV module increased. Lastly, light shelf specifications for reducing building energy, including heating and cooling energy, were not found to apply to PV modules since PV modules on light shelf reflectors increase building energy consumption.

scholarly journals Mathematical Method for Parameters Calculation of electric Characteristic of Photovoltaic Module

2018 ◽  
Vol 3 (4) ◽  
pp. 190-200
Author(s):  
B. Benabdelkrim ◽  
A. Benatillah
Keyword(s):  
Standard Test ◽  
Photovoltaic Module ◽  
Unknown Parameters ◽  
Efficient Manner ◽  
Electric Characteristic ◽  
Precise Knowledge ◽  
Current Voltage ◽  
Pv Modules ◽  
Numerical Approaches ◽  
Parameters Calculation

The study of photovoltaic systems (PV) in an efficient manner requires a precise knowledge of the I-V characteristic curves of PV modules. An accurate current-voltage (I-V) model of PV modules is inherently implicit and non-linear and calls for iterative computations to obtain an analytical expression of current as a function of voltage. In this paper, numerical approaches are proposed to forecast the PV modules performance for engineering applications. The proposed approaches were implemented in a Matlab script and the results have been compared with the datasheet values provided by manufacturers in standard test conditions (STC). These approaches permit to extract the unknown parameters and also allow quantifying the effects of module temperature and irradiance on key cells parameters. In this work, a comparative study of the performance characteristics for different modules thin films and solid is analyzed by a single-diode equivalent circuit using four- and five-parameter models and two diode model.

scholarly journals Performance evaluation of polycrystalline photovoltaic modules in a Guinea Savanna and Mangrove swamp

2021 ◽  
Vol 4 (1) ◽  
pp. 011-021
Author(s):  
Nsed Ayip Akonjom ◽  
John Iyang Umuji ◽  
Ukoette Jeremiah Ekah
Keyword(s):  
Relative Humidity ◽  
Solar Power ◽  
Solar Flux ◽  
Mangrove Swamp ◽  
Cross River State ◽  
Photovoltaic Modules ◽  
Power Meter ◽  
Guinea Savanna ◽  
Pv Module ◽  
Pv Modules

This central idea of this research is to investigate how voltage, current, power output and efficiency of polycrystalline photovoltaic (PV) modules installed in a Guinea Savanna and Mangrove Swamp is affected by temperature, relative humidity and irradiance. The study locations are Calabar (mangrove swamp) and Ogoja (guinea savanna), in Cross River State, Nigeria. Two polycrystalline PV modules of exact specification mounted on a platform one-metre-high above the ground were used. A digital solar power meter (SM206) and a digital solar flux meter (MS 6616) was used to monitor and measure solar power and solar flux reaching the PV modules. A digital hygrometer and thermometer (KT-908) were used to monitor and measure the relative humidity and ambient temperature level at the height of installation and a digital multimeter (M880C+) accompanied with a temperature sensor was used to monitor voltage, current and panel temperature values from the modules. Analysis of the collected data reveals that the efficiency of the modules were not constant throughout the day. However, a higher voltage production and efficiency level was obtained for the PV module installed in Ogoja than that installed in Calabar under their respective levels of relative humidity, temperature and irradiance.

Sign in / Sign up

Export Citation Format

Share Document