scholarly journals Development of a Frequency-Adjustable Tuned Mass Damper (FATMD) for Structural Vibration Control

2020 ◽  
Vol 2020 ◽  
pp. 1-16
Author(s):  
Huaguo Gao ◽  
Congbao Wang ◽  
Chen Huang ◽  
Wenlong Shi ◽  
Linsheng Huo
Keyword(s):  
Damping Ratio ◽  
Tuned Mass Damper ◽  
Vertical Vibration ◽  
Structural Vibration ◽  
Kinematic Equation ◽  
Pedestrian Bridge ◽  
Long Span ◽  
Mass Damper ◽  
Excitation Frequencies ◽  
Simple Assembly

The tuned mass damper (TMD) can be applied to suppress earthquake, wind, and pedestrian- and machine-induced vibration in factory buildings or large span structures. However, the traditional TMD with a fixed frequency will not be able to perform effectively against the frequency variations in multiple hazards. This paper proposed a frequency-adjustable tuned mass damper (FATMD) to solve this limitation of current TMD. The FATMD presented in this paper is composed of a simple assembly consisting of a supported beam with a mass, in which the frequency of the FATMD is changed by adjusting the span of the beam. The kinematic equation of a single degree of freedom (SDOF) structure installed with an FATMD is established to analyze the effect of the damping ratio, mass ratio, and stiffness on the vibration damping. The fundamental frequency of the FATMD at different spans is verified by simulation and experiments. Forced vibration experiments with different excitation frequencies are also conducted to verify the performance of the FATMD. The results show that the proposed FATMD can effectively suppress the vertical vibration of structures at different excitation frequencies, including frequencies at a range higher than what a traditional TMD may not be able to suppress. Additionally, the proposed FATMD is applied to a long-span pedestrian bridge which vibrates frequently due to the walking of pedestrians, the running of escalators, and earthquakes. The numerical results indicate that the FATMD can effectively reduce the vertical vibration of the pedestrian bridge under the excitations of pedestrians, escalators, and earthquakes.

scholarly journals Parametric Study of Tuned Mass Dampers for Long Span Transmission Tower-Line System under Wind Loads

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Li Tian ◽  
Yujie Zeng
Keyword(s):  
Frequency Ratio ◽  
Damping Ratio ◽  
Vibration Reduction ◽  
Tuned Mass Damper ◽  
Reduction Ratio ◽  
Transmission Tower ◽  
Tuned Mass Dampers ◽  
Line System ◽  
Long Span ◽  
Mass Damper

A parametric study of tuned mass dampers for a long span transmission tower-line system under wind loads is done in this paper. A three-dimensional finite element model of transmission tower-line system is established by SAP2000 software to numerically verify the effectiveness of the tuned mass damper device. The wind load time history is simulated based on Kaimal spectrum by the harmony superposition method. The equations of motion of a system with tuned mass damper under wind load excitation are proposed, and the schematic of tuned mass damper is introduced. The effects of mass ratio, frequency ratio, damping ratio, the change of the sag of transmission line, and the robustness of TMD are investigated, respectively. Results show that(1)the change of mass ratio has a greater effect on the vibration reduction ratio than those of frequency ratio and damping ratio, and the best vibration reduction ratio of TMD is not the frequency ratio of 1;(2)the sag-span ratio has an insignificant effect on the vibration reduction ratio of transmission tower when the change of sag-span ratio is not large; and(3)the effect of ice should be considered when the robustness study of TMD is carried out.

scholarly journals Exact Solutions for a Novel H2 Optimal Design of Electromagnetic Tuned Mass Damper

2021 ◽  
Author(s):  
Ge Li ◽  
Qibo Mao ◽  
Yifan Luo ◽  
Yong Wang ◽  
Lei Liu
Keyword(s):  
Vibration Control ◽  
Optimization Design ◽  
Damping Ratio ◽  
Tuned Mass Damper ◽  
Parameters Optimization ◽  
Structural Vibration ◽  
Control Effect ◽  
Mass Damper ◽  
Two Parameters ◽  
H2 Optimization

To realize structural vibration control,a two parameters H2 optimization design was proposed to optimize the tuning ratio and damping ratio for electromagnetic tuned mass damper (EMTMD). The control effect of this two parameters optimization design is better than that of classical tuned mass damper (TMD).For this two parameters optimization,the most important thing is that the inductance of the coil can be set very small and the external load resistance can be positive ,which can avoid the use of complex negative impedance circuit. If Ref.[6] were designed according to the H2 optimization of two parameters, the EMTMD can be used for multi-modal vibration control of structures without connecting negative inductance and negative resistance spontaneously.

scholarly journals Vibration suppression of structures using tuned mass damper technology: A state-of-the-art review

2021 ◽  
pp. 107754632098430
Author(s):  
Fan Yang ◽  
Ramin Sedaghati ◽  
Ebrahim Esmailzadeh
Keyword(s):  
Mathematical Modeling ◽  
Vibration Suppression ◽  
State Of The Art ◽  
Optimization Procedure ◽  
Tuned Mass Damper ◽  
Structural Vibration ◽  
Practical Realization ◽  
Reliable Operation ◽  
Mass Damper ◽  
Structural Vibration Suppression

To date, considerable attention has been paid to the development of structural vibration suppression techniques. Among all vibration suppression devices and techniques, the tuned mass damper is one of the most promising technologies due to its mechanical simplicity, cost-effectiveness, and reliable operation. In this article, a critical review of the structural vibration suppression using tuned mass damper technology will be presented mainly focused on the following four categories: (1) tuned mass damper technology and its modifications, (2) tuned mass damper technology in discrete and continuous structures (mathematical modeling), (3) optimization procedure to obtain the optimally designed tuned mass damper system, and (4) active tuned mass damper and semi-active tuned mass damper with the practical realization of the tuned mass damper technologies.

Determination of optimal parameters of the tuned mass damper to reduce the torsional vibration of the shaft by using the principle of minimum kinetic energy

2018 ◽  
Vol 233 (2) ◽  
pp. 327-335 ◽  
Author(s):  
Duy-Chinh Nguyen
Keyword(s):  
Kinetic Energy ◽  
Torsional Vibration ◽  
Damping Ratio ◽  
Vibration Reduction ◽  
Tuned Mass Damper ◽  
Optimal Parameters ◽  
Lagrangian Equations ◽  
Tuning Ratio ◽  
Mass Damper

In this paper, an analytical method is presented to determine the optimal parameters of the symmetric tuned mass damper, such as the ratio between natural frequency of tuned mass damper and shaft (tuning ratio) and the ratio of the viscous coefficient of tuned mass damper (damping ratio). The optimal parameters of tuned mass damper are applied to reduce the torsional vibration of the shaft based on consideration of the vibration duration and stability criterion. The dynamic equations of the shaft are provided via Lagrangian equations, and the optimal parameters of tuned mass damper are derived by using the principle of minimum kinetic energy. Analytical and numerical examples are implemented to verify the reliability of the proposed method. The analytical and numerical results indicate that the optimal parameters of tuned mass damper have significant effects in the torsional vibration reduction of the shaft.

A parametric study on reliability-based tuned-mass damper design against bridge flutter

2015 ◽  
Vol 23 (9) ◽  
pp. 1518-1534 ◽  
Author(s):  
Filippo Ubertini ◽  
Gabriele Comanducci ◽  
Simon Laflamme
Keyword(s):  
Design Procedure ◽  
Tuned Mass Damper ◽  
Computationally Efficient ◽  
Long Span Bridges ◽  
Long Span ◽  
Mass Damper ◽  
Supplemental Damping ◽  
Damper Design ◽  
Reducing Costs ◽  
First Order Method

We present a probabilistic methodology for designing tuned mass dampers for flutter suppression in long-span bridges. The procedure is computationally efficient and computes the probability of flutter occurrence based on a modified first-order method of reliability analysis, a reduced-order representation of the structure and a time domain formulation of aeroelastic loads. Results of a parametric investigation show that the proposed methodology is preferable to a deterministic design procedure, which relies on nominal values of mechanical and aerodynamic parameters and does not guarantee the maximum safety. Furthermore, the reliability-based approach can be effectively used in the design of multiple tuned mass damper configurations by enhancing robustness against frequency mistuning and by reducing costs associated with supplemental damping for a given safety performance level.

Robust multi-objective optimization design of active tuned mass damper system to mitigate the vibrations of a high-rise building

2014 ◽  
Vol 229 (1) ◽  
pp. 26-43 ◽  
Author(s):  
S Pourzeynali ◽  
S Salimi
Keyword(s):  
Damping Ratio ◽  
Tuned Mass Damper ◽  
Robust Design Optimization ◽  
Design Parameters ◽  
Control Force ◽  
Multi Objective ◽  
High Rise ◽  
High Rise Building ◽  
Mass Damper ◽  
Damper Design

In engineering applications, many control devices have been developed to reduce the vibrations of structures. Active tuned mass damper system is one of these devices, which is a combination of a passive tuned mass damper system and an actuator to produce a control force. The main objective of this paper is to present a practical procedure for both deterministic and probabilistic design of the active tuned mass damper control system using multi-objective genetic algorithms to mitigate high-rise building responses. For this purpose, extensive numerical analyses have been performed, and optimal robust results of the active tuned mass damper design parameters with their effectiveness in reducing the example building responses have been presented. Uncertainties, which may exist in the system, have been taken into account using a robust design optimization procedure. The stiffness matrix and damping ratio of the building are considered as uncertain random variables; and using the well-known beta distribution, 50 pairs of these variables are generated. This resulted in 50 buildings with different stiffness matrices and damping ratios. These simulated buildings are used to evaluate robust optimal values of the active tuned mass damper design parameters. Four non-commensurable objective functions, namely maximum displacement, maximum velocity, maximum acceleration of each floor of the building, and active control force produced by the actuator are considered, and a fast and elitist non-dominated sorting genetic algorithm approach is used to find a set of pareto-optimal solutions.

Sign in / Sign up

Export Citation Format

Share Document