scholarly journals Study on Water Characteristic Curve and Shear Characteristics of Typical Unsaturated Silty Clay in Shaoxing

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Ruiqian Wu ◽  
Youzhi Tang ◽  
Shaohe Li ◽  
Wei Wang ◽  
Ping Jiang ◽  
...  
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Unsaturated Soil ◽  
Direct Shear Test ◽  
Shear Test ◽  
Characteristic Curve ◽  
Friction Angle ◽  
Matric Suction ◽  
Silty Clay ◽  
Direct Shear

In order to probe into one simplified method to predict the shear strength of Shaoxing unsaturated silty clay, the test method combining unsaturated soil consolidation instrument and conventional direct shear instrument is used to study the shear strength, and the method is compared and verified with the results of equal suction direct shear test. The research results show that the soil water characteristic curve fitted by the measured data points and VG model has obvious stage characteristics in the range of 0~38 kPa, 38~910 kPa, and 910~10000 kPa. The shear strength of unsaturated soil measured by consolidation meter combined with conventional direct shear test is in good agreement with that measured by equal suction direct shear test in the range of 0~500 kPa. The results show that the shear strength, total cohesion, and effective internal friction angle of soil increase slightly with the increase of matric suction in the range of 0~38 kPa. When the matric suction increases from 38 kPa to 500 kPa, the shear strength and total cohesion force of the soil have similar stage characteristics with the SWCC, which first increases and then tends to be stable, while the effective internal friction angle changes slightly. Finally, taking the air-entry value as the demarcation point, an improved model of unsaturated shear strength is proposed by analyzing the error value. Compared with the measured value, the absolute value of relative error is basically kept in the range of 5%~10%, which is close to the measured value.

scholarly journals Influence of Structural Plane Microscopic Parameters on Direct Shear Strength

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Yanhui Cheng ◽  
Weijun Yang ◽  
Dongliang He
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Internal Friction ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Direct Shear ◽  
Stiffness Ratio ◽  
Structural Plane

Structural plane is a key factor in controlling the stability of rock mass engineering. To study the influence of structural plane microscopic parameters on direct shear strength, this paper established the direct shear mechanical model of the structural plane by using the discrete element code PFC2D. From the mesoscopic perspective, the research on the direct shear test for structural plane has been conducted. The bonding strength and friction coefficient of the structural plane are investigated, and the effect of mesoscopic parameters on the shear mechanical behavior of the structural plane has been analyzed. The results show that the internal friction angle φ of the structural plane decreases with the increase of particle contact stiffness ratio. However, the change range of cohesion is small. The internal friction angle decreases first and then increases with the increase of parallel bond stiffness ratio. The influence of particle contact modulus EC on cohesion c is relatively small. The internal friction angle obtained by the direct shear test is larger than that obtained by the triaxial compression test. Parallel bond elastic modulus has a stronger impact on friction angle φ than that on cohesion c. Under the same normal stress conditions, the shear strength of the specimens increases with particle size. The shear strength of the specimen gradually decreases with the increase of the particle size ratio.

scholarly journals Shear strength characteristics of Jerash expansive soil

2021 ◽  
Vol 3 (2) ◽  
pp. 74-80
Author(s):  
Talal Masoud
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Water Content ◽  
Direct Shear Test ◽  
Shear Test ◽  
Expansive Soil ◽  
Content Increase ◽  
Direct Shear ◽  
Initial Water ◽  
Angle Of Internal Friction

The results of the direct shear test on Jerash expansive soil show the effect of the initial water content on the cohesion (c) and on the angel of internal friction ( ) [shear strength parameters].it show that, as the initial water increase, the cohesion (c) of Jerash expansive soil also increase up to the shrinkage limit, after that increase of water even small amount, decrease the cohesion of the soil. On the other hand, the results of direct shear test show also  that as the water content increase, the angle of internal friction ( )remain unchanged up to shrinkage limit , any increase of water cause a large decrease on the angle of internal friction of Jerash expansive soil.

Shear strength of unsaturated soil interfaces

2009 ◽  
Vol 46 (5) ◽  
pp. 595-606 ◽  
Author(s):  
Tariq B. Hamid ◽  
Gerald A. Miller
Keyword(s):  
Shear Strength ◽  
Unsaturated Soil ◽  
Characteristic Curve ◽  
Matric Suction ◽  
Direct Shear ◽  
Direct Shear Tests ◽  
Strength Failure ◽  
Suction Control ◽  
Failure Envelopes ◽  
Fine Grained Soil

Unsaturated soil interfaces exist where unsaturated soil is in contact with structures such as foundations, retaining walls, and buried pipes. The unsaturated soil interface can be defined as a layer of unsaturated soil through which stresses are transferred from soil to structure and vice versa. In this paper, the shearing behavior of unsaturated soil interfaces is examined using results of interface direct shear tests conducted on a low-plasticity fine-grained soil. A conventional direct shear test device was modified to conduct direct shear interface tests using matric suction control. Further, the results were used to define failure envelopes for unsaturated soil interfaces having smooth and rough counterfaces. Results of this study indicate that matric suction contributes to the peak shear strength of unsaturated interfaces; however, postpeak shear strength did not appear to vary with changes in matric suction. Variations in net normal stress affected both peak and postpeak shear strength. Failure envelopes developed using the soil-water characteristic curve (SWCC) appeared to capture the nonlinear influence of matric suction on shear strength of soil and interfaces.

scholarly journals Determination of the Effect of Soil Particle Size Distribution on the Shear Behavior of Sand

2021 ◽  
Vol 5 (2) ◽  
pp. 125
Author(s):  
Mohammad Afrazi ◽  
Mahmoud Yazdani
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Particle Sizes ◽  
Direct Shear ◽  
Shear Tests ◽  
Direct Shear Tests

Many geotechnical problems require the determination of soil engineering properties such as shear strength. Therefore, the determination of the reliable values for this parameter is essential. For this purpose, the direct shear test, as one of the oldest tests to examine the shear strength of soils, is the most common way in laboratories to determine the shear parameters of soil. There are far too many variables that influence the results of a direct shear test. In this paper, a series of 10 × 10 cm direct shear tests were carried out on four different poorly graded sands with different particle size distributions to determine their shear behaviors. Four different poorly graded sands with a different median diameter or medium value of particle size distribution (D50) (0.2, 0.53, 1.3, and 2.3 mm) has been selected, and about 40 direct shear tests were conducted. It was concluded that a soil’s friction angle is affected by coarse-grained material. Accordingly, sandy soils with bigger particle sizes record a higher friction angle than soils containing small particles. The investigations also showed that sand with bigger particle sizes has a higher dilation angle. In addition, a non-linear regression analysis was performed to establish the exact relationship between the friction angle of the soil and the characteristics of the soil particles. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium provided the original work is properly cited.

Experimental Study on Shear Strength of Expansive Soil Improved by Lime - Weathered Sand

2013 ◽  
Vol 446-447 ◽  
pp. 1441-1447
Author(s):  
Meng Yun Huang ◽  
Jun Lai Xiong ◽  
Ji Bing Tang ◽  
Chi Long
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Direct Shear Test ◽  
Shear Test ◽  
Expansive Soil ◽  
Dry Density ◽  
Direct Shear ◽  
Mass Ratio ◽  
Angle Of Internal Friction ◽  
The Impact

This paper ananlyzes and contrasts the direct shear test of the expansive soil with different weathered sand dosage (mass ratio) and different lime dosage (mass ratio) in the case of the expansive soil with some water content and dry density .And try to analyzes and researches the impact of expansive soil improved by weathered sand and lime shear strength index . The direct shear test by the expansive soil mixed with different proportions of weathered sand and lime can be concluded that: mixing the weathered sand to improve the shear strength of expansive soil is effective, and cohesion gradually decreases with the increase of doped proportion of sand and the angle of internal friction first increases with the increase of doped proportion of sand and then decreases ;mixing of lime is effective to improve the shear strength of expansive soil, and cohesion gradually decreases with the increase of doped proportion of lime and angle of internal friction first increases and then decreases with the increase of doped proportion of lime. The shear strength of improved expansive soil can meet the subgrade filling with soil standards and at the same time the expansive soil improved by weathered sand and lime reduces the amount of lime and reduce project cost when to achieve the same shear strength standards.

scholarly journals Experimental Study on Variation Law and Mechanism of Soil Shear Strength Parameters along the Slope

2019 ◽  
Vol 2019 ◽  
pp. 1-11
Author(s):  
Yanhai Wang ◽  
Jianlin Li ◽  
Qiao Jiang ◽  
Yisheng Huang ◽  
Xinzhe Li
Keyword(s):  
Shear Strength ◽  
Direct Shear Test ◽  
Shear Test ◽  
Three Gorges Reservoir Area ◽  
Silty Clay ◽  
Direct Shear ◽  
Shear Strength Parameters ◽  
Strength Parameters ◽  
Undisturbed Soil ◽  
Soil Shear Strength

Under the action of rainwater seepage, geological origin, and human activities, the soil shear strength parameters will have spatial variability along the slope direction. After collecting samples of silty clay at a slope in the Three Gorges Reservoir area as the research object, not only the large-scale direct shear test was carried out on the site but also the direct shear test, water content test, density test, and particle grading analysis test were carried out in the laboratory with the undisturbed soil. The variation law and mechanism of soil shear strength parameters along slope were studied. The results indicate the following: (1) The coefficient of variation of shear strength parameters along the slope is relatively large. With the decrease of the elevation of the test location, the cohesion value tends to be strengthened, while the friction angle tends to degrade. (2) The mechanism of the variation law of soil shear strength parameters along the slope, which is mainly due to the decrease of the elevation, the decrease of the edges and angles between the particles, and the increase of the clay content is determined. (3) The variation model of shear strength parameters along the slope is proposed, which can provide a reference for relevant projects.

Improvement of the Shear Strength Parameters of a Granular Volcanic Soil Using Type I Portland Cement

2021 ◽  
Vol 896 ◽  
pp. 165-172
Author(s):  
Jordy Frank Viso Chachayma ◽  
Jhian Franco Torres Alvarez ◽  
Gary Durán Ramírez ◽  
Carlos Mario Fernández Díaz
Keyword(s):  
Shear Strength ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Natural Soil ◽  
Dry Density ◽  
Type I ◽  
Direct Shear ◽  
Volcanic Soil ◽  
Maximum Dry Density

The purpose of this research is to improve the parameters of shear strength in granular volcanic soil, by adding a percentage of Portland type I cement. The first step for this research was to classify the soil through a Granulometry test, according to the Unified Soil Classification System (USCS), the result was considered as a poorly graded sand with gravel also considered by The American Association of State Highway and Transportation Officials (AASHTO) as “A-1-b”. In addition, the compaction curve of the volcanic soil has a Maximum Dry Density (MDD) of 1.21 kg/cm2 and an optimum moisture content of 17.8%. Also, the friction angle of 33.5° and a cohesion of 0 kg/cm2, and the results of the Direct Shear Test indicate the Residual Stresses of 0.63, 1.34 and 2.65 kg/cm2 according to the Normal Stresses 1, 2 and 4 kg/cm2, respectively. The second step was to apply a Modified Proctor Test as following: one sample for natural soil and four samples adding 3%, 5%, 7% and 9% of cement. Finally, applied the Direct Shear Test: one sample for natural soil and three samples adding 3%, 5%, and 7% of cement after 7 days of curing, then three more samples are taken adding 3, 5% and 7% of cement at 14 days of curing. The results of the Modified Proctor Test of the volcanic soil with the addition of 5% cement has a maximum peak of a Maximum Dry Density of 1.33 kg/cm2 and with an Optimal Moisture Content of 22.7%, improved the MDD by 10% in regard to the natural soil. And the results of the Direct Shear Test shown in each sample an increase from 14.6% to 79.1% in the friction angle in comparison with the natural soil from 25.8% to 161.5% in shear strength. Likewise, the behavior of the volumetric deformation is shown, presenting a greater contraction when a normal stress of 1 kg/cm2 is applied and a greater expansion when a normal stress of 4 kg/cm2 is applied. Also, the volcanic soil at 7 days of curing with 7% cement addition increases its resistance by 67.34% and the volumetric variation decreases by 50% and the volcanic soil at 14 days of curing with 5% addition of cement increases its resistance by 103.40% and the volumetric variation decreases by 25%.

scholarly journals Direct Shear Test of Unsaturated Soil

2017 ◽  
Vol 21 (4) ◽  
pp. 183-188
Author(s):  
Peng He ◽  
Liuying Sun ◽  
Zhen Wang
Keyword(s):  
Shear Strength ◽  
Unsaturated Soil ◽  
Direct Shear Test ◽  
Shear Test ◽  
Test Scheme ◽  
Direct Shear ◽  
Shear Strength Parameters ◽  
Shear Tests ◽  
Direct Shear Tests ◽  
Good Agreement

The present study focuses on some tentative laboratory tests using a newly-constructed modified direct shear test apparatus. The single-stage and multistage direct shear tests were performed to determine the shear rate and test scheme of unsaturated shear test. Shear strength parameters of unsaturated soil in different conditions are obtained and the tests indicate good agreement with typical theories of unsaturated soil, the nonlinear matric suction failure envelope is determined. Some shear strength equations are also fitted through the experimental results. 

Sign in / Sign up

Export Citation Format

Share Document