scholarly journals Wear Behavior of the Multiheterostructured AZ91 Mg Alloy Prepared by ECAP and Aging

Scanning ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Bingqian Xu ◽  
Jiapeng Sun ◽  
Zhenquan Yang ◽  
Jing Han ◽  
Dan Song ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Wear Mechanism ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Cast Alloy ◽  
High Strength ◽  
Mg Alloy ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Strength And Ductility

The microstructure design based on the development of heterostructure provides a new way for high strength and ductility Mg alloys. However, the wear property, as an important service performance, of Mg alloys with heterostructure is scarcely investigated. In this work, a high strength and ductility AZ91 Mg alloy with multiheterostructure was prepared via a processing route combined industrial-scale equal channel angular pressing (ECAP) and aging. The multiheterostructure consists of the heterogeneous grain structure and heterogeneous precipitates. The dry sliding wear behavior of this multiheterostructured (MH) alloy is investigated compared to the as-cast alloy. The impacts of the applied load and duration time on the wear volume and coefficient of friction (COF) are analyzed, and the wear mechanism is further discussed. The result indicates that although the MH alloy exhibits high-desirable strength-ductility synergy, it shows a poorer wear resistance but a relatively lower COF compared to the as-cast alloy at the present condition. The wear mechanism of both alloys mainly involves abrasive wear, as well as mild adhesion, delamination, and oxidation. In comparison, the MH alloy shows relatively severe adhesion, delamination, and oxidation. The poor wear resistance of the MH alloy at the present dry sliding wear condition is linked to the abundant grain boundaries and fine precipitates. Therefore, one should reasonably use the MH Mg alloy considering the service conditions to seek advantages and avoid disadvantages.

Dry Sliding Wear Behavior of Fe-Ni-Mo-C-Cr Powder Sintered Structural Steel

2012 ◽  
Vol 433-440 ◽  
pp. 572-577
Author(s):  
Hua Chen ◽  
Hai Ying Sun ◽  
Zhan Kui Zhao ◽  
Zhi Long Chai
Keyword(s):  
Wear Resistance ◽  
Wear Mechanism ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Hot Forging ◽  
High Wear Resistance ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Delamination Wear ◽  
Cr System

Fe-Ni-Mo-C-Cr system powder metallurgy in the as-sintered was investigated on pin-on-rolling wear tester for their dry sliding wear behavior. The morphology of worn surfaces and wear mechanism were analysed by SEM. Results show the hot-forging deformation quenching and tempered considerably decreased the porosity and improved wear resistance, and compare with quenching microstructure, tempered microstructure has high wear resistance and match of strength-toughness. Fe-2.0Ni-0.4Mo-0.5C-0.6Cr alloy presented best wear characteristics. SEM observations of the worn surface revealed microploughing and plastic deformation and crack were the basic dry sliding wear morphology,and oxidative wear and delamination wear are dominant wear mechanism.

Study of Microstructure and Wear Behavior of T6 Heat Treated as Cast Al-25Mg2Si-2Cu Alloy

2015 ◽  
Vol 830-831 ◽  
pp. 358-361 ◽  
Author(s):  
D.G. Sondur ◽  
D.M. Goudar ◽  
D.G. Mallapur ◽  
G.B. Rudrakshi
Keyword(s):  
Wear Resistance ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Cast Alloy ◽  
Wear Test ◽  
Wear Behaviour ◽  
High Wear Resistance ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Heat Treated

In the present investigation, microstructural characteristics and dry sliding wear behaviour of T6 heat treated conventionally cast Al-25Mg2Si-2Cu alloy have been discussed. The as cast alloy was subjected to solutionizing at 500°C for 5h and isothermal aging treatment at 190°C for different aging times. The micro structural characterization was studied using Scanning Electron Microscope with EDS analysis. The microstructure of as cast alloy consists of intermetallics of coarse block like sharp edged β-(Mg2Si), θ-(Al2Cu) and Q-(Al-Mg-Cu-Si) in the form of Chinese scripts and needles distributed randomly in the Al-matrix. The microstructure of heat treated alloy shows spheroidization of β phase and fine precipitation of θ-(Al2Cu) and Q phases. The dry sliding wear test was carried out using pin-on-disc machine. Age hardened alloy exhibits high wear resistance and minimum coefficient of friction over the entire range of applied loads and sliding velocities. Furthermore, high wear resistance was observed in the under aged condition compared to over ageing conditions.

scholarly journals Effect of Necklace-Type Distribution of SiC Particles on Dry Sliding Wear Behavior of As-Cast AZ91D/SiCp Composites

Crystals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 296 ◽  
Author(s):  
Chao Sun ◽  
Nannan Lu ◽  
Huan Liu ◽  
Xiaojun Wang ◽  
Xiaoshi Hu ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Interface Bonding ◽  
Type Distribution ◽  
Wear Rates ◽  
Sic Particles ◽  
The Matrix

In this study, the dry sliding wear behaviors of SiC particle reinforced AZ91D matrix composites fabricated by stirring casting method were systematically investigated. The SiC particles in as-cast composites exhibited typical necklace-type distribution, which caused the weak interface bonding between SiC particles and matrix in particle-segregated zones. During dry sliding at higher applied loads, SiC particles were easy to debond from the matrix, which accelerated the wear rates of the composites. While at the lower load of 10 N, the presence of SiC particles improved the wear resistance. Moreover, the necklace-type distribution became more evident with the decrease of particle sizes and the increase of SiC volume fractions. Larger particles had better interface bonding with the matrix, which could delay the transition of wear mechanism from oxidation to delamination. Therefore, composites reinforced by larger SiC particles exhibited higher wear resistance. Similarly, owing to more weak interfaces in the composites with high content of SiC particles, more severe delamination occurred and the wear resistance of the composites was impaired.

scholarly journals Effect of Nanobainite Content on the Dry Sliding Wear Behavior of an Al-Alloyed High Carbon Steel with Nanobainitic Microstructure

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1618 ◽  
Author(s):  
Zhaohuan Song ◽  
Songhao Zhao ◽  
Tao Jiang ◽  
Junjie Sun ◽  
Yingjun Wang ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Carbon Steel ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Normal Load ◽  
High Carbon Steel ◽  
Peak Hardness ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
High Carbon

In this work, a multiphase microstructure consisting of nanobainte, martensite, undissolved spherical carbide, and retained blocky austenite has been prepared in an Al-alloyed high carbon steel. The effect of the amount of nanobainite on the dry sliding wear behavior of the steel is studied using a pin-on-disc tester with loads ranging from 25–75 N. The results show that, there is no significant differences in specific wear rate (SWR) for samples with various amounts of nanobainite when the normal load is 25 N. While, the SWR firstly decreases and then increases with increasing the amount of nanobainite, and the optimum wear resistance is obtained for samples with 60 vol.% nanobainite, when the applied load increases to 50 and 75 N. The improved wear resistance is attributed to the peak hardness increment resulted from the transformation of retained austenite to martensite, work hardening, along with amorphization and nanocrystallization of the worn surface. In addition, the highest toughness of the samples with 60 vol.% nanobainite is also proven to play a positive role in resisting sliding wear. EDS (energy dispersion spectrum) and XRD (X-ray diffraction) examinations reveal that the predominant failure mechanism is oxidative wear.

Dry Sliding Wear Behaviour of Fe-Based Powder Sintered Steel

2011 ◽  
Vol 415-417 ◽  
pp. 707-710
Author(s):  
Hua Chen ◽  
Hai Ying Sun
Keyword(s):  
Wear Resistance ◽  
Wear Mechanism ◽  
Sliding Wear ◽  
Hot Forging ◽  
Wear Behaviour ◽  
High Wear Resistance ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Delamination Wear ◽  
Sliding Wear Behaviour

Fe-based system powder metallurgy in the as-sintered was investigated on pin-on-rolling wear tester for their dry sliding wear behaviour. The morphology of worn surfaces and wear mechanism were analysed by SEM. Results show the hot-forging deformation quenching and tempered considerably decreased the porosity and improved wear resistance, and compare with quenching microstructure, tempered microstructure has high wear resistance and match of strength-toughness. Fe-2.0Ni-0.4Mo-0.5C-0.6Cr alloy presented best wear characteristics. SEM observations of the worn surface revealed microploughing and plastic deformation and crack were the basic dry sliding wear morphology,and oxidative wear and delamination wear are dominant wear mechanism.

scholarly journals “An Investigation of wear behavior of TiO2 nanoparticles mixed with Hybrid powder coating on MS material”

2021 ◽  
Vol 9 (12) ◽  
pp. 2350-2355
Author(s):  
Akshay Shinde
Keyword(s):  
Wear Resistance ◽  
Wear Rate ◽  
Tio2 Nanoparticles ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Wear Test ◽  
Powder Coating ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Maximum Contribution

Abstract: To improve the wear resistance of the hybrid powder coating, TiO2 nanoparticles was hot mixed to form a homogenous mixture with the powder in the range varying wt. dry sliding wear test conducted to determine the wear resistance. The experiments were design according to Taguchi L9 array to find the optimum nanoparticles content required to minimize the wear rate of the coating. ANOVA was used to determine the effect of the parameters on wear rate. It showed that reinforcement has the maximum contribution on the wear rate of the coating as compared to load and frequency. From the graph of means optimum parametric values was obtained at 2 % wt of reinforcement, 2 N load and 2 Hz frequency. The wear rate decrease with the increase in reinforcement. Keywords: Taguchi Method, Tribometer, Hybrid powder, TiO2, Wear Rate.

Effect of friction stir processing on the dry sliding wear behavior of AZ31 Mg alloy

2020 ◽  
Author(s):  
Siddramesh S. Diksangi ◽  
Sourabh Kulkarni ◽  
Vimal Edachery ◽  
Abhishek Pariyar ◽  
Santosh Kumar
Keyword(s):  
Friction Stir Processing ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Mg Alloy ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Friction Stir ◽  
Az31 Mg Alloy

scholarly journals Dry Sliding Wear Behaviour of Rheocat Al-5.7si-2cu-0.3mg Alloy

2018 ◽  
Vol 7 (3.17) ◽  
pp. 38 ◽  
Author(s):  
M A. Abdelgnei ◽  
M Z. Omar ◽  
M J. Ghazali ◽  
Mohamed A. Gebril ◽  
M N. Mohammed
Keyword(s):  
Wear Mechanism ◽  
Sliding Wear ◽  
Cast Alloy ◽  
Contact Point ◽  
Optical Microscope ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Pin On Disc ◽  
Sliding Wear Behaviour

In this study, the effect of improved microstructure of Al-5.7Si-2Cu-0.3Mg alloys by using semisolid process on hardness and dry sliding wear behaviour were investigated. The microstructures of conventional cast alloy were totally dendritic, while in rheocasting the dendritic transfer to fine globular microstructures after using cooling slope casting. Tribological tests were carried out by using a pin-on-disc apparatus in dry sliding conditions. Wear tests were at low sliding speed 1ms-1 ,applied load at 50N and three different sliding distance (i.e., 1.8Km, 5.4Km and 9Km) respectively. An optical microscope and a scanning electron microscope were used to examine the microstructure and to understand the wear mechanism on the worn surface of both samples. The results showed that, the wear resistance of rheocast alloy was improved and higher than that those produce by conventional casting. The volume loss of rheocast alloy show reduction more than 18% at 1.8Km and 10% at 9Km compared to as-cast alloy. Moderate wear regimes were appeared in both alloys, according to the range of wear rate. The friction coefficient had increased due to increase in the contact point between pin and disc materials. The dominant wear mechanism for conventional and rheocasting alloys was adhesion wear and abrasive wear respectively.  

Dry Sliding Wear of As-Cast and Thermomechanically Processed Low Chromium White Cast Iron

2013 ◽  
Vol 797 ◽  
pp. 725-730
Author(s):  
Xing Jian Gao ◽  
Qi Zhang ◽  
Dong Bin Wei ◽  
Si Hai Jiao ◽  
Zheng Yi Jiang
Keyword(s):  
Wear Resistance ◽  
Cast Iron ◽  
Thermomechanical Treatment ◽  
Sliding Wear ◽  
White Cast Iron ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Low Carbon ◽  
Wear Process

This investigation attempts to improve the wear resistance of low chromium white cast iron (LCCI) by thermomechanical treatment. The thermomechanical treatment of the brittle LCCI with crack-free was successfully carried out by bonding it with a ductile low carbon steel firstly. Afterwards the dry sliding wear behavior of as-cast (LCCI-A) and thermomechanically processed (LCCI-B) samples was studied using a pin-on-disc apparatus under different test conditions. The microstructural examination shows that the refined supercooled austenite and plenty of secondary carbides in LCCI-B replaced the original microstructure of martensite and retained austenite with network carbide in LCCI-A. This significant evolution is beneficial to form and stabilise the oxide layer on the substrate, which makes the oxidational wear rather than abrasive wear or delamination dominating the wear process so that the improvement of the wear resistance of LCCI was achieved by hot working.

Sign in / Sign up

Export Citation Format

Share Document