scholarly journals Multifactor Evaluation of Multiple Service Support and Optimization of Working Resistance of New Support Based on Dynamic Pressure

2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Fulian He ◽  
Liang Li ◽  
Wenrui He ◽  
Xiaobin Li ◽  
Kai Lv ◽  
...  
Keyword(s):  
Coal Seam ◽  
Loss Rate ◽  
Dynamic Pressure ◽  
New Method ◽  
Scientific Evaluation ◽  
Service Support ◽  
Coal Cutting ◽  
Working Face ◽  
Periodic Pressure ◽  
Working Resistance

The scientific and feasible method is extremely important for the evaluation of whether the support of coal mines needs to be scrapped, but it has not been formed. If the support cannot be continued to use, the determined reasonable working resistance of the support before the primary mining of coal seam should be optimized. Based on the field measurement and theoretical analysis, the concept of the actual rated working resistance of the support is proposed and analyzed accurately; the total amount of roof subsidence of circulating multiple coal cutting cycles during periodic pressure is calculated; the support performance is evaluated by multifactors; a new method for determining the reasonable working resistance of the support based on dynamic pressure is proposed. The study found that the safety valve of support is opened in advance and the resistance loss rate is large; the total amount of roof subsidence during periodic pressure is high; FAHP + EWM evaluation score of support system performance is 63.31 points. The scientific evaluation of multifactors showed that the support has reached service life, and as a result, the new 105 working faces required replacement with new support. The reasonable working resistance of the support in the 3-1 coal seam is optimized according to the new method based on dynamic pressure. This study can greatly improve the safety of roof control in the working face.

The Adaptation Analysis of the Fully Mechanized Coal Mining Face of Huopu Mine’s Third Soft Coal Seam

2014 ◽  
Vol 1049-1050 ◽  
pp. 335-338 ◽  
Author(s):  
Fa Quan Liu ◽  
Xue Wen Geng ◽  
Yong Che ◽  
Xiang Cui
Keyword(s):  
Coal Seam ◽  
Coal Mining ◽  
Geological Condition ◽  
Soft Coal ◽  
Working Face ◽  
Mining Face ◽  
Soft Coal Seam ◽  
Working Resistance

To get the maximum coal in front of the working face of the 17# coal seam, we installed a longer beam which is 1.2m in length in the leading end of the original working face supports ZF3000/17/28, and know that working face supports’ setting load and working resistance are lower .We changed the original supports with shield supports ZY3800/15/33 that are adaptable in the geological condition and got the favorable affection.

Study on the Structure Characteristics and Ground Pressure Behavior of Overlying Strata with Shallow Buried Coal Seam

2011 ◽  
Vol 255-260 ◽  
pp. 3780-3785 ◽  
Author(s):  
Lei Yu ◽  
Zhi Zhong Fan ◽  
Gang Xu
Keyword(s):  
Coal Seam ◽  
Ground Subsidence ◽  
Mine Pressure ◽  
Structure Characteristics ◽  
Pressure Behavior ◽  
Ground Pressure ◽  
Working Face ◽  
Periodic Pressure ◽  
Seam Mining ◽  
Overlying Strata

The mine pressure behavior characters of shallow buried coal seam differed from both shallow seam mining and general depth seam. Mine pressure observation and numerical analysis were applied to research mine pressure behavior laws in fully mechanized face of shallow buried coal seam with thick bedrock and thin alluvium. It showed that the ground subsidence level phenomenon did not appear obviously although with obvious dynamic loading of fully mechanized face during the pressure period. The appearance was due to non-synchronized fracture from two key layers in the overlying rock layers and their interaction, which leaded to roof breaking initially and caving rocks with the form of an arch. Due to the periodic breaking and caving characteristics appearing as fully cut-down and arch alternately, the periodic pressure of shallow buried coal seam face showed as different size. The conclusion could be a reference for similar working face control.

Determination Method of the Supporting Intensity of Fully-Mechanized Face in Deeply Inclined Medium-Thickness Seam

2014 ◽  
Vol 522-524 ◽  
pp. 1386-1389
Author(s):  
Zhong Ping Guo ◽  
Hui Qiang Duan ◽  
Fan Feng ◽  
Gui Yin Zhang
Keyword(s):  
Coal Seam ◽  
Theoretical Basis ◽  
Surrounding Rock ◽  
Medium Thickness ◽  
Working Face ◽  
Displacement Thickness ◽  
Face Length ◽  
Working Resistance ◽  
Theory Calculation ◽  
The Relationship

According to the occurrence conditions of deeply inclined coal seam of 81206 working face in Yanya coal mine, methods including transmission rock theory calculation and numerical calculation based on the relationship between supports and surrounding rock are used to calculate and analyze. The proper working resistance of support is 5979.2kN and the supporting intensity is 0.8~0.95MPa. The regression equation associated with roof subsidence displacement , thickness of the coal seam, working face length and supporting intensity is accomplished, which provides theoretical basis for the support selection.

scholarly journals Ground Stress Distribution and Dynamic Pressure Development of Shallow Buried Coal Seam Underlying Adjacent Room Gobs

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Ming Zhang ◽  
Chen Cao ◽  
Bingjie Huo
Keyword(s):  
Stress Distribution ◽  
Theoretical Analysis ◽  
Coal Seam ◽  
Dynamic Pressure ◽  
Coal Pillar ◽  
Horizontal Stress ◽  
Working Face ◽  
Ground Stress ◽  
Stress Environment ◽  
Coal Pillars

The condition of the coal pillars remained in the room-and-pillar gobs is complicated. The stresses loaded on the pillar floor may be transmitted and overlapped. It changes the stress environment of the lower coal seam roof, leading abnormal periodic weighting. In the procedure of coal seam 3−1 mining in the Huoluowan Coal Mine, the ground stress is high while the working face passing through the room pillars of overlying coal seam 2−2, leading to hydraulic shield being broken. In this paper, theoretical analysis, numerical calculation, and similar material simulation were used to analyse the stress environment of lower seam and the effect of coal pillars remained in close-distanced upper seam. The stress transfer model was established for the room pillars of coal seam 2−2, and the stress distribution of underlying strata was obtained based on theoretical analysis. The joint action of dynamic pressure of high stress-coal pillar with movement of overlying rock strata in the working face 3−1 under the coal pillar was revealed. The results showed that the horizontal stress and vertical stress under the large coal pillar of the room gob in coal seam 2−2 were high, being from 9.7 to 15.3 MPa. The influencing depth of vertical stress ranged from 42 m to 58 m. The influencing depth of horizontal stress ranged from 10 to 23 m. The influencing range of the shear stress was from 25 to 50 m. When the working face 3−1 was mined below the coal pillar of 20 m or 50 m, abutment pressure was relatively high. The stress concentration coefficient reached 4.44–5.00. The dynamic pressure of the working face was induced by the stress overlying of the upper and lower coal seams, instability of the inverted trapezoid rock pillar above the coal pillar, and collapsing movement of the roof. The studying results were beneficial for guiding the safety mining of the coal seam 3−1 in the Huoluowan Coal Mine.

Characters Evaluation of Ground Pressure in Fully Mechanized Top Coal Caving Face in Soft Coal Seams

2011 ◽  
Vol 255-260 ◽  
pp. 3735-3739
Author(s):  
Wei Dong Pan ◽  
Xiao Hua Wu ◽  
Yang Li
Keyword(s):  
Coal Seam ◽  
Mining Area ◽  
Base Point ◽  
Coal Seams ◽  
Distribution Law ◽  
Soft Coal ◽  
Ground Pressure ◽  
Working Face ◽  
Working Resistance ◽  
Hydraulic Supports

Based on the big thickness, low stiffiness and other characters of No. 8 coal seam in Huaibei mining area, the moving laws of top coal seam and roof, and distribution law of ground pressure were studied under the fully mechanized top coal caving. The research methods included working resistance observation of hydraulic supports in working face, deformation observation of stope roadways and deeper base point observation in roof and top coal. The results show that, in the thick and soft coal seams, the influence coverage of mining ground pressure in fully mechanized top coal caving face is much wider than that in the working face with general mining technology, but the intensity of pressure is much lower.

Analyses of Actual Measurement and Numerical Simulation on Gently Inclined Thin Seam

2011 ◽  
Vol 361-363 ◽  
pp. 130-134
Author(s):  
Jian Xin Tang ◽  
Le Le Sun ◽  
Yue Hua Deng ◽  
Hua Hui Jin
Keyword(s):  
Numerical Simulation ◽  
Dynamic Pressure ◽  
Pressure Coefficient ◽  
River Mouth ◽  
Main Roof ◽  
Simulation Method ◽  
Actual Measurement ◽  
Working Face ◽  
Thin Seam ◽  
Working Resistance

Based on the numerical simulation method and actual measurement analyses, characteristics of working face mineral pressure of the River Mouth Mine has been analyzed and this paper has obtained the following results: First weighting step of the main roof is 23.2 m, the average dynamic pressure coefficient is 1.54~1.74, mine strata behaviors is fiercer; hydraulic prop’s average working resistance is 45.72 KN of each, which indicates hydraulic prop’s working resistance has larger surplus coefficient, some measures should be taken to increase utilization ratio; advanced support length of return airway and mechanical roadway should reach to 30 m, the method and results can be used to improve support pattern of working face and guide safety production.

scholarly journals Stability of a Roadway below a Coal Seam under Dynamic Pressure: A Case Study of the 11123 Floor Gas Drainage Roadway of a Mine in Huainan, China

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Pingsong Zhang ◽  
Yuanchao Ou ◽  
Chang Liu ◽  
Binyang Sun ◽  
Chong Xu
Keyword(s):  
Rock Mass ◽  
Coal Seam ◽  
Dynamic Pressure ◽  
Time Domain Reflectometry ◽  
Surrounding Rock ◽  
Monitoring Method ◽  
Gas Drainage ◽  
Gas Outburst ◽  
Working Face ◽  
Seam Mining

Coal and gas outburst is an important risk faced by coal seam mining in the Huainan region of China. In order to control gas outburst, the gas is predrained by digging a floor gas drainage roadway. To study deformation due to dynamic pressure, the failure characteristics of the floor, and their effect on the stability of the floor gas drainage roadway, a comprehensive monitoring method combining Brillouin optical time-domain reflectometry- (BOTDR-) distributed fiber optics and self-potential exploration was adopted. Dynamic data monitoring of the rock strata between the 11123 working face floor and the floor gas drainage roadway of a mine in Huainan was carried out. The field data obtained showed that, when stabilized by rock bolts and other fixed components in the surrounding rock mass of the floor gas drainage roadway, under the influence of mining, the area of concentrated stress appeared at a depth of 20.7 m, when cracks eventually formed, but the overall structural stability of the surrounding rock mass remained good. The stress distribution and crack evolution of the bottom plate under the influence of dynamic pressure showed spatiotemporal characteristics. Of these, the effect of the lead support stress was 107.48 m, and the range of effect of the hysteresis stress was 34.42 m. When the working face mining position arrives and is far from the monitoring station, the failure depth of floor rock stratum shows the following rule: unchanged in the early stage, deepened continuously in the middle stage, and finally remained stable. It takes about eight days for the dynamic adjustment of this process to finally stabilize. The results of this study can provide guidance for devising suitable procedures for carrying out intelligent green safety mining and for warning about the hazards of roadway damage.

scholarly journals Mine Strata Pressure Characteristics and Mechanisms in Gob-Side Entry Retention by Roof Cutting under Medium-Thick Coal Seam and Compound Roof Conditions

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2539 ◽  
Author(s):  
Xingen Ma ◽  
Manchao He ◽  
Jiong Wang ◽  
Yubing Gao ◽  
Daoyong Zhu ◽  
...  
Keyword(s):  
Theoretical Analysis ◽  
Coal Seam ◽  
Dynamic Pressure ◽  
Beam Theory ◽  
Main Roof ◽  
The Other ◽  
Thick Coal Seam ◽  
Plate Length ◽  
Working Face ◽  
Mining Face

Coal is among the most important energy sources, and gob-side entry retention by roof cutting (GERRC) is an innovative non-pillar mining technique that can effectively increase coal recovery rates and avoid coal wastage. To investigate the characteristics of mine strata pressure using the GERRC technique, a field case study under conditions involving a medium-thick coal seam and a compound roof was performed, and the mine strata behavior mechanisms were studied by theoretical analysis. Field monitoring shows that the distributions of the weighting step and strength along the longwall working face are asymmetrical. The periodic weighting length on the entry retaining side is longer than that on the other sides of the longwall working face, and the average increase is appropriately 4 m. Compared to the other sides of the longwall, on the entry retaining side, the periodic weighting strength is weaker, the average pressure is reduced by 2.1 MPa, and the peak pressure is reduced by 10.2 MPa. The lateral distance affected by roof cutting along the longwall is approximately 29.75 m, and the closer to the cutting slit, the more significant the roof cutting effect is. The retained entry becomes stable when it is more than 230 m behind the mining face, and the final cross section of the retained entry can meet the reuse demand of the next mining face. Theoretical analysis shows that the roof pressure mechanism in GERRC can be explained using cantilever beam theory. Within the area affected by roof cutting, the thickness of the immediate roof increases, and the suspension plate length of the roof immediately behind the longwall decreases. Then, the gangue pile in the goaf behind the longwall formed by the immediate roof’s collapse and expansion can support the main roof and other overlying strata much better. Therefore, the rotational breaking angle of the main roof is smaller, the periodic weighting step strength increases, and the periodic weighting decreases. According to the structural state of the surrounding rocks during the entire entry retaining process, the retained entry can be divided into coal support, dynamic pressure and stable entry areas.

scholarly journals Stress and deformation analysis of gob-side pre-backfill driving procedure of longwall mining: a case study

2021 ◽  
Author(s):  
Rui Wu ◽  
Penghui Zhang ◽  
Pinnaduwa H. S. W. Kulatilake ◽  
Hao Luo ◽  
Qingyuan He
Keyword(s):  
Rock Mass ◽  
Stress Distribution ◽  
Coal Seam ◽  
Abutment Pressure ◽  
Longwall Mining ◽  
Vertical Stress ◽  
Floor Level ◽  
Working Face ◽  
Floor Heave ◽  
Stress And Deformation

AbstractAt present, non-pillar entry protection in longwall mining is mainly achieved through either the gob-side entry retaining (GER) procedure or the gob-side entry driving (GED) procedure. The GER procedure leads to difficulties in maintaining the roadway in mining both the previous and current panels. A narrow coal pillar about 5–7 m must be left in the GED procedure; therefore, it causes permanent loss of some coal. The gob-side pre-backfill driving (GPD) procedure effectively removes the wasting of coal resources that exists in the GED procedure and finds an alternative way to handle the roadway maintenance problem that exists in the GER procedure. The FLAC3D software was used to numerically investigate the stress and deformation distributions and failure of the rock mass surrounding the previous and current panel roadways during each stage of the GPD procedure which requires "twice excavation and mining". The results show that the stress distribution is slightly asymmetric around the previous panel roadway after the “primary excavation”. The stronger and stiffer backfill compared to the coal turned out to be the main bearing body of the previous panel roadway during the "primary mining". The highest vertical stresses of 32.6 and 23.1 MPa, compared to the in-situ stress of 10.5 MPa, appeared in the backfill wall and coal seam, respectively. After the "primary mining", the peak vertical stress under the coal seam at the floor level was slightly higher (18.1 MPa) than that under the backfill (17.8 MPa). After the "secondary excavation", the peak vertical stress under the coal seam at the floor level was slightly lower (18.7 MPa) than that under the backfill (19.8 MPa); the maximum floor heave and maximum roof sag of the current panel roadway were 252.9 and 322.1 mm, respectively. During the "secondary mining", the stress distribution in the rock mass surrounding the current panel roadway was mainly affected by the superposition of the front abutment pressure from the current panel and the side abutment pressure from the previous panel. The floor heave of the current panel roadway reached a maximum of 321.8 mm at 5 m ahead of the working face; the roof sag increased to 828.4 mm at the working face. The peak abutment pressure appeared alternately in the backfill and the coal seam during the whole procedure of "twice excavation and mining" of the GPD procedure. The backfill provided strong bearing capacity during all stages of the GPD procedure and exhibited reliable support for the roadway. The results provide scientific insight for engineering practice of the GPD procedure.

Sign in / Sign up

Export Citation Format

Share Document