scholarly journals Seismic Vulnerability Assessment of Liquid Storage Tanks Isolated by Sliding-Based Systems

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Alexandros Tsipianitis ◽  
Yiannis Tsompanakis
Keyword(s):  
Large Scale ◽  
Seismic Vulnerability ◽  
Base Isolation ◽  
Cost Effective ◽  
Storage Tanks ◽  
Modes Of Failure ◽  
Liquid Storage ◽  
Near Fault Earthquakes ◽  
Friction Pendulum ◽  
The Cost

Liquid-filled tanks are effective storage infrastructure for water, oil, and liquefied natural gas (LNG). Many such large-scale tanks are located in regions with high seismicity. Therefore, very frequently base isolation technology has to be adopted to reduce the dynamic distress of storage tanks, preventing the structure from typical modes of failure, such as elephant-foot buckling, diamond-shaped buckling, and roof damage caused by liquid sloshing. The cost-effective seismic design of base-isolated liquid storage tanks can be achieved by adopting performance-based design (PBD) principles. In this work, the focus is given on sliding-based systems, namely, single friction pendulum bearings (SFPBs), triple friction pendulum bearings (TFPBs), and mainly on the recently developed quintuple friction pendulum bearings (QFPBs). More specifically, the study is focused on the fragility analysis of tanks isolated by sliding-bearings, emphasizing on isolators’ displacements due to near-fault earthquakes. In addition, a surrogate model has been developed for simulating the dynamic response of the superstructure (tank and liquid content) to achieve an optimal balance between computational efficiency and accuracy.

The effects of input earthquake characteristics on the nonlinear dynamic behavior of FPS isolated liquid storage tanks

2016 ◽  
Vol 24 (7) ◽  
pp. 1264-1282 ◽  
Author(s):  
Saman Bagheri ◽  
Mostafa Farajian
Keyword(s):  
Passive Control ◽  
Base Isolation ◽  
Ground Motions ◽  
Storage Tanks ◽  
Ground Acceleration ◽  
Pendulum System ◽  
Aspect Ratios ◽  
Liquid Storage ◽  
Isolation Systems ◽  
Friction Pendulum

There are several methods to reduce the seismic damages in liquid storage tanks. One of these methods is to use passive control devices, in particular seismic base isolators. Among the different base isolation systems, the Friction Pendulum System (FPS) whose period does not depend on the weight of the system is more appropriate for isolation of liquid storage tanks. The aim of this paper is to investigate the effects of peak ground acceleration (PGA) and pulselike characteristics of earthquakes on the seismic behavior of steel liquid storage tanks base isolated by FPS bearings. In addition, impact effects of the slider with the side retainer are investigated, as well as effects of tank aspect ratio, isolation period and friction coefficient. The obtained results of tanks with different aspect ratios indicate that the responses get more reduced due to isolation under far-field ground motions compared to near-fault ground motions. It is also seen that the response of a base isolated tank is affected when contact takes place with the side retainer of the FPS.

scholarly journals A Review on Terahertz Technologies Accelerated by Silicon Photonics

Nanomaterials ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1646
Author(s):  
Jingya Xie ◽  
Wangcheng Ye ◽  
Linjie Zhou ◽  
Xuguang Guo ◽  
Xiaofei Zang ◽  
...  
Keyword(s):  
Integrated Circuit ◽  
Silicon Photonics ◽  
Large Scale ◽  
Cost Effective ◽  
Single Chip ◽  
Photonic Integrated Circuit ◽  
Hybrid Silicon ◽  
The Cost ◽  
Silicon Based ◽  
Thz Applications

In the last couple of decades, terahertz (THz) technologies, which lie in the frequency gap between the infrared and microwaves, have been greatly enhanced and investigated due to possible opportunities in a plethora of THz applications, such as imaging, security, and wireless communications. Photonics has led the way to the generation, modulation, and detection of THz waves such as the photomixing technique. In tandem with these investigations, researchers have been exploring ways to use silicon photonics technologies for THz applications to leverage the cost-effective large-scale fabrication and integration opportunities that it would enable. Although silicon photonics has enabled the implementation of a large number of optical components for practical use, for THz integrated systems, we still face several challenges associated with high-quality hybrid silicon lasers, conversion efficiency, device integration, and fabrication. This paper provides an overview of recent progress in THz technologies based on silicon photonics or hybrid silicon photonics, including THz generation, detection, phase modulation, intensity modulation, and passive components. As silicon-based electronic and photonic circuits are further approaching THz frequencies, one single chip with electronics, photonics, and THz functions seems inevitable, resulting in the ultimate dream of a THz electronic–photonic integrated circuit.

An International Campaign for Agricultural and Livestock Genomics (CALG)

2002 ◽  
Vol 06 (24) ◽  
pp. 958-965
Author(s):  
Jun Yu ◽  
Jian Wang ◽  
Huanming Yang
Keyword(s):  
Large Scale ◽  
Cost Effective ◽  
Model Organisms ◽  
Environmental Biology ◽  
Cdna Sequences ◽  
Governmental Agencies ◽  
Technology Innovations ◽  
A Genome ◽  
Starting Point ◽  
The Cost

A coordinated international effort to sequence agricultural and livestock genomes has come to its time. While human genome and genomes of many model organisms (related to human health and basic biological interests) have been sequenced or plugged in the sequencing pipelines, agronomically important crop and livestock genomes have not been given high enough priority. Although we are facing many challenges in policy-making, grant funding, regional task emphasis, research community consensus and technology innovations, many initiatives are being announced and formulated based on the cost-effective and large-scale sequencing procedure, known as whole genome shotgun (WGS) sequencing that produces draft sequences covering a genome from 95 percent to 99 percent. Identified genes from such draft sequences, coupled with other resources, such as molecular markers, large-insert clones and cDNA sequences, provide ample information and tools to further our knowledge in agricultural and environmental biology in the genome era that just comes to its accelerated period. If the campaign succeeds, molecular biologists, geneticists and field biologists from all countries, rich or poor, would be brought to the same starting point and expect another astronomical increase of basic genomic information, ready to convert effectively into knowledge that will ultimately change our lives and environment into a greater and better future. We call upon national and international governmental agencies and organizations as well as research foundations to support this unprecedented movement.

scholarly journals THE MODELING OF SPILLS RESULTING FROM THE CATASTROPHIC FAILURE OF ABOVE GROUND STORAGE TANKS AND THE DEVELOPMENT OF MITIGATION

2008 ◽  
Vol 2008 (1) ◽  
pp. 949-956
Author(s):  
W. Atherton ◽  
J. W. Ash ◽  
R. M. Alkhaddar
Keyword(s):  
Large Scale ◽  
Structural Integrity ◽  
Oil Spills ◽  
Health And Safety ◽  
The Other ◽  
Catastrophic Failure ◽  
Storage Tanks ◽  
Modes Of Failure ◽  
Mode Of Failure ◽  
Mitigation Technique

ABSTRACT The risk of accidents involving the catastrophic failure of storage tanks is estimated to be low, in the region of 5 × l0−6 per tank year. However, recent accidents involving major oil spills at storage facilities located in Belgium (2004) along with USA and England (2005) have shown that tank failures do nevertheless occur. Causalities of such events vary; the consequences however are ordinarily the same, incurring environmental, financial and infrastructure losses. The normal mitigation technique employed to prevent such losses is secondary containment, usually in the form of a bund wall or earthen dyke. Researchers have investigated the reliability of such methods, examining the effects of tank failure, both theoretically and experimentally in terms of loss of containment. A United Kingdom Health and Safety Executive (HSE) review conducted in 1997 concluded that the then available data was limited and focussed attention on the work of Greenspan and Johansson (1981) and the later work of Trobojevic and Slater (1989). This led to the HSE commissioning Liverpool John Moores University (LIMU) in 2003 to undertake a large-scale spill-modelling program with the aim of quantifying the level of overtopping and the magnitudes of the dynamic pressures on the bunds. The study examined the effect of axisymmetric releases on a total of 96 tank and bund arrangements. Such losses have proven to be significant and in some cases the nature of the dynamic pressures has brought in to question the structural integrity of the bunds themselves. Research has since concentrated on modelling alternative modes of failure, such as directional releases, which could be considered to be the more common mode of failure likely to be encountered. The conclusions to this work have generated additional research to investigate possible methods of mitigation that could be incorporated into the design of facilities with the ultimate aim of further reducing losses in the event of tank failure. Two promising methods have been identified, one involving modification to the primary containment (tank) with the other being a change to the design of the profile of the secondary containment (bund wall).

scholarly journals Cost-Effectiveness Analysis of a Large-Scale Crèche Intervention to Prevent Child Drowning in Rural Bangladesh

2021 ◽  
Author(s):  
Y. Natalia Alfonso ◽  
Adnan A Hyder ◽  
Olakunle Alonge ◽  
Shumona Sharmin Salam ◽  
Kamran Baset ◽  
...  
Keyword(s):  
Cost Effectiveness ◽  
Societal Perspective ◽  
Large Scale ◽  
Operating Cost ◽  
Cost Effective ◽  
Economic Benefits ◽  
Program Cost ◽  
Rural Bangladesh ◽  
Life Years ◽  
The Cost

Abstract Drowning is the leading cause of death among children 12-59 months old in rural Bangladesh. This study evaluated the cost-effectiveness of a large-scale crèche intervention in preventing child drowning. Estimates of the effectiveness of the crèches was based on prior studies and the program cost was assessed using monthly program expenditures captured prospectively throughout the study period from two different implementing agencies. The study evaluated the cost-effectiveness from both a program and societal perspective. Results showed that from the program perspective the annual operating cost of a crèche was $416.35 (95%C.I.: $222 to $576), the annual cost per child was $16 (95%C.I.: $9 to $22) and the incremental-cost-effectiveness ratio (ICER) per life saved with the crèches was $17,803 (95%C.I.: $9,051 to $27,625). From the societal perspective (including parents time valued) the ICER per life saved was -$176,62 (95%C.I.: -$347,091 to -$67,684)—meaning crèches generated net economic benefits per child enrolled. Based on the ICER per disability-adjusted-life years averted from the societal perspective (excluding parents time), $2,020, the crèche intervention was cost-effective even when the societal economic benefits were ignored. Based on the evidence, the creche intervention has great potential for reducing child drowning at a cost that is reasonable.

New Zealand Research Applications of, and Developments in, Low Damage Technology for Steel Structures

2018 ◽  
Vol 763 ◽  
pp. 3-10 ◽  
Author(s):  
Gregory A. MacRae ◽  
George Charles Clifton ◽  
Michel Bruneau
Keyword(s):  
New Zealand ◽  
Large Scale ◽  
Base Isolation ◽  
Steel Structures ◽  
Small Towns ◽  
Steel Buildings ◽  
Construction Methods ◽  
Steel Framing ◽  
Friction Pendulum ◽  
Building Demolition

Over the past few years, the South Island of New Zealand has been subject to significant sequences of earthquake shaking. In particular, 2010-2011 events affected the city of Christchurch resulting in large scale demolition of buildings. Also, the recent and continuing 11/2016 events caused severe damage in the countryside, in small towns, and moderate damage further afield. This paper describes “low damage construction” methods being used in NZ, and especially in the Christchurch rebuild, to limit the possibility of building demolition in future large seismic events. The buildings used in the Christchurch rebuild are generally supported by structural steel framing. These steel buildings include BRB systems, EBF systems with replaceable active links, rocking systems, base isolation using friction pendulum systems and/or lead-rubber dissipaters, RBS beams, lead extrusion dissipaters, yielding flexural dissipaters, and friction connections. Concerns about a number of currently used systems are discussed.

A review of gasification of bio-oil for gas production

2019 ◽  
Vol 3 (7) ◽  
pp. 1600-1622 ◽  
Author(s):  
Ji-Lu Zheng ◽  
Ya-Hong Zhu ◽  
Ming-Qiang Zhu ◽  
Kang Kang ◽  
Run-Cang Sun
Keyword(s):  
Large Scale ◽  
Cost Effective ◽  
Gas Production ◽  
Commercial Production ◽  
Advanced Fuels ◽  
Bio Oil ◽  
Effective Transport ◽  
The Cost

The commercial production of advanced fuels based on bio-oil gasification could be promising because the cost-effective transport of bio-oil could promote large-scale implementation of this biomass technology.

scholarly journals Validation of variants using cost effective highresolution melting (HRM) analysis predicted from target re-sequencing in Eucalyptus

2020 ◽  
Vol 79 (2) ◽  
pp. 105-113
Author(s):  
Abdul Bari Muneera Parveen ◽  
Divya Lakshmanan ◽  
Modhumita Ghosh Dasgupta
Keyword(s):  
Next Generation Sequencing ◽  
Large Scale ◽  
Sequence Data ◽  
Cost Effective ◽  
Nucleotide Polymorphisms ◽  
Next Generation ◽  
Time Saving ◽  
Hrm Analysis ◽  
The Cost ◽  
Generation Sequencing

The advent of next-generation sequencing has facilitated large-scale discovery and mapping of genomic variants for high-throughput genotyping. Several research groups working in tree species are presently employing next generation sequencing (NGS) platforms for marker discovery, since it is a cost effective and time saving strategy. However, most trees lack a chromosome level genome map and validation of variants for downstream application becomes obligatory. The cost associated with identifying potential variants from the enormous amount of sequence data is a major limitation. In the present study, high resolution melting (HRM) analysis was optimized for rapid validation of single nucleotide polymorphisms (SNPs), insertions or deletions (InDels) and simple sequence repeats (SSRs) predicted from exome sequencing of parents and hybrids of Eucalyptus tereticornis Sm. ? Eucalyptus grandis Hill ex Maiden generated from controlled hybridization. The cost per data point was less than 0.5 USD, providing great flexibility in terms of cost and sensitivity, when compared to other validation methods. The sensitivity of this technology in variant detection can be extended to other applications including Bar-HRM for species authentication and TILLING for detection of mutants.

A cost effective approach to stormwater management? source control and distributed storage

1997 ◽  
Vol 36 (8-9) ◽  
pp. 307-311 ◽  
Author(s):  
R. Y. G. Andoh ◽  
C. Declerck
Keyword(s):  
Large Scale ◽  
Traditional Approach ◽  
Distributed Storage ◽  
Cost Effective ◽  
Source Control ◽  
Slowing Down ◽  
Surface Areas ◽  
Cost Effective Approach ◽  
Receiving Waters ◽  
The Cost

Rapid urbanisation and its consequent increase in impermeable surface areas and changes in land use has generally resulted in problems of flooding and heavy pollution of urban streams and other receiving waters. This has often been coupled with ground water depletion and a threat to water resources. The first part of this paper presents an alternative drainage philosophy and strategy which mimics nature's way by slowing down (attenuating) the movement of urban runoff. This approach results in cost-effective, affordable and sustainable drainage schemes. The alternative strategy can be described as one of prevention rather than cure by effecting controls closer to source rather than the traditional approach which results in the transfer of problems downstream, resulting in its cumulation and the need for large scale, centralised control. The second part describes a research project which has been launched in order to quantify the cost and operational benefits of source control and distributed storage. Details of the methodology of the modelling and simulation processes which are being followed to achieve this target are presented.

Sign in / Sign up

Export Citation Format

Share Document