scholarly journals Strength Behavior of Flat and Folded Fly Ash-Based Geopolymer Ferrocement Panels under Flexure and Impact

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Dharmar Sakkarai ◽  
Nagan Soundarapandian
Keyword(s):  
Fly Ash ◽  
Impact Strength ◽  
Flexural Strength ◽  
Single Layer ◽  
Wire Mesh ◽  
Industrial Sectors ◽  
Heat Curing ◽  
Strength Behavior ◽  
Predominant Factor ◽  
The Impact

This paper presents the impact of fiber and wire mesh layers on the strength behavior of flat as well as folded fly ash-based geopolymer ferrocement panels. The behaviors, namely, flexural strength, impact strength, ductility, stiffness, and cracking patterns, are observed. With the objective of decreasing CO2 emissions, concrete utilizes wastes such as fly ash disposed by industrial sectors. Six panels (three flat and three folded) were cast utilizing a fly ash-dependent geopolymer mortar of size 1000 mm × 400 mm × 30 mm in addition to two panels of each type for the impact study. Heat curing in a temperature-controlled chamber maintaining 75°C to 80°C for 24 hours was done after 24 hours of the resting period. The experimental results indicated that the flexural strength got enhanced by 33 percent by increasing the quantity of wire mesh layers, but the ductility got decreased by 30 percent for the flat panels; however, there was no noticeable impact in the case of folded panels. The flexural strength of the folded panel was found to be three times greater than that of the flat panels. In addition, it is noticed that the behavior of the fiber-reinforced flat as well as folded panels of single layer mesh is stronger than the double layer wire mesh panels regarding cracking and ultimate load. Furthermore, the impact strength of the folded panels was found to be 90% greater than that of flat panels, and the energy absorbed at failure was directly proportional to the volume of reinforcement provided in the panels. Moreover, the failure pattern of the impact tested specimens showed punching shear as the predominant factor.

scholarly journals Flexural behavior of flat and folded geopolymer ferrocement panels

2021 ◽  
Author(s):  
Dharmar Sakkarai ◽  
◽  
Nagan Soundarapandian ◽  
Keyword(s):  
Fly Ash ◽  
Flexural Strength ◽  
Single Layer ◽  
Wire Mesh ◽  
Flexural Behavior ◽  
Industrial Sectors ◽  
Heat Curing ◽  
Strength Behavior ◽  
The Impact ◽  
Resting Period

This paper presents the impact of fiber and wire mesh layers on the strength behavior of flat as well as folded fly ash-based geopolymer ferrocement panels. The behavior, including flexural strength, ductility, stiffness, and cracking patterns are observed. With an objective of decreasing CO2 emissions, the concrete utilizes wastes such as fly ash disposed by industrial sectors. Six panels (three flat and three folded) were cast utilizing fly ash dependent geopolymer mortar of size 1000mm x 400mm x 30mm. Heat curing in a temperature-controlled chamber maintaining 75○C to 80○C for 24 hours was done after 24 hours of resting period. The experimental results indicated that the flexural strength got enhanced by 33 percent by increasing the quantity of wire mesh layers, but the ductility got decreased by 30 percent for the flat panels; however, there was no noticeable impact in case of folded panels. The flexural strength of folded panels was found to be three times greater than that of flat panels. In addition, it is noticed that the behavior of fiber reinforced flat as well as folded panels of single layer mesh is stronger than double layer wire mesh panels with regard to cracking and ultimate load. The energy absorbed at failure was directly proportional to the volume of the reinforcement provided in the panels.

scholarly journals Impact Strength of Ferrocement Panel under Low Velocity Impact Loading

2021 ◽  
Vol 10 (5) ◽  
pp. 285-291
Author(s):  
Darshan G. Gaidhankar ◽  
Mohammad Omid Naqshbandi ◽  
M. S. Kulkarni
Keyword(s):  
Impact Strength ◽  
Flexural Strength ◽  
Energy Absorption ◽  
Experimental Work ◽  
Impact Load ◽  
Impact Testing ◽  
Steel Fibers ◽  
Wire Mesh ◽  
Drop Weight ◽  
The Impact

The capability to absorb energy, often called as toughness, is of importance in actual service conditions of mesh reinforced composites, when they may be subjected to static, dynamic and fatigue loads. Toughness evaluated under impact loads is the impact strength. The toughness of materials are determined by two methods, (i) by measuring deformation under impact load, (ii) by determining energy adsorption capacity of materials under impact load. Several methods were used to investigate to determining toughness of materials. In this research work, drop weight impact test were used. The present experimental work describes testing of flat ferrocement panels with different number of layer steel mesh as well as enhancement of panels with steel fiber. The main purpose of this study is to investigate the effect of using different number of wire mesh layer on the flexural strength and impact strength and also effect of varying thickness of panels on the energy absorption of ferrocement panels. The experimental work includes preparation of ferrocement panels reinforced with welded square mesh, woven square mesh with and without hooked steel fibers The ferrocement panels of different sizes were prepared and tested for flexural strength under the two point loading as well as drop weight for impact testing. It is expected that as the mesh layers will be increased the energy absorption capacity of the panel should be increased and the also its effect should be seen for addition of hooked steel fibers.

Fly ash-based green composite as pipe, gear and blade

2018 ◽  
Vol 15 (1) ◽  
pp. 40-47
Author(s):  
Jenarthanan MP ◽  
Ramesh Kumar S. ◽  
Akhilendra Kumar Singh
Keyword(s):  
Experimental Investigation ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Impact Strength ◽  
Flexural Strength ◽  
Axial Flow ◽  
Green Composites ◽  
Content Type ◽  
The Impact

Purpose This paper aims to perform an experimental investigation on the impact strength, compressive strength, tensile strength and flexural strength of fly ash-based green composites and to compare with these polyvinyl chloride (PVC), high density polyethylene (HDPE) and low density polyethylene (LDPE). Design/methodology/approach Fly ash-based polymer matrix composites (FA-PMCs) were fabricated using hand layup method. Composites containing 100 g by weight fly ash particles, 100 g by weight brick dust particles and 50 g by weight chopped glass fiber particles were processed. Impact strength, compressive strength, tensile strength and flexural strength of composites have been measured and compared with PVC, HDPE and LDPE. Impact strength of the FA-PMC is higher than that of PVC, HDPE and LDPE. Structural analysis of pipes, gears and axial flow blade was verified using ANSYS. Barlou’s condition for pipes, Lewis–Buckingham approach for gears and case-based analysis for axial flow blades were carried out and verified. Findings Pipes, gears and axial flow blades made form fly ash-based composites were found to exhibit improved thermal resistance (i.e. better temperature independence for mechanical operations), higher impact strength and longer life compared to those made from PVC, HDPE and LDPE. Moreover, the eco-friendly nature of the raw materials used for fabricating the composite brings into its quiver a new dimension of appeal. Originality/value Experimental investigation on the impact strength, compressive strength, tensile strength and flexural strength of fly ash-based green composites has not been attempted yet.

A novel recycled polyethylene terephthalate/polyamide 11 (rPET/PA11) thermoplastic blend

2021 ◽  
pp. 147776062110010
Author(s):  
Zahid Iqbal Khan ◽  
Zurina Binti Mohamad ◽  
Abdul Razak Bin Rahmat ◽  
Unsia Habib ◽  
Nur Amira Sahirah Binti Abdullah
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Practical Implication ◽  
Polyamide 11 ◽  
Recycled Polyethylene ◽  
Twin Screw ◽  
Electron Microscopy Analysis ◽  
The Impact

This work explores a novel blend of recycled polyethylene terephthalate/polyamide 11 (rPET/PA11). The blend of rPET/PA11 was introduced to enhance the mechanical properties of rPET at various ratios. The work’s main advantage was to utilize rPET in thermoplastic form for various applications. Three different ratios, i.e. 10, 20 and 30 wt.% of PA11 blend samples, were prepared using a twin-screw extruder and injection moulding machine. The mechanical properties were examined in terms of tensile, flexural and impact strength. The tensile strength of rPET was improved more than 50%, while the increase in tensile strain was observed 42.5% with the addition of 20 wt.% of PA11. The improved properties of the blend were also confirmed by the flexural strength of the blends. The flexural strength was increased from 27.9 MPa to 48 MPa with the addition of 30 wt.% PA11. The flexural strain of rPET was found to be 1.1%. However, with the addition of 10, 20 and 30 wt.% of PA11, the flexural strain was noticed as 1.7, 2.1, and 3.9% respectively. The impact strength of rPET/PA11 at 20 wt.% PA11 was upsurged from 110.53 to 147.12 J/m. Scanning electron microscopy analysis revealed a dispersed PA11 domain in a continuous rPET matrix morphology of the blends. This work practical implication would lead to utilization of rPET in automobile, packaging, and various industries.

Preparing of SMC Artificial Marble and its Mechanical Properties

2011 ◽  
Vol 55-57 ◽  
pp. 447-450 ◽  
Author(s):  
Jian Li ◽  
Zheng Qun Huang ◽  
Yan Qin
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fiber Length ◽  
Filler Content ◽  
Fiber Content ◽  
Molding Temperature ◽  
Overall Performance ◽  
The Impact

In this article, a kind of SMC artificial marble was prepared. In order to enhance the mechanical properties and prolong the using life of SMC artificial marble, some effects such as fiber content, filler content and molding temperature etc. on the mechanical properties were carefully studied, too. Results showed that the increase of fiber content could improve the impact strength of SMC artificial marble when the fiber length was 10mm and the increase of filler content would decrease the flexural strength of SMC artificial marble. And the molding temperature at the range of 130°C ~ 160°C had little influence on the mechanical properties of SMC artificial marble. Comparing with natural marble and casting marble, SMC artificial marble owed superior overall performance and it was much more suitable for industry production.

Electrical and Mechanical Properties of Carbon Aerogels / Phenolic Resin for Nanocomposites

2011 ◽  
Vol 236-238 ◽  
pp. 1725-1730 ◽  
Author(s):  
Wei Jen Chen ◽  
Ming Yuan Shen ◽  
Yi Luen Li ◽  
Chin Lung Chiang ◽  
Ming Chuen Yip
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Phenolic Resin ◽  
Surface Conductivity ◽  
Carbon Aerogels ◽  
Polymer Resin ◽  
The Impact ◽  
Humidity Environment

This study used carbon aerogels (CA) and phenolic resin in fixed proportations to produce nano high polymer resin, and used poly ehtylene oxide (PEO) as the modifying agent for phenolic resin to improve the mechanical properties of phenolic resin and promote the surface conductivity. The prepared nano high polymer resin and carbon cloth were made into nano-prepreg by using ultrasonic impregnation method, and a nano-prepreg composite material was prepared by using hot compacting and cut to test pieces to measure its mechanical properties and surface conductivity as well as the influence of temperature-humidity environment (85°C/168hr and 85°C/85%RH/168hr) on mechanical properties. The result showed that the surface conductivity increased by 64.55%, the tensile strength at room temperature increased by 35.7%, the flexural strength increased by 18.4%, and the impact strength increased by 101%. In hot environment (85°C/168hr), the tensile strength decreased by 23.8%, the flexural strength increased by 3.1%, and the impact strength increased by 84.6%. In high temperature-high humidity environment (85°C/85% RH/168hr), the tensile strength decreased by 29.6%, the flexural strength decreased by 17%, and the impact strength increased by 95.7%.Introduction

scholarly journals Effect of repeated disinfections by microwave energy on the physical and mechanical properties of denture base acrylic resins

2009 ◽  
Vol 20 (2) ◽  
pp. 132-137 ◽  
Author(s):  
Rafael Leonardo Xediek Consani ◽  
Douglas Duenhas de Azevedo ◽  
Marcelo Ferraz Mesquita ◽  
Wilson Batista Mendes ◽  
Paulo César Saquy
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
Knoop Hardness ◽  
Microwave Energy ◽  
Bending Test ◽  
Denture Base ◽  
Acrylic Resins ◽  
The Impact

The present study evaluated the effect of repeated simulated microwave disinfection on physical and mechanical properties of Clássico, Onda-Cryl and QC-20 denture base acrylic resins. Aluminum patterns were included in metallic or plastic flasks with dental stone following the traditional packing method. The powder/liquid mixing ratio was established according to the manufacturer's instructions. After water-bath polymerization at 74ºC for 9 h, boiling water for 20 min or microwave energy at 900 W for 10 min, the specimens were deflasked after flask cooling and finished. Each specimen was immersed in 150 mL of distilled water and underwent 5 disinfection cycles in a microwave oven set at 650 W for 3 min. Non-disinfected and disinfected specimens were subjected to the following tets: Knoop hardness test was performed with 25 g load for 10 s, impact strength test was done using the Charpy system with 40 kpcm, and 3-point bending test (flexural strength) was performed at a crosshead speed of 0.5 mm/min until fracture. Data were analyzed statistically by ANOVA and Tukey's test (α= 0.05%). Repeated simulated microwave disinfections decreased the Knoop hardness of Clássico and Onda-Cryl resins and had no effect on the impact strength of QC-20. The flexural strength was similar for all tested resins.

Preparation and Study of Flexural Strength and Impact Strength for Hybrid Composite Materials used in Structural Applications

2020 ◽  
Vol 38 (8A) ◽  
pp. 1117-1125
Author(s):  
Teeb A. Mohameed ◽  
Sihama I. Salih ◽  
Wafaa M. Salih
Keyword(s):  
Fracture Toughness ◽  
Impact Strength ◽  
Flexural Strength ◽  
Polymer Blends ◽  
Laminar Composite ◽  
Kevlar Fiber ◽  
Laminar Composites ◽  
Structural Applications ◽  
Materials Used ◽  
The Impact

 Many of the polymeric materials used for structural purposes have weak mechanical properties, these characteristics can therefore be improved by preparing a hybrid laminar composite. In this work use melting mixing method using screw extruder to prepare sheets of polymer blends and nanocomposites based on polymer blends, and using a hot hydraulic press machine to prepared hybrid laminates composites. Two groups of hybrid laminar composites were prepared, the first group is consist of [((94%PP: 5%PMMA: 1 %( PP-g-MA)): 0.3% ZrO2): 6%KF and 8%KF] and the second group is [((94%PP: 5%UHMWPE: 1 %( PP-g-MA)): 0.3% ZrO2): 6%KF and 8%KF]. The results illustrated the impact strength and fracture toughness are increase with increased weight percentage of Kevlar fiber in for both groups of laminar composites and the highest values for two groups are (58.1, 54.95 KJ/M2) and (8.4, 9.16 MPa√m) respectively, any that, at the rate of increment reached to (120.4%, 107%) and (52.7%, 66.5%) respectively, compared with the neat PP. Moreover, the flexural strength values of the first group samples of hybrid laminar composite remained constant, when added kevlar fiber to nanocomposite. While, the flexural strength values of the second group samples of hybrid laminar composite increase with increase the ratio of kevlar fiber in composite to reach the maximum values (92 MPa) at 8% wt. of kevlar fiber, any, at the rate of increment reached to 39.4% compared with the neat PP. As well as, the results shown that the flexural properties and fracture toughness of the second group samples higher than they are for the first group samples.

Effect of Tetradecyl Methyl Acrylate-Maleic Anhydride Copolymer on the Mechanical Properties of Glass Mat Reinforced Polypropylene Composites

2005 ◽  
Vol 13 (4) ◽  
pp. 403-413
Author(s):  
Shanhua Zhou ◽  
Zhiyu Xu ◽  
Xin Liu ◽  
Yan Gao ◽  
Qingzhi Dong
Keyword(s):  
Mechanical Properties ◽  
Maleic Anhydride ◽  
Impact Strength ◽  
Flexural Strength ◽  
Polypropylene Composites ◽  
Monomer Ratio ◽  
Maleic Anhydride Copolymer ◽  
Glass Mat ◽  
The Impact ◽  
Interfacial Modifier

A new interfacial modifier made of tetradecyl methylacrylate-maleic anhydride copolymer (TMA- co-MAH) was prepared and characterized. The effect of reaction time and monomer ratio on the gross conversion and MAH content in the copolymer was studied. When the glass mat was treated with TMA- co-MAH solutions and compounded with PP, the MAH group of the interfacial modifier formed strong interactions with the glass mat and the long side chain of the interfacial modifier entangled firmly with the polypropylene matrix. In comparison with maleated polyolefins, the higher MAH content of the TMA- co-MAH resulted in better interfacial adhesion between the PP and the glass mat resulting in increased flexural strength and modulus, and the ductility of the TMA- co-MAH introduced a ductile interlayer into the interface of the glass mat reinforced polypropylene composites (GMT-PPs) to achieve higher impact strength. Therefore the mechanical properties of composites treated with TMA- co-MAH were all superior to those of GMT-PPs treated with maleic anhydride grafted polypropylene (PP- g-MAH) solutions when they were used at the same level. The effects of anhydride content, concentration of copolymer and compounding time on the mechanical property of GMT-PPs were investigated. With the optimal monomer ratio, MAH:TMA = 7:3, a 3% copolymer solution and a compounding time of 5 min, the impact strength, flexural strength and modulus of GMT-PPs treated with the new interfacial modifier were all improved significantly compared with composites treated with 0.3% PP- g-MAH solution.

Sign in / Sign up

Export Citation Format

Share Document