Electrical and Mechanical Properties of Carbon Aerogels / Phenolic Resin for Nanocomposites

2011 ◽  
Vol 236-238 ◽  
pp. 1725-1730 ◽  
Author(s):  
Wei Jen Chen ◽  
Ming Yuan Shen ◽  
Yi Luen Li ◽  
Chin Lung Chiang ◽  
Ming Chuen Yip
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Phenolic Resin ◽  
Surface Conductivity ◽  
Carbon Aerogels ◽  
Polymer Resin ◽  
The Impact ◽  
Humidity Environment

This study used carbon aerogels (CA) and phenolic resin in fixed proportations to produce nano high polymer resin, and used poly ehtylene oxide (PEO) as the modifying agent for phenolic resin to improve the mechanical properties of phenolic resin and promote the surface conductivity. The prepared nano high polymer resin and carbon cloth were made into nano-prepreg by using ultrasonic impregnation method, and a nano-prepreg composite material was prepared by using hot compacting and cut to test pieces to measure its mechanical properties and surface conductivity as well as the influence of temperature-humidity environment (85°C/168hr and 85°C/85%RH/168hr) on mechanical properties. The result showed that the surface conductivity increased by 64.55%, the tensile strength at room temperature increased by 35.7%, the flexural strength increased by 18.4%, and the impact strength increased by 101%. In hot environment (85°C/168hr), the tensile strength decreased by 23.8%, the flexural strength increased by 3.1%, and the impact strength increased by 84.6%. In high temperature-high humidity environment (85°C/85% RH/168hr), the tensile strength decreased by 29.6%, the flexural strength decreased by 17%, and the impact strength increased by 95.7%.Introduction

Study on Application of Modified Polyethylene in Preparation of Wood-Plastic Composites

2010 ◽  
Vol 150-151 ◽  
pp. 379-385
Author(s):  
Qun Lü ◽  
Qing Feng Zhang ◽  
Hai Ke Feng ◽  
Guo Qiao Lai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
High Density Polyethylene ◽  
Wood Flour ◽  
Wood Plastic Composites ◽  
Plastic Composites ◽  
The Matrix ◽  
The Impact

The wood-plastic composites (WPC) were prepared via compress molding by using the blends of high density polyethylene (HDPE) and modified polyethylene (MAPE) as the matrix and wood flour (WF) as filler. The effect of MAPE content in the matrix on the mechanical properties of the matrix and WPC was investigated. It was shown that the change of MAPE content in the matrix had no influence on the tensile strength of the matrix, but markedly reduced the impact strength of the matrix. Additionally, it had significant influence on the strength of WPC. When the content of wood flour and the content of the matrix remained fixed, with increasing the content of MAPE in the matrix, the tensile strength and the flexural strength of WPC tended to increase rapidly initially and then become steady. Moreover, with the increasing of MAPE concentration, the impact strength of WPC decreased when the low content of wood flour (30%) was filled, but increased at high wood flour loading (70%).

Mechanical Property Improvement of Poly(Butylene Succinate) by Reinforcing with Modified Fumed Silica

2014 ◽  
Vol 1025-1026 ◽  
pp. 215-220 ◽  
Author(s):  
Sasirada Weerasunthorn ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fumed Silica ◽  
Tensile Modulus ◽  
Silica Particles ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Ir Spectrophotometry

Fumed silica particles (SiO2) were directly added into poly (butylene succinate) (PBS) by melt mixing process. The effects of amount of fumed silica particles on mechanical properties of PBS/fumed silica composites, those are tensile strength, tensile modulus, impact strength as well as flexural strength, were investigated. It was found that the mechanical properties decreased with increasing fumed silica loading (0-3 wt%). In order to increase polymer-filler interaction, fumed silica was treated with 3-glycidyloxypropyl trimethoxysilane (GPMS), and its structure was analyzed by FT-IR spectrophotometry. The PBS/modified was found to possess better tensile strength, tensile modulus, impact strength and flexural strength that those of PBS/fumed silica composites.

A novel recycled polyethylene terephthalate/polyamide 11 (rPET/PA11) thermoplastic blend

2021 ◽  
pp. 147776062110010
Author(s):  
Zahid Iqbal Khan ◽  
Zurina Binti Mohamad ◽  
Abdul Razak Bin Rahmat ◽  
Unsia Habib ◽  
Nur Amira Sahirah Binti Abdullah
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Practical Implication ◽  
Polyamide 11 ◽  
Recycled Polyethylene ◽  
Twin Screw ◽  
Electron Microscopy Analysis ◽  
The Impact

This work explores a novel blend of recycled polyethylene terephthalate/polyamide 11 (rPET/PA11). The blend of rPET/PA11 was introduced to enhance the mechanical properties of rPET at various ratios. The work’s main advantage was to utilize rPET in thermoplastic form for various applications. Three different ratios, i.e. 10, 20 and 30 wt.% of PA11 blend samples, were prepared using a twin-screw extruder and injection moulding machine. The mechanical properties were examined in terms of tensile, flexural and impact strength. The tensile strength of rPET was improved more than 50%, while the increase in tensile strain was observed 42.5% with the addition of 20 wt.% of PA11. The improved properties of the blend were also confirmed by the flexural strength of the blends. The flexural strength was increased from 27.9 MPa to 48 MPa with the addition of 30 wt.% PA11. The flexural strain of rPET was found to be 1.1%. However, with the addition of 10, 20 and 30 wt.% of PA11, the flexural strain was noticed as 1.7, 2.1, and 3.9% respectively. The impact strength of rPET/PA11 at 20 wt.% PA11 was upsurged from 110.53 to 147.12 J/m. Scanning electron microscopy analysis revealed a dispersed PA11 domain in a continuous rPET matrix morphology of the blends. This work practical implication would lead to utilization of rPET in automobile, packaging, and various industries.

scholarly journals ANALISIS KEKUATAN TARIK DAN IMPAK MATERIAL KOMPOSIT POLIMER DALAM APLIKASI FIBERBOAT

2021 ◽  
Vol 4 ◽  
pp. 121-126
Author(s):  
Rezza Ruzuqi ◽  
Victor Danny Waas
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Impact Strength ◽  
Metal Corrosion ◽  
Phase System ◽  
Low Density ◽  
Weight Percentage ◽  
Multi Phase ◽  
The Impact

Composite material is a material that has a multi-phase system composed of reinforcing materials and matrix materials. Causes the composite materials to have advantages in various ways such as low density, high mechanical properties, performance comparable to metal, corrosion resistance, and easy to fabricate. In the marine and fisheries industry, composite materials made from fiber reinforcement, especially fiberglass, have proven to be very special and popular in boat construction because they have the advantage of being chemically inert (both applied in general and marine environments), light, strong, easy to print, and price competitiveness. Thus in this study, tensile and impact methods were used to determine the mechanical properties of fiberglass polymer composite materials. Each test is carried out on variations in the amount of fiberglass laminate CSM 300, CSM 450 and WR 600 and variations in weight percentage 99.5% -0.5%, 99% -1%, 98.5% -1, 5%, 98% -2% and 97.5%-2.5% have been used. The results showed that the greater the number of laminates, the greater the impact strength, which was 413,712 MPa, and the more the percentage of hardener, the greater the impact strength, which was 416,487 MPa. The results showed that the more laminate the tensile strength increased, which was 87.054 MPa, and the more the percentage of hardener, the lower the tensile strength, which was 73.921 MPa.

Preparing of SMC Artificial Marble and its Mechanical Properties

2011 ◽  
Vol 55-57 ◽  
pp. 447-450 ◽  
Author(s):  
Jian Li ◽  
Zheng Qun Huang ◽  
Yan Qin
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fiber Length ◽  
Filler Content ◽  
Fiber Content ◽  
Molding Temperature ◽  
Overall Performance ◽  
The Impact

In this article, a kind of SMC artificial marble was prepared. In order to enhance the mechanical properties and prolong the using life of SMC artificial marble, some effects such as fiber content, filler content and molding temperature etc. on the mechanical properties were carefully studied, too. Results showed that the increase of fiber content could improve the impact strength of SMC artificial marble when the fiber length was 10mm and the increase of filler content would decrease the flexural strength of SMC artificial marble. And the molding temperature at the range of 130°C ~ 160°C had little influence on the mechanical properties of SMC artificial marble. Comparing with natural marble and casting marble, SMC artificial marble owed superior overall performance and it was much more suitable for industry production.

A method to improve dimensional accuracy and mechanical properties of injection molded polypropylene parts

2017 ◽  
Vol 37 (4) ◽  
pp. 323-334 ◽  
Author(s):  
Shuai Li ◽  
Guoqun Zhao ◽  
Jiachang Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Injection Molding ◽  
Weld Line ◽  
Dimensional Accuracy ◽  
Holding Time ◽  
Dimensional Shrinkage ◽  
Injection Molded ◽  
The Impact

Abstract Gas counter pressure (GCP) technology can impose a reverse pressure to melt and thereby effectively increase the pressure acting on the melt at flow front. Theoretically, it has a potential to solve some defects often occurring in conventional injection molding (CIM) process. This paper designed and manufactured a GCP injection mold. GCP injection molding experiments were conducted. Effects of GCP process on melt flow and density, dimensional accuracy, and mechanical properties of molded samples were investigated. The results showed that GCP process can effectively inhibit the “fountain effect” in melt filling process, decrease the dimensional shrinkage of molded samples, increase dimensional accuracy of samples, and effectively improve impact property of samples. For the samples without weld line, tensile strength and flexural strength of GCP injection molded samples are slightly increased in comparison with those of CIM samples, but for the samples with weld line, GCP process can greatly improve the tensile strength and flexural strength of molded samples. When GCP is 9 MPa and GCP holding time is 10 s, the dimensional accuracy of molded samples without weld line, the tensile strength and flexural strength of the molded samples with weld line all increase up to maximum values. In comparison with CIM samples, the dimensional shrinkage of samples without weld line decreases by 17.2%, the tensile strength and flexural strength of samples with weld line increase by 30.51% and 23.69%, respectively. The impact value of the samples molded by process parameter combination of GCP 9 MPa and GCP holding time 20 s is the highest, and the impact value increases by 18.65%.

scholarly journals Effect of repeated disinfections by microwave energy on the physical and mechanical properties of denture base acrylic resins

2009 ◽  
Vol 20 (2) ◽  
pp. 132-137 ◽  
Author(s):  
Rafael Leonardo Xediek Consani ◽  
Douglas Duenhas de Azevedo ◽  
Marcelo Ferraz Mesquita ◽  
Wilson Batista Mendes ◽  
Paulo César Saquy
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
Knoop Hardness ◽  
Microwave Energy ◽  
Bending Test ◽  
Denture Base ◽  
Acrylic Resins ◽  
The Impact

The present study evaluated the effect of repeated simulated microwave disinfection on physical and mechanical properties of Clássico, Onda-Cryl and QC-20 denture base acrylic resins. Aluminum patterns were included in metallic or plastic flasks with dental stone following the traditional packing method. The powder/liquid mixing ratio was established according to the manufacturer's instructions. After water-bath polymerization at 74ºC for 9 h, boiling water for 20 min or microwave energy at 900 W for 10 min, the specimens were deflasked after flask cooling and finished. Each specimen was immersed in 150 mL of distilled water and underwent 5 disinfection cycles in a microwave oven set at 650 W for 3 min. Non-disinfected and disinfected specimens were subjected to the following tets: Knoop hardness test was performed with 25 g load for 10 s, impact strength test was done using the Charpy system with 40 kpcm, and 3-point bending test (flexural strength) was performed at a crosshead speed of 0.5 mm/min until fracture. Data were analyzed statistically by ANOVA and Tukey's test (α= 0.05%). Repeated simulated microwave disinfections decreased the Knoop hardness of Clássico and Onda-Cryl resins and had no effect on the impact strength of QC-20. The flexural strength was similar for all tested resins.

scholarly journals Mechanical Properties for Elephant Dung and its Utilization as a Raw Material Composites Sheet: A Study

2021 ◽  
Vol 10 (1) ◽  
pp. 1-7
Author(s):  
Rohit Kumar ◽  
Ramratan . ◽  
Anupam Kumar ◽  
Rajinder Singh Smagh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Polymer Composite ◽  
Natural Fiber ◽  
Testing Machine ◽  
Raw Material ◽  
Weight Percentage ◽  
The Impact ◽  
Elephant Dung

Elephant dung is an excellent source of cellulosic fiber that is a basic requirement for paper making. But they contributed to very small percentage production of elephant dung. So, researchers are trying to find a new area of utilization of elephant dung fiber pulp as in reinforcement’s polymer composite. In this experiment element dung fiber pulp in the natural fiber component chemically treated with alkaline and soda AQ solution in this study, it has been aimed to use elephant dung fiber pulp in composite material and to study mechanical properties of the produced material. The produced composite samples were then characterized using tensile test, Izod impact test, thickness test. The fracture surface of the polymer composite sample was also inspected with the help of SEM. The content of elephant dung fiber pulp is varied (35%, 45%, 55%) weight percentage whereas the epoxy resin is varied (50%, 40%, 30%) percentage is kept constant 15% in hardener. The entire sample has been tested in a universal testing machine as per ASTM standard for tensile strength and impact strength. It is observed that composite with 35% fiber pulp is having the highest tensile strength of 4mm 6.445 Mpa and 8mm 11.80 Mpa. The impact strength of composite with 35% fiber pulp washes highest than 45% to 55% dung fiber pulp. This produces composite sheet will be used for the surfboards, sporting goods, building panel this not only reduces the cost but also save from environmental pollution.

Mechanical Properties of Reinforced Polymer Concrete with Three Types of Resin Systems

2022 ◽  
pp. 1-24
Author(s):  
Mostafa Hassani Niaki ◽  
Morteza Ghorbanzadeh Ahangari ◽  
Abdolhossein Fereidoon
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Polyurethane Foam ◽  
Basalt Fiber ◽  
Polymer Concrete ◽  
Weight Percentage ◽  
Reinforced Polymer

This paper studies the mechanical properties of polymer concrete (PC) with three types of resin systems. First, the effect of 0.5 wt% up to 3 wt% basalt fiber on the mechanical properties of a quaternary epoxy-based PC is investigated experimentally, and the best weight percentage of basalt fiber is obtained. The results show that adding basalt fiber to PC caused the greatest enhancement within 10% in compressive strength, 10% in flexural strength, 35% in the splitting tensile strength, and 315% in impact strength. In the next step, the effect of nanoclay particles on the mechanical properties of basalt fiber-reinforced PC (BFRPC) is analyzed experimentally. Nanoclays increase the compressive strength up to 7%, flexural strength up to 27%, and impact strength up to 260% but decrease the tensile strength of the PC. Field-emission scanning electron microscopy (FESEM) analysis is performed to study the fracture surface and morphology of various concrete specimens. In the last step, we consider the effect of two other different resin systems, rigid polyurethane and rigid polyurethane foam on the mechanical properties of reinforced polymer concrete. A comparison study presents that the epoxy PC has a higher specific strength than the polyurethane and ultra-lightweight polyurethane foam PC.

The Effects of a Compatibilizer for Improving Mechanical Properties on Polymer Matrix Composites

2021 ◽  
Vol 877 ◽  
pp. 3-8
Author(s):  
Prathumrat Nuyang ◽  
Atiwat Wiriya-Amornchai ◽  
Watthanaphon Cheewawuttipong
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Young’S Modulus ◽  
Polymer Matrix ◽  
Polymer Matrix Composites ◽  
Fine Powder ◽  
Matrix Composites ◽  
Elongation At Break ◽  
The Impact

The effect of compatibilizer agent was studied when adding Aluminum fine powder (Al) to reinforce in Polypropylene (PP) by compared between polymer matrix composites (PMCs) and PMCs added Polypropylene graft maleic anhydride (PP-g-MAH).The average particle size of the aluminum fine powder was around 75 μm filled in polypropylene with different proportions of 2.5, 5, 7.5 and 10wt%. PMCs were prepared using the internal mixer. The results found that when the amount of aluminum fine powder increased, the mechanical properties had changed, i.e., tensile strength, and Young’s Modulus increased, while the impact strength and elongation at break decreased. But, when adding compatibilizer 1wt% it was found that the trend of tensile strength, and Young’s Modulus increased that compared with non-compatibilizer, but the impact strength and elongation at break decreased. The part of the morphology of PMCs with non-compatibilizer was found that the particle of aluminum fine powder dispersed in the matrix phase, but there were many microvoids between filler and matrix. But, PMCs with compatibilizer caused the microvoids between filler and matrix to be reduced.

Sign in / Sign up

Export Citation Format

Share Document