scholarly journals Adsorption of Chromium (VI) by Cu (I)-MOF in Water: Optimization, Kinetics, and Thermodynamics

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Hongxue Qi ◽  
Xianjun Niu ◽  
Haipeng Wu ◽  
Xiuping Liu ◽  
Yongqiang Chen
Keyword(s):  
Adsorption Capacity ◽  
Low Cost ◽  
Entropy Change ◽  
Maximum Adsorption Capacity ◽  
Sem Images ◽  
First Order ◽  
Chromium Vi ◽  
Function Change ◽  
Pseudo Second Order ◽  
Pseudo First Order

To investigate the adsorption behavior of Cu (I)-MOF material for chromium (VI) in water, the parameters of influencing adsorption were optimized and found as follows: the optimal pH was 6 for the adsorption of Cr (VI) by the Cu (I)-MOF, the optimal amount of adsorbent was 0.45 g·L−1, and the adsorption saturation time was within 180 min. Subsequently, the kinetics results were fitted by four models such as pseudo-first-order, pseudo-second-order, Elovich, and intraparticle diffusion models. Among them, the adsorption of chromium (VI) was more inclined to the pseudo-first-order model (Radj2 = 0.9230). Then, the isotherm data were fitted by Langmuir and Freundlich models. The results indicated that Langmuir isotherm was the excellent match model (Radj2 = 0.9827). It belongs to a monolayer adsorption, and the maximum adsorption capacity was 95.92 mg·g−1. Subsequently, the thermodynamic parameters of the adsorption were calculated as follows: enthalpy change (ΔHθ) was −8.583 kJ·mol−1, entropy change (ΔSθ) was −8.243 J·mol−1 K−1, and the Gibbs function change (ΔGθ) was less than zero in the temperature range of 288–328 K, indicating that the reaction was spontaneous. Finally, both the spectra of infrared and XPS supported the adsorption mechanism that belonged the ion exchange. The spectra of XRD and SEM images shown that the structure of Cu (I)-MOF remained stable for at least 3 cycles. In conclusion, Cu (I)-MOF material has a high adsorption capacity, good water stability, low cost, and easy to prepare in large quantities in practical application. It will be a promising adsorbent for the removal of Cr (VI) from water.

Adsorption of Cr(III) from aqueous solutions by polyacrylamide-grafted rubberwood fibre: Kinetics, equilibrium, and thermodynamic studies

BioResources ◽  
2010 ◽  
Vol 6 (1) ◽  
pp. 22-33
Author(s):  
Mahnaz Mahdavi ◽  
Mansor B. Ahmad ◽  
Md Jelas Haron ◽  
Mohamad Zaki Ab. Rahman
Keyword(s):  
Adsorption Capacity ◽  
Metal Ion ◽  
Entropy Change ◽  
Ion Concentration ◽  
Ceric Ammonium Nitrate ◽  
Maximum Adsorption Capacity ◽  
First Order ◽  
Pseudo Second Order ◽  
Aqueous Conditions ◽  
Langmuir And Freundlich Models

Cr(III) ions were adsorbed onto polyacrylamide-grafted rubberwood fibre, and effects of aqueous conditions were evaluated. The adsorbent was prepared via graft copolymerization of acrylamide (Am) onto rubberwood fibre (RWF), using ceric ammonium nitrate as an initiator. Fourier transform infrared spectroscopy was used to confirm the formation of PAm-g-RWF. Various variables affecting the adsorption capacity such as the pH of the solution, adsorption time, initial metal ion concentration, and temperature were investigated. The Cr(III) was up to 92% removed by PAm-g-RWF from an initial concentration of 10 mg/L at pH 5.0. Kinetic data fitted very well to a pseudo-second-order rate expression and less well to a pseudo-first-order equation. The equilibrium parameters for adsorption isotherms of the metal ions on the grafted fibre were obtained using Langmuir and Freundlich models, and the Langmuir model was found to be in better correlation with the experimental data with a maximum adsorption capacity of 18.24 mg/g. Thermodynamic parameters such as enthalpy change (ΔH°), free energy change (ΔG°), and entropy change (ΔS°) were calculated; the adsorption process was spontaneous and endothermic.

Efficient adsorption of chlorpyrifos onto modified activated carbon by gamma irradiation; a plausible adsorption mechanism

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Mohamed S. Yahia ◽  
Ahmed S. Elzaref ◽  
Magdy B. Awad ◽  
Ahmed M. Tony ◽  
Ahmed S. Elfeky
Keyword(s):  
Gamma Irradiation ◽  
Area Measurement ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
First Order ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Pseudo First Order ◽  
Kinetics Of

Abstract Commercial Granulated Active Carbon (GAC) has been modified using 10 Gy dose Gamma irradiation (GAC10 Gy) for increasing its ability of air purification. Both, the raw and treated samples were applied for removing Chlorpyrifos pesticide (CPF) from ambient midair. Physicochemical properties of the two materials were characterized by Fourier Transform Infrared (FT-IR) and Raman spectroscopy. The phase formation and microstructure were monitored using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), supported with Energy-Dispersive X-ray (EDX). The Surface area measurement was detected using BET particle size prosometry. Obtained outcomes showed that, the maximum adsorption capacity, given by Langmuir equations, was greatly increased from 172.712 to 272.480 mg/g for GAC and GAC10 Gy, respectively, with high selectivity. The overall removal efficiency of GAC10 Gy was notably comparable to that of the original GAC-sorbent. The present study indicated that, gamma irradiation could be a promising technique for treating GAC and turned it more active in eliminating the pesticides pollutants from surrounding air. The data of equilibrium has been analyzed by Langmuir and Freundlich models, that were considerably better suited for the investigated materials than other models. The process kinetics of CPF adsorbed onto both tested carbon versions were found to obey the pseudo first order at all concentrations with an exception at 70 mg/l using GAC, where, the spontaneous exothermic adsorption of Chlorpyrifos is a strong function for the pseudo-first order (PFO) and pseudo second order (PSO) kinetics.

scholarly journals Equilibrium and Kinetic Study of Anionic and Cationic Pollutants Remediation by Limestone–Chitosan–Alginate Nanocomposite from Aqueous Solution

Molecules ◽  
2021 ◽  
Vol 26 (9) ◽  
pp. 2586
Author(s):  
Inas A. Ahmed ◽  
Ahmed H. Ragab ◽  
Mohamed A. Habila ◽  
Taghrid S. Alomar ◽  
Enas H. Aljuhani
Keyword(s):  
Physical Adsorption ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Entropy Change ◽  
Sem Images ◽  
Bet Analysis ◽  
Adsorption Processes ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Multilayer Formation

In this work, low-cost and readily available limestone was converted into nanolimestone chitosan and mixed with alginate powder and precipitate to form a triple nanocomposite, namely limestone—chitosan–alginate (NLS/Cs/Alg.), which was used as an adsorbent for the removal of brilliant green (BG) and Congo red (CR) dyes in aqueous solutions. The adsorption studies were conducted under varying parameters, including contact time, temperature, concentration, and pH. The NLS/Cs/Alg. was characterized by SEM, FTIR, BET, and TEM techniques. The SEM images revealed that the NLS/Cs/Alg. surface structure had interconnected pores, which could easily trap the pollutants. The BET analysis established the surface area to be 20.45 m2/g. The recorded maximum experimental adsorption capacities were 2250 and 2020 mg/g for CR and BG, respectively. The adsorption processes had a good fit to the kinetic pseudo second order, which suggests that the removal mechanism was controlled by physical adsorption. The CR and BG equilibrium data had a good fit for the Freundlich isotherm, suggesting that adsorption processes occurred on the heterogeneous surface with a multilayer formation on the NLS/Cs/Alg. at equilibrium. The enthalpy change (ΔH0) was 37.7 KJ mol−1 for CR and 8.71 KJ mol−1 for BG, while the entropy change (ΔS0) was 89.1 J K−1 mol−1 for CR and 79.1 J K−1 mol−1 BG, indicating that the adsorption process was endothermic and spontaneous in nature.

scholarly journals Harnessing of Newly Tailored Poly (Acrylonitrile)-Starch Nanoparticle Graft Copolymer for Copper Ion Removal via Oximation Reaction

2021 ◽  
Author(s):  
khaled Mostafa ◽  
H. Ameen ◽  
A. Ebessy ◽  
A. El-Sanabary
Keyword(s):  
Experimental Data ◽  
Adsorption Capacity ◽  
Graft Copolymer ◽  
Adsorption Kinetics ◽  
Copper Ions ◽  
Copper Ion ◽  
Second Order ◽  
First Order ◽  
Pseudo Second Order ◽  
Pseudo First Order

Abstract Our recently tailored and fully characterized poly (AN)-starch nanoparticle graft copolymer having 60.1 G.Y. % was used as a starting substrate for copper ions removal from waste water effluent after chemical modification with hydroxyl amine via oximation reaction. This was done to change the abundant nitrile groups in the above copolymer into amidoxime one and the resultant poly (amidoxime) resin was used as adsorbent for copper ions. The resin was characterized qualitatively via rapid vanadium ion test and instrumentally by FT-IR spectra and SEM morphological analysis to confirm the presence of amidoxime groups. The adsorption capacity of the resin was done using the batch technique, whereas the residual copper ions content in the filtrate before and after adsorption was measured using atomic adsorption spectrometry. It was found that the maximum adsorption capacity of poly (amidoxime) resin was 115.2 mg/g at pH 7, 400ppm copper ions concentration and 0.25 g adsorbent at room temperature. The adsorption, kinetics and isothermal study of the process is scrutinized using different variables, such as pH, contact time, copper ion concentration and adsorbent dosage. Different kinetics models comprising the pseudo-first-order and pseudo-second-order have been applied to the experimental data to envisage the adsorption kinetics. It was found from kinetic study that pseudo-second-order rate equation was better than pseudo-first-order supporting the formation of chemisorption process. While, in case of isothermal study, the examination of calculated correlation coefficient (R2) values showed that the Langmuir model provide the best fit to experimental data than Freundlich one.

Equilibrium, kinetic and thermodynamic studies of mercury adsorption on almond shell

2012 ◽  
Vol 65 (8) ◽  
pp. 1341-1349 ◽  
Author(s):  
Shokooh Sadat Khaloo ◽  
Amir Hossein Matin ◽  
Sahar Sharifi ◽  
Masoumeh Fadaeinia ◽  
Narges Kazempour ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Low Cost ◽  
Second Order ◽  
Ion Concentration ◽  
Physical Parameters ◽  
Maximum Adsorption Capacity ◽  
Almond Shell ◽  
Pseudo Second Order ◽  
Uptake Process ◽  
Reaction Equations

The application of almond shell as a low cost natural adsorbent to remove Hg2+ from aqueous solution was investigated. Batch experiments were carried out to evaluate the adsorption capacity of the material. The chemical and physical parameters such as pH, sorbent amount, initial ion concentration, and contact time were optimized for the maximum uptake of mercury onto the solid surface. Adsorption isotherms were expressed by Langmuir and Freundlich adsorption models, and the experimental data were found to fit the Langmuir model rather than the Freundlich. The maximum adsorption capacity obtained from the Langmuir isotherm was 135.13 mg/g. A kinetic study was carried out with pseudo-first-order and pseudo-second-order reaction equations and it was found that the Hg2+ uptake process followed the pseudo-second-order rate expression. The thermodynamic values, ΔG0, ΔH0 and ΔS0, indicated that adsorption was an endothermic and spontaneous process. The potential of this material for mercury elimination was demonstrated by efficient Hg2+ removal from a synthetic effluent.

scholarly journals Removal of Fluoride Ion from Water Using locally Produced Adsorbent

2019 ◽  
Vol 4 (12) ◽  
pp. 78-85
Author(s):  
Aboiyaa A. Ekine ◽  
Patience N. Ikenyiri ◽  
O. Hezekiah-Braye
Keyword(s):  
Particle Size ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Intraparticle Diffusion ◽  
Fluoride Ion ◽  
First Order ◽  
Egg Shells ◽  
Pseudo Second Order ◽  
Pseudo First Order

This Research investigated the adsorption capacity of locally prepared adsorbents from Egg shells for the removal of fluoride ion in well water. It evaluated the performance of these adsorbents calcinated at 3000C and modified with 1.0M HNO3 (trioxonitrate (v)) acid. Batch adsorber was used to allow for interaction between adsorbent (grounded Egg shells) with water containing fluoride ion. The batch experiment was performed with particle size of 2.12 contact time (60, 120, 180, 240, 300min), mass dosage (5g, 10g, 15g, 20g) and temperature (250C, 300C, 400C, 500C). The modified adsorbent was characterized to determine the physiochemical properties of grounded Egg shells (GE). Also the chemical composition of the modified adsorbent was analyzed to determine the percentage of calcium element required for the uptake of the fluoride ions in water for calcium as 39.68% for grounded Egg shells (GE). Percentage adsorption increased with increase in contact time, mass dosage and temperature for the adsorbent. The adsorption capacity was also determined which also increased with increase in contact time, temperature but decreased with increase in mass dosage at constant time of 60minutes. The pseudo first-order, pseudo second order and intraparticle diffusion kinetic models were fitted into the experimental results. The results obtained indicated that the pseudo first order and intraparticle diffusion models for the grounded Egg shells (GE) reasonably described the adsorption process very well whereas the pseudo second order model was not suitable for a calcinations temperature of 3000C and particle size of 2.12m. The adsorption isotherms were obtained from equilibrium experiment Performed at temperature of 25, 35, 45 and 550C. The result showed that Langmuir and Freundlich isotherm fitted perfectly the experimental data. However, the negative values of Gibb’s free energy indicated that adsorption was favourable and the positive enthalpy change H0 revealed that adsorption process was endothermic while the positive value of the entropy change signified increased randomness with adsorption.

scholarly journals Highly Effective Covalently Crosslinked Composite Alginate Cryogels for Cationic Dye Removal

Gels ◽  
2021 ◽  
Vol 7 (4) ◽  
pp. 178
Author(s):  
Serap Sezen ◽  
Vijay Kumar Thakur ◽  
Mehmet Murat Ozmen
Keyword(s):  
Adsorption Capacity ◽  
Dye Removal ◽  
Low Cost ◽  
Dye Adsorption ◽  
Maximum Adsorption Capacity ◽  
High Porosity ◽  
Order Model ◽  
Removal Capacity ◽  
Pseudo Second Order ◽  
The One

Currently, macroporous hydrogels have been receiving attention in wastewater treatment due to their unique structures. As a natural polymer, alginate is used to remove cationic dyes due to its sustainable features such as abundance, low cost, processability, and being environmentally friendly. Herein, alginate/montmorillonite composite macroporous hydrogels (cryogels) with high porosity, mechanical elasticity, and high adsorption yield for methylene blue (MB) were generated by the one-step cryogelation technique. These cryogels were synthesized by adding montmorillonite into gel precursor, followed by chemical cross-linking employing carbodiimide chemistry in a frozen state. The as-prepared adsorbents were analyzed by FT-IR, SEM, gel fraction, swelling, uniaxial compression, and MB adsorption tests. The results indicated that alginate/montmorillonite cryogels exhibited high gelation yield (up to 80%), colossal water uptake capacity, elasticity, and effective dye adsorption capacity (93.7%). Maximum adsorption capacity against MB was 559.94 mg g−1 by linear regression of Langmuir model onto experimental data. The Pseudo-Second-Order model was fitted better onto kinetic data compared to the Pseudo-First-Order model. Improved porosity and mechanical elasticity yielding enhanced dye removal capacity make them highly potential alternative adsorbents compared to available alginate/montmorillonite materials for MB removal.

scholarly journals Removal of Arsenite from Water by Ce-Al-Fe Trimetal Oxide Adsorbent: Kinetics, Isotherms, and Thermodynamics

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Cuizhen Sun ◽  
Jinwei Qiu ◽  
Zhibin Zhang ◽  
Taha F. Marhaba ◽  
Yanhao Zhang
Keyword(s):  
Adsorption Capacity ◽  
Standard Free Energy ◽  
Entropy Change ◽  
Maximum Adsorption Capacity ◽  
Transmission Electron ◽  
Adsorbent Surface ◽  
Adsorption Mode ◽  
Freundlich Adsorption Isotherm ◽  
Pseudo Second Order ◽  
Isotherms And Thermodynamics

Ce-Al-Fe trimetal oxide adsorbent was prepared. The morphology characteristics of the new adsorbent were analysed by the transmission electron microscope (SEM) method. The SEM results implied its ability in the adsorption of As (III). To verify the analyses, bench-scale experiments were performed for the removal of As (III) from water. In the experiments of adsorption, As (III) adsorption capacity of the trimetal oxide adsorbent was presented significantly higher than activated aluminium oxide and activated carbon. As (III) adsorption kinetics resembled pseudo-second-order adsorption mode. When initial As (III) concentration was 3, 8, and 10 mg·L−1, the maximum adsorption capacity achieved was 1.48, 3.73, and 5.12 mg·g−1, respectively. In addition, the experimental adsorption data were described well by the Freundlich adsorption isotherm model at 20, 30, and 40°C. The enthalpy change(ΔS), the standard free energy(ΔG), and entropy change(ΔH)indicated that the nature of As (III) adsorption was exothermic and spontaneous with increasing randomness on the interface of solid and liquid. And the adsorption mechanism can be interpreted as chemisorption with As (III) multilayer coverage formation on the adsorbent surface.

Chromium (VI) adsorption onto activated sulfate lignin

2009 ◽  
Vol 4 (2) ◽  
Author(s):  
Nassima Tazrouti ◽  
Moussa Amrani
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Analytical Data ◽  
Order Equation ◽  
Second Order ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Adsorption Model ◽  
Chromium Vi ◽  
Pseudo Second Order

Activated lignin having surface area of 1023 m2.g-1 has been prepared from sulfate lignin that was treated by 30 % H2O2 and carbonized at 300 °C in order to test the chromium (VI) adsorption from aqueous solution. The influence of contact time, pH, initial concentration of adsorbent and adsorbate and temperature on the adsorption capacity were investigated. The maximum removal of Cr(VI) was found to be 92,36 % at pH=2 and contact time of 80 min. Optimal concentration of lignin and Cr(VI) were found to be 3.8 g.l-1 and 180 mg.l-1, respectively. The adsorption kinetics was tested pseudo-first-order and pseudo-second-order equation. The analytical data were fitted well in a pseudo-second-order equation and the rate of removal of chromium was found to speed up with increasing temperature. Activation energy for the adsorption process was found to be 18.19 Kj.mol-1. The Langmuir and Freundlich adsorption isotherm models were applied to describe the isotherm and isotherm constants for the adsorption of Cr (VI) on lignin. These constants and correlation coefficients of the isotherm models were calculated and compared. Results indicated that Cr (VI) uptake could be described by the Langmuir adsorption model. The maximum adsorption capacity (qm) of Cr (VI) on lignin was 75.75 mg.g-1 at temperature of 40°C. The dimensionless equilibrium parameter (RL) signified a favorable adsorption of Cr (VI) on lignin and was found between 0.0601 and 0.818 (0<RL<1). The thermodynamic parameters like ΔG°, ΔS° and ΔH° were calculated and it has been found that the reaction was spontaneous and endothermic in nature. This study indicates that lignin has the potential to become an effective and economical adsorbent for removal Cr (VI) from the waste water.

Rice Husk Active Carbon as a Potential Low-Cost Adsorbent for TNT Wastewater

2011 ◽  
Vol 356-360 ◽  
pp. 1289-1292
Author(s):  
Dan Fu ◽  
Yi He Zhang ◽  
He Li Wang ◽  
Feng Zhu Lv
Keyword(s):  
Rice Husk ◽  
Active Carbon ◽  
Low Cost ◽  
Adsorption Properties ◽  
Second Order ◽  
Order Model ◽  
First Order ◽  
Pseudo Second Order ◽  
Pseudo First Order ◽  
And Diffusion

In this paper, the adsorption properties of TNT on Rice husk active carbon (RHAC) were investigated. The effects of contact time was examined. Kinetic data obtained at different concentrations were conducted using Lagergren’s pseudo first-order, pseudo second-order and diffusion models. The regression results showed that the adsorption kinetics was more accurately represented by pseudo second-order model. The study indicates that there is significant potential for RHAC as an adsorbent material for TNT removal from wastewater.

Sign in / Sign up

Export Citation Format

Share Document