scholarly journals Time-Domain Analytical Expression for Near Fields of Arbitrarily Oriented Electric Dipole and Its Application

2017 ◽  
Vol 2017 ◽  
pp. 1-8
Author(s):  
Qian Yang ◽  
Bing Wei ◽  
Xinbo He ◽  
Minghao Gong
Keyword(s):  
Time Domain ◽  
Electric Dipole ◽  
Near Field ◽  
Wide Band ◽  
Frequency Transformation ◽  
Numerical Examples ◽  
Electromagnetic Problems ◽  
Time Frequency ◽  
The Time Domain ◽  
Analytical Expressions

The near fields of electric dipole are commonly used in wide-band analysis of complex electromagnetic problems. In this paper, we propose new near field time-domain expressions for electric dipole. The analytical expressions for the frequency-domain of arbitrarily oriented electric dipole are given at first; next we give the time-domain expressions by time-frequency transformation. The proposed expressions are used in hybrid TDIE/DGTD method for analysis of circular antenna with radome. The accuracy of the proposed algorithm is verified by numerical examples.

Separating Multiple Moving Sources by Microphone Array Signals for Wayside Acoustic Fault Diagnosis

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
Wei Xiong ◽  
Qingbo He ◽  
Zhike Peng
Keyword(s):  
Fault Diagnosis ◽  
Time Domain ◽  
Feature Matching ◽  
Matching Pursuit ◽  
Microphone Array ◽  
Time Frequency ◽  
Moving Sources ◽  
The Time Domain ◽  
Envelope Spectrum ◽  
Threshold Setting

Wayside acoustic defective bearing detector (ADBD) system is a potential technique in ensuring the safety of traveling vehicles. However, Doppler distortion and multiple moving sources aliasing in the acquired acoustic signals decrease the accuracy of defective bearing fault diagnosis. Currently, the method of constructing time-frequency (TF) masks for source separation was limited by an empirical threshold setting. To overcome this limitation, this study proposed a dynamic Doppler multisource separation model and constructed a time domain-separating matrix (TDSM) to realize multiple moving sources separation in the time domain. The TDSM was designed with two steps of (1) constructing separating curves and time domain remapping matrix (TDRM) and (2) remapping each element of separating curves to its corresponding time according to the TDRM. Both TDSM and TDRM were driven by geometrical and motion parameters, which would be estimated by Doppler feature matching pursuit (DFMP) algorithm. After gaining the source components from the observed signals, correlation operation was carried out to estimate source signals. Moreover, fault diagnosis could be carried out by envelope spectrum analysis. Compared with the method of constructing TF masks, the proposed strategy could avoid setting thresholds empirically. Finally, the effectiveness of the proposed technique was validated by simulation and experimental cases. Results indicated the potential of this method for improving the performance of the ADBD system.

scholarly journals A research on fiber-optic vibration pattern recognition based on time-frequency characteristics

2018 ◽  
Vol 10 (12) ◽  
pp. 168781401881346 ◽  
Author(s):  
Tabi Fouda Bernard Marie ◽  
Dezhi Han ◽  
Bowen An ◽  
Jingyun Li
Keyword(s):  
Pattern Recognition ◽  
Frequency Domain ◽  
Time Domain ◽  
Fiber Optic ◽  
Pattern Recognition Method ◽  
Recognition Method ◽  
Time Frequency ◽  
Mode Decomposition ◽  
Vibration Pattern ◽  
The Time Domain

To detect and recognize any type of events over the perimeter security system, this article proposes a fiber-optic vibration pattern recognition method based on the combination of time-domain features and time-frequency domain features. The performance parameters (event recognition, event location, and event classification) are very important and describe the validity of this article. The pattern recognition method is precisely based on the empirical mode decomposition of time-frequency entropy and center-of-gravity frequency. It implements the function of identifying and classifying the event (intrusions or non-intrusion) over the perimeter to secure. To achieve this method, the first-level prejudgment is performed according to the time-domain features of the vibration signal, and the second-level prediction is carried out through time-frequency analysis. The time-frequency distribution of the signal is obtained by empirical mode decomposition and Hilbert transform and then the time-frequency entropy and center-of-gravity frequency are used to form the time-frequency domain features, that is, combined with the time-domain features to form feature vectors. Multiple types of probabilistic neural networks are identified to determine whether there are intrusions and the intrusion types. The experimental results demonstrate that the proposed method is effective and reliable in identifying and classifying the type of event.

scholarly journals Recurrence Plot-Based Approach for Cardiac Arrhythmia Classification Using Inception-ResNet-v2

2021 ◽  
Vol 12 ◽  
Author(s):  
Hua Zhang ◽  
Chengyu Liu ◽  
Zhimin Zhang ◽  
Yujie Xing ◽  
Xinwen Liu ◽  
...  
Keyword(s):  
Cardiac Arrhythmia ◽  
Time Domain ◽  
Original Data ◽  
Classification Problem ◽  
Recurrence Plot ◽  
Two Dimensions ◽  
Time Frequency ◽  
Ecg Signals ◽  
Physiological Signal ◽  
The Time Domain

The present study addresses the cardiac arrhythmia (CA) classification problem using the deep learning (DL)-based method for electrocardiography (ECG) data analysis. Recently, various DL techniques have been utilized to classify arrhythmias, with one typical approach to developing a one-dimensional (1D) convolutional neural network (CNN) model to handle the ECG signals in the time domain. Although the CA classification in the time domain is very prevalent, current methods’ performances are still not robust or satisfactory. This study aims to develop a solution for CA classification in two dimensions by introducing the recurrence plot (RP) combined with an Inception-ResNet-v2 network. The proposed method for nine types of CA classification was tested on the 1st China Physiological Signal Challenge 2018 dataset. During implementation, the optimal leads (lead II and lead aVR) were selected, and then 1D ECG segments were transformed into 2D texture images by the RP approach. These RP-based images as input signals were passed into the Inception-ResNet-v2 for CA classification. In the CPSC, Georgia, and the PTB_XL ECG databases of the PhysioNet/Computing in Cardiology Challenge 2020, the RP-based method achieved an average F1-score of 0.8521, 0.8529, and 0.8862, respectively. The results suggested the excellent generalization ability of the proposed method. To further assess the performance of the proposed method, we compared the 2D RP-image-based solution with the published 1D ECG-based works on the same dataset. Also, it was compared with two traditional ECG transform into 2D image methods, including the time waveform of the ECG recordings and time-frequency images based on continuous wavelet transform (CWT). The proposed method achieved the highest average F1-score of 0.844, with only two leads of the 12-lead ECG original data, which outperformed other works. Therefore, the promising results indicate that the 2D RP-based method has a high clinical potential for CA classification using fewer lead ECG signals.

scholarly journals Orthogonal Time Sequency Multiplexing Modulation

2021 ◽  
Author(s):  
Tharaj Thaj ◽  
Emanuele Viterbo
Keyword(s):  
Time Domain ◽  
Orthogonal Frequency Division Multiplexing ◽  
High Performance ◽  
High Mobility ◽  
Low Complexity ◽  
Modulation Scheme ◽  
Frequency Space ◽  
Time Frequency ◽  
Single Carrier ◽  
The Time Domain

This paper proposes <i>orthogonal time sequency multiplexing</i> (OTSM), a novel single carrier modulation scheme based on the well known Walsh-Hadamard transform (WHT) combined with row-column interleaving, and zero padding (ZP) between blocks in the time-domain. The information symbols in OTSM are multiplexed in the delay and sequency domain using a cascade of time-division and Walsh-Hadamard (sequency) multiplexing. By using the WHT for transmission and reception, the modulation and demodulation steps do not require any complex multiplications. We then propose two low-complexity detectors: (i) a simpler non-iterative detector based on a single tap minimum mean square time-frequency domain equalizer and (ii) an iterative time-domain detector. We demonstrate, via numerical simulations, that the proposed modulation scheme offers high performance gains over orthogonal frequency division multiplexing (OFDM) and exhibits the same performance of orthogonal time frequency space (OTFS) modulation, but with lower complexity. In proposing OTSM, along with simple detection schemes, we offer the lowest complexity solution to achieving reliable communication in high mobility wireless channels, as compared to the available schemes published so far in the literature.

Analytical Expressions for Electromagnetic Fields Associated with the Inclined Lightning Channels in the Time Domain

2012 ◽  
Vol 40 (4) ◽  
pp. 414-438 ◽  
Author(s):  
Mahdi Izadi ◽  
Mohd Zainal Ab Kadir ◽  
Chandima Gomes ◽  
Wan Fatin Hamamah Wan Ahmad
Keyword(s):  
Electromagnetic Fields ◽  
Time Domain ◽  
The Time Domain ◽  
Analytical Expressions

scholarly journals A SFTD Algorithm for Optimizing the Performance of the Readout Strategy of Residence Time Difference Fluxgate

Sensors ◽  
2018 ◽  
Vol 18 (11) ◽  
pp. 3985 ◽  
Author(s):  
Siyu Chen ◽  
Yanzhang Wang ◽  
Jun Lin
Keyword(s):  
Residence Time ◽  
Time Domain ◽  
Signal To Noise Ratio ◽  
Low Frequency ◽  
Transformation Method ◽  
Time Difference ◽  
Single Frequency ◽  
Time Frequency ◽  
Frequency Magnetic Field ◽  
The Time Domain

Residence time difference (RTD) fluxgate sensor is a potential device to measure the DC or low-frequency magnetic field in the time domain. Nevertheless, jitter noise and magnetic noise severely affect the detection result. A novel post-processing algorithm for jitter noise reduction of RTD fluxgate output strategy based on the single-frequency time difference (SFTD) method is proposed in this study to boost the performance of the RTD system. This algorithm extracts the signal that has a fixed frequency and preserves its time-domain information via a time–frequency transformation method. Thereby, the single-frequency signal without jitter noise, which still contains the ambient field information in its time difference, is yielded. Consequently, compared with the traditional comparator RTD method (CRTD), the stability of the RTD estimation (in other words, the signal-to-noise ratio of residence time difference) has been significantly boosted with sensitivity of 4.3 μs/nT. Furthermore, the experimental results reveal that the RTD fluxgate is comparable to harmonic fluxgate sensors, in terms of noise floor.

scholarly journals Preliminary comparative assessment of PM10 hourly measurement results from new monitoring stations type using stochastic and exploratory methodology and models

2018 ◽  
Vol 28 ◽  
pp. 01010 ◽  
Author(s):  
Piotr Oskar Czechowski ◽  
Tomasz Owczarek ◽  
Artur Badyda ◽  
Grzegorz Majewski ◽  
Mariusz Rogulski ◽  
...  
Keyword(s):  
Time Domain ◽  
Comparative Assessment ◽  
Reference Station ◽  
Portable Devices ◽  
Annual Series ◽  
Time Frequency ◽  
Measurement Results ◽  
Key Issues ◽  
The Time Domain ◽  
Series Measurement

The paper presents selected preliminary stage key issues proposed extended equivalence measurement results assessment for new portable devices - the comparability PM10 concentration results hourly series with reference station measurement results with statistical methods. In article presented new portable meters technical aspects. The emphasis was placed on the comparability the results using the stochastic and exploratory methods methodology concept. The concept is based on notice that results series simple comparability in the time domain is insufficient. The comparison of regularity should be done in three complementary fields of statistical modeling: time, frequency and space. The proposal is based on model’s results of five annual series measurement results new mobile devices and WIOS (Provincial Environmental Protection Inspectorate) reference station located in Nowy Sacz city. The obtained results indicate both the comparison methodology completeness and the high correspondence obtained new measurements results devices with reference.

scholarly journals Time-Domain Investigation of Switchable Filter Wide-Band Antenna for Microwave Breast Imaging

Sensors ◽  
2020 ◽  
Vol 20 (15) ◽  
pp. 4302 ◽  
Author(s):  
Amir Haider ◽  
MuhibUr Rahman ◽  
Mahdi Naghshvarianjahromi ◽  
Hyung Seok Kim
Keyword(s):  
Time Domain ◽  
Breast Imaging ◽  
Wide Band ◽  
Tumor Detection ◽  
Ultra Wideband ◽  
Good Time ◽  
Area Network ◽  
Microwave Breast Imaging ◽  
The Time Domain ◽  
Domain Performance

This paper investigates the time-domain performance of a switchable filter impulse radio ultra-wideband (IR-UWB) antenna for microwave breast imaging applications. A miniaturized CPW-fed integrated filter antenna with switchable performance in the range of the Worldwide Interoperability for Microwave Access (WiMAX) and Wireless Local Area Network (WLAN) bands could operate well within a 3.0 to 11 GHz frequency range. The time-domain performance of the filter antenna was investigated in comparison to that of the designed reference wideband antenna. By comparing both antennas’ time-domain characteristics, it was seen that the switchable filter antenna had good time-domain resolution along with the frequency-domain operation. Additionally, the time-domain investigation revealed that the switchable filter wide-band antenna performed similarly to the reference wide band antenna. This antenna was also utilized for a tumor detection application, and it was seen that the switchable filter wide-band antenna could detect a miniaturized irregularly shaped tumor easily, which is quite promising. Such an antenna with a good time-domain resolution and tumor detection capability will be a good candidate and will find potential applications in microwave breast imaging.

scholarly journals Transmission compensated primary reflection retrieval in the data domain and consequences for imaging

Geophysics ◽  
2019 ◽  
Vol 84 (4) ◽  
pp. Q27-Q36 ◽  
Author(s):  
Lele Zhang ◽  
Jan Thorbecke ◽  
Kees Wapenaar ◽  
Evert Slob
Keyword(s):  
Thin Layer ◽  
Time Domain ◽  
Velocity Model ◽  
Original Data ◽  
Transmission Losses ◽  
Multiple Reflections ◽  
Data Set ◽  
Numerical Examples ◽  
The One ◽  
The Time Domain

We have developed a scheme that retrieves primary reflections in the two-way traveltime domain by filtering the data. The data have their own filter that removes internal multiple reflections, whereas the amplitudes of the retrieved primary reflections are compensated for two-way transmission losses. Application of the filter does not require any model information. It consists of convolutions and correlations of the data with itself. A truncation in the time domain is applied after each convolution or correlation. The retrieved data set can be used as the input to construct a better velocity model than the one that would be obtained by working directly with the original data and to construct an enhanced subsurface image. Two 2D numerical examples indicate the effectiveness of the method. We have studied bandwidth limitations by analyzing the effects of a thin layer. The presence of refracted and scattered waves is a known limitation of the method, and we studied it as well. Our analysis indicates that a thin layer is treated as a more complicated reflector, and internal multiple reflections related to the thin layer are properly removed. We found that the presence of refracted and scattered waves generates artifacts in the retrieved data.

Sign in / Sign up

Export Citation Format

Share Document