scholarly journals Experimental Study on Static Performance of Deployable Bridge Based on Cable-Strengthened Scissor Structures

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Xiaoming Yu ◽  
Yinghua Yang ◽  
Yanxia Ji ◽  
Lin Li
Keyword(s):  
Stress Distribution ◽  
Bearing Capacity ◽  
Three Dimensional ◽  
Bending Moment ◽  
Rapid Expansion ◽  
Load Bearing ◽  
Static Performance ◽  
Storage Rate ◽  
Steel Cables ◽  
High Storage

The deployable bridge based on scissor structures is one of the effective methods to quickly restore traffic after natural and man-made disasters. Scissor structures have the advantages of high storage rate, lightweight, and convenient storage and transportation. However, when scissor structures are used as load-bearing structures, their stiffness and bearing capacity are low. In this study, a three-dimensional deployable bridge based on the cable-strengthened scissor structures was proposed. In addition to rapid expansion, steel cables were used to strengthen scissor structures to improve the stiffness and bearing capacity. Besides, the static loading comparative tests on cable-strengthened scissor structures and traditional scissor structures (cable-free scissor structures) were performed. The results show that the stiffness of the cable-free scissor structure is small, the bending moment of members is large, and the stress distribution is uneven. The stiffness of cable-strengthened scissor structure is significantly improved; the bending moment of members is significantly reduced; and the stress distribution in the member section is more uniform. It is proved that cables can be used to improve the stiffness and load-bearing capacity of scissor structures without affecting the deployability.

scholarly journals Numerical and Experimental Study on Deficient Short Steel Tubes Strengthened with CFRP Under Compression

2019 ◽  
Author(s):  
Mohammad Reza Ghaemdoust ◽  
Omid Yousefi ◽  
Kambiz Narmashiri ◽  
Masoumeh Karimian
Keyword(s):  
Bearing Capacity ◽  
Numerical Study ◽  
Three Dimensional ◽  
Local Buckling ◽  
Steel Tubes ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Steel Columns ◽  
Repair Costs ◽  
The Impact

In view of development and repair costs, support of structures is imperative. Several factors, for example, design and calculation errors, absence of appropriate installation, change of structures application, exhaustion, seismic tremor, fire and natural conditions diminish their strength. In such cases, structures have need of rehabilitation and restoration to achieve their original performance. One of the most up to date materials for retrofitting is carbon fiber reinforced polymer (CFRP) that can provide an amount of restriction to postpone buckling of thin steel walls. This paper provides a numerical and experimental investigation on CFRP strengthened short steel tubes with initial horizontal and vertical deficiency under compression. Ten square and circular specimens were tested to study effects of the following parameters: (1) position of deficiency, horizontal or vertical; (2) tube shape, square or circular; (3) CFRP strengthening. In the experiments, axial static loading was gradually applied and for the numerical study three-dimensional (3D) static nonlinear analysis method using ABAQUS software was performed. The results show that deficiency reduces load-bearing capacity of steel columns and the impact of horizontal deficiency is higher than the impact of vertical deficiency, in both square and circular tubes. Use of CFRP materials for strengthening of short steel columns with initial deficiency indicates that fibers play a considerable role on increasing load bearing capacity, reducing stress at the damage location, preventing deformation caused by deficiency and delaying local buckling. Both numerical and experimental outcomes are in good agreement, which underlines the accuracy of the models adopted.

Load-bearing capacity and characteristic forms of destruction of furniture joints made with rastex 15 and P-10 clamex fasteners

2019 ◽  
Vol 106 ◽  
pp. 38-48
Author(s):  
Maciej Sydor ◽  
PIOTR POHL
Keyword(s):  
Bearing Capacity ◽  
Load Capacity ◽  
Bending Moment ◽  
Shear Forces ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Angular Deflection ◽  
Maximal Load ◽  
Rigidity Coefficient ◽  
The Relationship

Load-bearing capacity and characteristic forms of destruction of furniture joints made with rastex 15 and P-10 clamex fasteners. The study tested the relationship between the load and angular deflection in furniture joints. The tests were carried out for two types of fasteners and five types of materials: chipboard, MDF, hardwood plywood, glued pine boards and glued oak boards. The furniture joint samples contained two fasteners preloaded only with a bending moment (without application of shear forces). The results were converted per single fastener specifying: its maximal load capacity, 50 mrad (2.9°) limit deflection and rigidity coefficient. It was found that rigidity is a better structural property of the tested joint types than their load capacity. As far as rigidity is concerned, the most durable is the combination of oak glued board – rastex 15 fastener (13.2 Nm bending moment per fastener), while the least durable combination is chipboard – clamex P-10 fastener (4.8 Nm bending moment per fastener). Photographic documentation of damaged furniture joint samples was prepared and analysed. In case of chipboard and MDF combinations (where the load is determined by the combined material), the combined boards suffer a disastrous damage, while in combinations of plywood boards and pine or oak glued boards, (where the capacity is determined by the fastener), both clamex P10 and rastex 15 fasteners are damaged.

scholarly journals Development of an Optimal Relief Method for the Palatal Plate by Stress Analysis

2021 ◽  
Author(s):  
Tomoko Mukai ◽  
Yuji Sato ◽  
Osamu Shimodaira ◽  
Junichi Furuya ◽  
Akio Isobe ◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Bearing Capacity ◽  
Stress Analysis ◽  
Three Dimensional ◽  
Distribution Volume ◽  
Palatal Plate ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Palatal Mucosa

Abstract Background: A maxillary-palate-shaped device for simultaneous measurement of bite force and palatal mucosal subsidence at the time of pain onset in dentate persons has been developed. However, palatal mucosal stress analysis in a simulation based on three-dimensional finite element analysis is effective for objective and efficient evaluation of various types of denture-supporting mucosa. Recently plate dentures are not easily modified after the completion of these dentures , so it is essential to effectively assess the sites and magnitude of relief at the time of preparation. However, there is considerable variation in the magnitude of optimal relief and relief range, and there are no guidelines that present these clearly, leading the surgeon to decide subjectively. Thus, this study aimed to develop an optimal relief method to improve the stress bearing capacity of the palatal mucosa.Objectives: The objective of this study, the borderline was set in steps. The changes in stress distribution in the palatal mucosa due to the selective relief of stresses above the borderline were evaluated using a three-dimensional finite element simulation. The purpose of this study was to develop an optimal relief method to improve the bearing capacity of the palatal mucosa.Methods: The objective of this study, the borderline, was set in steps. A three-dimensional finite element model for the pseudopalatal plate was prepared and used to evaluate the changes in stress distribution in the palatal mucosa due to the selective relief of stresses above the borderline. The resulting data were used to develop the optimal relief method.Results: In the relief model with a borderline of 0.04 MPa or higher, the distribution volume at which high stress of 0.20 MPa or higher is generated was approximately about 800%％ of that with the no-relief model, and in the relief model with a borderline of 0.06 MPa or higher, the respective ratio was approximately about 280％%. On the other hand, the relief models with borderline of 0.14 MPa or higher were about 60%. In the mid-palatal relief model, the distribution volume at which stress of 0.20 MPa or higher was generated was 180% of that in the relief model.Conclusions: The supportive strength of plates can be increased by selectively applying optimal relief rather than standard relief, allowing for easier and more effective plate-denture treatment.

An Analysis of Circular Bolted Flanged Joints on Solid Round Bars Subjected to External Bending Moments

2000 ◽  
Author(s):  
Toshiyuki Sawa ◽  
Tsuneshi Morohoshi ◽  
Akihiro Shimizu
Keyword(s):  
Stress Distribution ◽  
Contact Stress ◽  
Three Dimensional ◽  
Bending Moment ◽  
Theory Of Elasticity ◽  
Load Factor ◽  
Bending Moments ◽  
Sealing Performance ◽  
Contact Stress Distribution ◽  
Good Agreement

Abstract In designing bolted joints, it is important to know the contact stress distribution which governs the clamping effect or the sealing performance and to estimate the load factor (the ratio of an increment in axial bolt force to an external load) from bolt design standpoint. The clamping force by bolts and the external bending moment are axi-asymmetrical loads and not many investigations have seen reported which treat axi-asymmetrical. In this paper, the clamping effect, and the load factor for the case of solid round bars with circular flanges, subjected to external bending moments, are analyzed as an axi-asymmetrical problem using the three-dimensional theory of elasticity. Experiments were carried out concerning the contact stress distribution, and the load factor for the external bending moment (a relationship between an increment in axial bolt force, and external bending moment). The analytical results were in fairly good agreement with the experimental ones.

scholarly journals The mechanical effects of bulges developed around bark-included branch junctions of hazel (Corylus avellana L.) and other trees

Trees ◽  
2021 ◽  
Author(s):  
Duncan Slater
Keyword(s):  
Bearing Capacity ◽  
Compensatory Growth ◽  
Secondary Growth ◽  
Bending Moment ◽  
Tensile Tests ◽  
Corylus Avellana ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Analysis Of The Images ◽  
Corylus Avellana L

Abstract Key message Large bulges formed around bark-included branch junctions can be conceived of as ‘compensatory growth’. Despite Claus Mattheck’s hypothesis that ‘the larger the bulges, the more likely the branch junction is to fail’, this study identifies that the extent of the defect inside such bulges is key information in predicting the junction’s load-bearing capacity. Abstract A currently prevalent rule in European arboriculture is that if a bark-included branch junction in a tree is associated with a large bulge in-line with the plane of the included bark then it is more likely to fail than if there is a smaller bulge or the absence of bulging. This rule for arborists originates from an initial suggestion with no associated data and is not logically consistent with recent research into the effects of natural bracing in trees, nor guidance provided by the International Society of Arboriculture. This also raises the question of how to correctly interpret the function of these bulges formed at bark-included junctions: either as secondary growth that has been pushed to the side by internal growth pressures, or as compensatory growth developing around a weakened component. To test the veracity of this rule, 117 branch junctions of common hazel (Corylus avellana L.) were subjected to tensile tests, comprising of controls with no bark included within them and bark-included specimens exhibiting a range of bulge sizes. In addition, photographs from the failure of 110 bark-included junctions were categorized to assess the frequency of failed specimens with different degrees of bulging. The results of the mechanical testing identified three significant factors that affected the maximal bending moment of these branch junctions: their categorized morphology, the diameter ratio of the branch junction and the width of the included bark at the apex of the junction. Overall, and in each category of branch junction tested, the extent of bulging was not found to be a significant predictor of the junctions’ maximal bending moment. This finding was reinforced by the analysis of the images of bark inclusion failure where the most frequent bark inclusions to fail were those associated with little to no bulging. Both findings identify that the bulging would be better interpreted as compensatory growth. This study highlights the need for further research on the load-bearing capacity of bark-included branch junctions to better inform arborists and tree managers as substantial variations in their biomechanical performance have not yet been elucidated.

scholarly journals INTERACTION DIAGRAMS AXIAL FORCE-BENDING MOMENT FOR FIRE EXPOSED STEEL-CONCRETE COMPOSITE SECTIONS

2016 ◽  
Author(s):  
Milivoje Milanovic ◽  
Meri Cvetkovska
Keyword(s):  
Bearing Capacity ◽  
Cross Section ◽  
Axial Force ◽  
Bending Moment ◽  
Cross Sectional ◽  
Load Bearing ◽  
Composite Columns ◽  
Interaction Diagram ◽  
Steel Sections ◽  
The Cross

The bearing capacity of the column cross section can be determined from the interaction diagram moment-axial force (M–N). Fire induced temperatures cause reduction of the load-bearing characteristics of the constitutive materials, steel and concrete, and this effect directly reflects on the reduction of the axial force and the bending moment that could be accepted by the column cross section, respectively the interaction diagram of the column cross section is changed. The load bearing capacity of the steel-concrete composite columns exposed to fire from all four sides and loaded by axial force and uni-axial or bi-axial bending moments, was estimated on the basis of the changes in the interaction diagrams moment-axial force amd the results are presented in this paper. Different types of composite columns made of totally or partially encased steel sections, or concrete filled hollow sections were analyzed and a detailed discussion on the effects of the shape of the cross section and the cross sectional dimensions are presented.

scholarly journals Thin-walled profiles and their joint assembly units built with screws: numerical studies of load bearing capacity

2018 ◽  
Vol 196 ◽  
pp. 01008 ◽  
Author(s):  
Vadim Alpatov ◽  
Alexey Soloviev
Keyword(s):  
Bearing Capacity ◽  
Three Dimensional ◽  
Load Bearing Capacity ◽  
Thread Cutting ◽  
Load Bearing ◽  
Thin Walled Structures ◽  
Numerical Studies ◽  
Thin Walled ◽  
With Screws ◽  
Joint Assembly

There is a tendency to reduce weight of load-bearing metal structures being developed and successfully realized in modern building construction. This idea serves as a basis for a whole scientific direction, named Development and application of light steel thin-walled structures (LSTS). Among them, LTST built with pop-rivets and thread-cutting screws are most widespread due to their simplicity and relative cheapness This paper presents numerical studies of LSTS joint assembly units built with screws and their load bearing capacity. The peculiarity of these units consists in misalignment of joint elements. The calculation was performed in the SolidWorks Simulation System. The modeled node is a three-dimensional assembly consisting of solid components. The results of the study are as follows: 1) thin-walled profiles have a significant sensitivity to eccentricity; 2) it is unacceptable to disregard eccentricities for thin-walled profiles and their joint connections; 3) eccentricities should be compensated by measures to improve reliability in joint connections design.

Sign in / Sign up

Export Citation Format

Share Document