scholarly journals “An Investigation of wear behavior of TiO2 nanoparticles mixed with Hybrid powder coating on MS material”

2021 ◽  
Vol 9 (12) ◽  
pp. 2350-2355
Author(s):  
Akshay Shinde
Keyword(s):  
Wear Resistance ◽  
Wear Rate ◽  
Tio2 Nanoparticles ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Wear Test ◽  
Powder Coating ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Maximum Contribution

Abstract: To improve the wear resistance of the hybrid powder coating, TiO2 nanoparticles was hot mixed to form a homogenous mixture with the powder in the range varying wt. dry sliding wear test conducted to determine the wear resistance. The experiments were design according to Taguchi L9 array to find the optimum nanoparticles content required to minimize the wear rate of the coating. ANOVA was used to determine the effect of the parameters on wear rate. It showed that reinforcement has the maximum contribution on the wear rate of the coating as compared to load and frequency. From the graph of means optimum parametric values was obtained at 2 % wt of reinforcement, 2 N load and 2 Hz frequency. The wear rate decrease with the increase in reinforcement. Keywords: Taguchi Method, Tribometer, Hybrid powder, TiO2, Wear Rate.

Role of Zirconia Filler on Mechanical Properties and Dry Sliding Wear Behavior of Glass/Basalt Hybrid Fabric Reinforced Epoxy Composites

2019 ◽  
Vol 895 ◽  
pp. 200-205
Author(s):  
B.S. Kanthraju ◽  
Bheemappa Suresha ◽  
H.M. Somashekar
Keyword(s):  
Mechanical Properties ◽  
Wear Rate ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Mechanical Test ◽  
Basalt Fiber ◽  
Wear Test ◽  
Specific Wear Rate ◽  
Dry Sliding Wear ◽  
Dry Sliding

This paper presents the effect of zirconia filler on mechanical properties and dry sliding wear of bidirectional hybrid (glass and basalt fiber) fabric reinforced epoxy (G-B/E) composites. Fabrication was done by hand layup method followed by compression molding. The effect of zirconia filler loading on mechanical characteristics like hardness, tensile and flexure of fabricated G-B/E composites were determined according to ASTM standards. Also, wear behavior under dry sliding condition was performed using pin-on-disc machine for different applied normal loads/sliding distance. Experimental results reveal that incorporation of zirconia filler improves the mechanical properties. Further, the wear test results indicated addition of zirconia into G-B/E hybrid fiber composites plays important role on specific wear rate under the tribo-conditions selected for the study. Further, inclusion of zirconia into G-B/E composites shows improved wear resistance and addition of 6 wt. % of zirconia exhibits least specific wear rate compared to other hybrid G-B/E composites. In addition, Scanning electron microscope images of selected mechanical test fractured coupons also have been discussed.

Study of Microstructure and Wear Behavior of T6 Heat Treated as Cast Al-25Mg2Si-2Cu Alloy

2015 ◽  
Vol 830-831 ◽  
pp. 358-361 ◽  
Author(s):  
D.G. Sondur ◽  
D.M. Goudar ◽  
D.G. Mallapur ◽  
G.B. Rudrakshi
Keyword(s):  
Wear Resistance ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Cast Alloy ◽  
Wear Test ◽  
Wear Behaviour ◽  
High Wear Resistance ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Heat Treated

In the present investigation, microstructural characteristics and dry sliding wear behaviour of T6 heat treated conventionally cast Al-25Mg2Si-2Cu alloy have been discussed. The as cast alloy was subjected to solutionizing at 500°C for 5h and isothermal aging treatment at 190°C for different aging times. The micro structural characterization was studied using Scanning Electron Microscope with EDS analysis. The microstructure of as cast alloy consists of intermetallics of coarse block like sharp edged β-(Mg2Si), θ-(Al2Cu) and Q-(Al-Mg-Cu-Si) in the form of Chinese scripts and needles distributed randomly in the Al-matrix. The microstructure of heat treated alloy shows spheroidization of β phase and fine precipitation of θ-(Al2Cu) and Q phases. The dry sliding wear test was carried out using pin-on-disc machine. Age hardened alloy exhibits high wear resistance and minimum coefficient of friction over the entire range of applied loads and sliding velocities. Furthermore, high wear resistance was observed in the under aged condition compared to over ageing conditions.

Dry Sliding Wear Behavior of 2218 Al-Alloy-Al2O3(TiO2) Hybrid Composites

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Vineet Tirth
Keyword(s):  
Wear Rate ◽  
Sliding Wear ◽  
Hybrid Composites ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Aged Alloy ◽  
Dry Sliding ◽  
Al Alloy ◽  
Mathematical Relationship ◽  
Sliding Distance

AA2218–Al2O3(TiO2) composites are synthesized by stirring 2, 5, and 7 wt % of 1:2 mixture of Al2O3:TiO2 powders in molten AA2218 alloy. T61 heat-treated composites characterized for microstructure and hardness. Dry sliding wear tests conducted on pin-on-disk setup at available loads 4.91–13.24 N, sliding speed of 1.26 m/s up to sliding distance of 3770 m. Stir cast AA2218 alloy (unreinforced, 0 wt % composite) wears quickly by adhesion, following Archard's law. Aged alloy exhibits lesser wear rate than unaged (solutionized). Mathematical relationship between wear rate and load proposed for solutionized and peak aged alloy. Volume loss in wear increases linearly with sliding distance but drops with the increase in particle wt % at a given load, attributed to the increase in hardness due to matrix reinforcement. Minimum wear rate is recorded in 5 wt % composite due to increased particles retention, lesser porosity, and uniform particle distribution. In composites, wear phenomenon is complex, combination of adhesive and abrasive wear which includes the effect of shear rate, due to sliding action in composite, and abrasive effect (three body wear) of particles. General mathematical relationship for wear rate of T61 aged composite as a function of particle wt % load is suggested. Fe content on worn surface increases with the increase in particle content and counterface temperature increases with the increase in load. Coefficient of friction decreases with particle addition but increases in 7 wt % composite due to change in microstructure.

Dry Sliding Wear Behavior of Hot Pressed Fe-28Al and Fe-28Al-10Ti Alloys

2011 ◽  
Vol 306-307 ◽  
pp. 425-428
Author(s):  
Jing Li ◽  
Xiao Hong Fan ◽  
De Ming Sun
Keyword(s):  
Plastic Deformation ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Wear Test ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Long Distance ◽  
Wear Performance ◽  
Testing Conditions ◽  
Worn Surface

Fe-28Al and Fe-28Al-10Ti alloys were prepared by mechanical alloying and hot pressing. The phases and dry sliding wear behavior were studied. The results show that Fe-28Al bulk materials are mainly characterized by the low ordered B2 Fe3Al structure with some dispersed Al2O3 particles. Fe-28Al-10Ti exhibits more excellent wear resistance than Fe-28Al, especially after long distance sliding wear test. There are obvious differences in wear mechanisms of Fe-28Al and Fe-28Al-10Ti alloys under different testing conditions. Under the load of 100N, there is plastic deformation on the worn surface of Fe-28Al. The main wear performance of Fe-28Al-10Ti is particle abrasion, the characteristics of which are micro cutting and micro furrows, but micro-crack and layer splitting begin to form on the surface of Fe-28Al. Under the load of 200N, serious plastic deformation and work-hardening lead to rapid crack propagation and eventually the fatigue fracture of Fe-28Al. Plastic deformation is the main wear mechanism of Fe-28Al-10Ti under the load of 200N, which are characterized by micro-crack and small splitting from the worn surface.

scholarly journals Effect of Necklace-Type Distribution of SiC Particles on Dry Sliding Wear Behavior of As-Cast AZ91D/SiCp Composites

Crystals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 296 ◽  
Author(s):  
Chao Sun ◽  
Nannan Lu ◽  
Huan Liu ◽  
Xiaojun Wang ◽  
Xiaoshi Hu ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Interface Bonding ◽  
Type Distribution ◽  
Wear Rates ◽  
Sic Particles ◽  
The Matrix

In this study, the dry sliding wear behaviors of SiC particle reinforced AZ91D matrix composites fabricated by stirring casting method were systematically investigated. The SiC particles in as-cast composites exhibited typical necklace-type distribution, which caused the weak interface bonding between SiC particles and matrix in particle-segregated zones. During dry sliding at higher applied loads, SiC particles were easy to debond from the matrix, which accelerated the wear rates of the composites. While at the lower load of 10 N, the presence of SiC particles improved the wear resistance. Moreover, the necklace-type distribution became more evident with the decrease of particle sizes and the increase of SiC volume fractions. Larger particles had better interface bonding with the matrix, which could delay the transition of wear mechanism from oxidation to delamination. Therefore, composites reinforced by larger SiC particles exhibited higher wear resistance. Similarly, owing to more weak interfaces in the composites with high content of SiC particles, more severe delamination occurred and the wear resistance of the composites was impaired.

Microstructure and Wear Properties of In Situ TiC-Cr7C3/Fe Surface Composite

2011 ◽  
Vol 415-417 ◽  
pp. 170-173
Author(s):  
Jing Wang ◽  
Si Jing Fu ◽  
Yi Chao Ding ◽  
Yi San Wang
Keyword(s):  
Sliding Wear ◽  
Wear Behavior ◽  
Wear Test ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Test Machine ◽  
Wear Properties ◽  
Surface Composite ◽  
The Matrix

A wear resistant TiC-Cr7C3/Fe surface composite was produced by cast technique and in-situ synthesis technique. The microstructure and dry-sliding wear behavior of the surface composite was investigated using scanning electron microscope(SEM), X-ray diffraction(XRD) and MM-200 wear test machine. The results show that the surface composite consists of TiC and Cr7C3as the reinforcing phase, α-Fe and γ-Fe as the matrix. The surface composite has excellent wear-resistance under dry-sliding wear test condition with heavy loads.

scholarly journals Effect of Nanobainite Content on the Dry Sliding Wear Behavior of an Al-Alloyed High Carbon Steel with Nanobainitic Microstructure

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1618 ◽  
Author(s):  
Zhaohuan Song ◽  
Songhao Zhao ◽  
Tao Jiang ◽  
Junjie Sun ◽  
Yingjun Wang ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Carbon Steel ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Normal Load ◽  
High Carbon Steel ◽  
Peak Hardness ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
High Carbon

In this work, a multiphase microstructure consisting of nanobainte, martensite, undissolved spherical carbide, and retained blocky austenite has been prepared in an Al-alloyed high carbon steel. The effect of the amount of nanobainite on the dry sliding wear behavior of the steel is studied using a pin-on-disc tester with loads ranging from 25–75 N. The results show that, there is no significant differences in specific wear rate (SWR) for samples with various amounts of nanobainite when the normal load is 25 N. While, the SWR firstly decreases and then increases with increasing the amount of nanobainite, and the optimum wear resistance is obtained for samples with 60 vol.% nanobainite, when the applied load increases to 50 and 75 N. The improved wear resistance is attributed to the peak hardness increment resulted from the transformation of retained austenite to martensite, work hardening, along with amorphization and nanocrystallization of the worn surface. In addition, the highest toughness of the samples with 60 vol.% nanobainite is also proven to play a positive role in resisting sliding wear. EDS (energy dispersion spectrum) and XRD (X-ray diffraction) examinations reveal that the predominant failure mechanism is oxidative wear.

scholarly journals Dry Sliding Wear Behavior of B4C and Graphite Particulates Reinforced A356 Alloy Composites

2018 ◽  
Vol 7 (2.23) ◽  
pp. 446
Author(s):  
Pankaj R Jadhav ◽  
B R Sridhar ◽  
Madeva Nagaral ◽  
Jayasheel I Harti ◽  
V Auradi
Keyword(s):  
Sliding Wear ◽  
Hybrid Composites ◽  
Wear Behavior ◽  
A356 Alloy ◽  
Wear Test ◽  
The Other ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Mechanical Assembly ◽  
Wear Protection

The present works manages readiness of the composites by mix stirring method. A356 amalgam 4 wt. % of B4C and A356-4 wt. % of Graphite and A356-4% B4C-4% Graphite hybrid composites were readied. To enhance the wetting and uniform conveyance of the particles, fortifications were preheated to a temperature of 500 Degree Celsius. The arranged MMCs are subjected to examining SEM instrument which affirms the homogenous uniform appropriation of smaller scale B4C and Graphite particles in the lattice combination without agglomeration. The wear protection of arranged composites was examined by performing dry sliding wear test utilizing DUCOM made stick on plate mechanical assembly. The tests were directed at a consistent heap of 3kg and sliding separation of 4000m over a speed of 100, 200 and 300 rpm. So also the other arrangement of investigations were led at consistent sped of 300 rpm and sliding separation of 4000m and with changing heap of 1kg, 2kg, and 3kg. The outcomes demonstrated that the wear protections of the composites were improved than the lattice material.   

Garnet and Al-flyash composite under dry sliding conditions

2017 ◽  
Vol 52 (17) ◽  
pp. 2281-2288 ◽  
Author(s):  
S Sivakumar ◽  
S Senthil Kumaran ◽  
M Uthayakumar ◽  
A Daniel Das
Keyword(s):  
Genetic Algorithm ◽  
Wear Rate ◽  
Process Parameters ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Testing Machine ◽  
Wear Testing ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Dry Sliding

The dry sliding wear behaviour of LM 24 aluminum alloy composites reinforced with garnet particles was evaluated. Stir casting technique was used to fabricate the composites. A pin-on-disc wear-testing machine was used to evaluate the wear rate, in which an EN 24 steel disc was used as the counterface. Results indicated that the wear rates of the composites were lower than that of the matrix alloy and further decreased with the increase in garnet content. However, in both unreinforced and reinforced composites, the wear rate increased with the increase in load and the sliding speed. Increase in the applied load increased the wear severity by changing the wear mechanism from abrasion to particle cracking-induced delamination wear. It was found that with the increase in garnet content, the wear resistance increased monotonically. The observations have been explained using scanning electron microscopy analysis of the worn surfaces and the subsurface of the composites. In this work, the most influencing input and output parameters have been performed and the process parameters have been prioritized using genetic algorithm. Genetic algorithm is used to optimize the most influencing input as well as output process parameters. The practical significance of applying genetic algorithm to dry sliding wear behavior process has been validated by means of computing the deviation between predicted and experimentally obtained wear behavior of metal matrix composite.

Effect of Fine TiC Particle Reinforcement on the Dry Sliding Wear Behavior of In Situ Synthesized ZA27 Alloy

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Roshita David ◽  
Rupa Dasgupta ◽  
B. K. Prasad
Keyword(s):  
Wear Rate ◽  
Coefficient Of Friction ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Base Alloy ◽  
Dry Sliding Wear ◽  
Wear Volume ◽  
Dry Sliding ◽  
Material Loss

The in situ method of making zinc-aluminum composites wherein TiC has been introduced has been investigated in the present paper for its microstructural, physical, and dry sliding wear behavior and compared with the base alloy. In the present study, ZA-27 alloy reinforced with 5 and 10 vol % TiC was taken into consideration. The results indicate that the wear rate and coefficient of friction of composites were lower than that of base alloy. The material loss in terms of both wear volume loss and wear rate increases with increase in load and sliding distance, respectively, while coefficient of friction follows a reverse trend with increase in load. Better performance was obtained for 5% TiC reinforcement than with 10% probably due to agglomeration of particles resulting in nonuniform dispersion. Worn surfaces were analyzed by scanning electron microscopy (SEM) analysis.

Sign in / Sign up

Export Citation Format

Share Document