scholarly journals Investigation on Acoustic Emission Kaiser Effect and Frequency Spectrum Characteristics of Rock Joints Subjected to Multilevel Cyclic Shear Loads

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-21
Author(s):  
Zhiqiang Hou ◽  
Changhong Li ◽  
Zhengyang Song ◽  
Yonggang Xiao ◽  
Chen Qiao ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Cyclic Loading ◽  
Frequency Spectrum ◽  
Rock Joints ◽  
Displacement Curve ◽  
Kaiser Effect ◽  
Cyclic Shear ◽  
Shear Damage ◽  
Spectrum Characteristics ◽  
Felicity Ratio

Rock joints have obvious acoustic emission (AE) Kaiser effect and Felicity effect under multilevel cyclic shear conditions. The TFD-20H/50J rock shear apparatus was used to carry out cyclic loading and unloading joint shear tests, and the acoustic emission parameters and frequency spectrum characteristics of the whole shearing process were analyzed. The results show that, under the cyclic loading, the shear stress-displacement curve forms several cyclic hysteresis loops, and the number of loops increases with the increase of normal stress. With the cycles increase, the shear damage gradually increases, and the Felicity ratio gradually decreases. The Felicity ratio at the final shear failure moment is about 0.94~0.99. The ratio of the RA value (rise time/amplitude) and the average frequency value (RA-AF) is used to classify the cracking mode of the joint sample. There are two AE crack signal types (tensile type and shear type) during shear damage. The peak frequency is displayed as high, medium, and low three frequency bands, which are distributed in the range of 0~35 kHz, 35~122 kHz, and 122~300 kHz, respectively. Both low-frequency and high-frequency signals account for less than 10%, and medium-frequency signals account for more than 90%. The research of the AE monitoring signals of multilevel shear behaviors can help understand the shear-friction mechanisms of rock joints.

Study on Acoustic Emission Signatures during the Process of Edge Chipping for Engineering Ceramics

2011 ◽  
Vol 697-698 ◽  
pp. 93-96 ◽  
Author(s):  
Xiu Jian Tang ◽  
Xin Li Tian ◽  
Jian Quan Wang ◽  
Ya Tao Mao ◽  
F.Q. Li
Keyword(s):  
Acoustic Emission ◽  
Fracture Process ◽  
Static Load ◽  
Average Frequency ◽  
Displacement Curve ◽  
Edge Chipping ◽  
Kaiser Effect ◽  
Engineering Ceramics ◽  
Highly Active ◽  
Fracture Processes

The developments of edge chipping for engineering ceramics are analyzed. An edge chipping experiment under static load is adopted to study the fracture process of edge chipping. The results show that the fracture processes of edge chipping under different edge distances are similar, which can be divided into four stages based on load-displacement curve. There is obviously Kaiser Effect during the fracture processes of edge chipping. Counts, average frequency, RMS, duration, amplitude and inverse calculation can be used to describe the process of edge chipping for engineering ceramics. Amplitude, duration and average frequency become highly active on the eve of fracture, which can be regard as the omens of edge chipping and used to predict the fracture of edge chipping.

scholarly journals Damage and fractal evolution trends of sandstones under constant-amplitude and tiered cyclic loading and unloading based on acoustic emission

2019 ◽  
Vol 15 (7) ◽  
pp. 155014771986102
Author(s):  
Dongxu Liang ◽  
Nong Zhang ◽  
Lixiang Xie ◽  
Guangming Zhao ◽  
Deyu Qian
Keyword(s):  
Acoustic Emission ◽  
Cyclic Loading ◽  
Damage Evolution ◽  
Damage Accumulation ◽  
Fractal Dimensions ◽  
Damage Variable ◽  
Constant Amplitude ◽  
Kaiser Effect ◽  
Cyclic Loading And Unloading ◽  
Loading And Unloading

It is of significance to study the damage and destruction of rock under cyclic loading in geotechnical engineering. We determined the trends in damage evolution of sandstone under constant-amplitude and tiered cyclic loading and unloading under uniaxial compression. The results of the study show that (1) the variation of acoustic-emission events was consistent with the stress curves and 89% of all acoustic-emission events occurred during the cycling stages. The observed Kaiser effect was more notable in tiered cycling. (2) The damage variable increased sharply in the cycling stages and its increment was 0.07 higher for tiered cycling than constant-amplitude cycling. Sandstone exhibited greater damage under tiered cyclic loading and unloading. (3) Equations for the evolution of the damage variable under the two cycle modes were obtained by fitting of experimental data. (4) The fractal dimensions of the constant-amplitude cycle were larger than those of the tiered cycle. The process of damage and destruction presents a trend of reducing fractal dimension. The damage accumulation of sandstone under tiered cycling was faster than under constant-amplitude cycling. These results provide references for damage and early warning of rock under both constant-amplitude and tiered cyclic loading and unloading.

scholarly journals Size Effect of Concrete Specimens on the Acoustic Emission Characteristics under Uniaxial Compression Conditions

2017 ◽  
Vol 2017 ◽  
pp. 1-12
Author(s):  
Jianbo Wu ◽  
Enyuan Wang ◽  
Xuekun Ren ◽  
Mingwei Zhang
Keyword(s):  
Acoustic Emission ◽  
Cyclic Loading ◽  
Uniaxial Compression ◽  
Stress Level ◽  
Peak Stress ◽  
Deformation And Failure ◽  
Nonlinear Growth ◽  
Concrete Materials ◽  
Felicity Ratio ◽  
Loading Methods

Acoustic emission (AE) experiments under uniaxial compression and cyclic loading-unloading compression conditions were performed using different sizes of cubic concrete specimens. The influences of the loading methods and the concrete sizes on the mechanical parameters and the concrete AE activities were analyzed. The loading method was found to have great impact on the deformation, failure, and energy dissipation of concrete materials. With the increase of the material size, the uniaxial compressive strength of the concrete specimens gradually decreased, while the corresponding strain of peak strength increased first and then decreased. The elasticity modulus fluctuated irregularly. Under the uniaxial compression conditions, five AE patterns corresponding to the deformation and failure of the concrete materials were observed. A significant nonlinear relationship was found between the AE and the stress level. The cumulative AE rings at the peak stress showed nonlinear growth with the increase of the concrete size. Based on an established relationship between the cumulative AE rings and the stress level, the necessary conditions for the existence of the quiet AE period were given. Under the uniaxial cyclic loading-unloading compression conditions, the Felicity ratio decreased first and then increased as the stress increased. The research results have some guiding significance to AE-based monitoring of internal stress evolution of coal, rock, and concrete materials and thereby enable assessment of their stability.

Experimental and numerical studies on fracture characteristics of notched granite beams under cyclic loading and unloading

2020 ◽  
Vol 56 (1) ◽  
pp. 3-17
Author(s):  
Xiaojing Li ◽  
Peijie He ◽  
Jianhui Tang ◽  
Xudong Chen
Keyword(s):  
Acoustic Emission ◽  
Cyclic Loading ◽  
Correlation Method ◽  
Average Frequency ◽  
Test System ◽  
Underground Engineering ◽  
Three Point Bending ◽  
Cyclic Loading And Unloading ◽  
Loading And Unloading ◽  
Felicity Ratio

In underground engineering, such as mining engineering and deep tunnel engineering, the rock is often loaded and unloaded repeatedly. The strength of rock under cyclic load is lower than that under static load. To obtain the fracture response of the rock, the three-point bending tests of notched granite beams under cyclic loading and unloading were carried out with Electro-hydraulic Servo Material Test System. The acoustic emission technology was adopted to monitor the acoustic emission events of sample in the process of fracture. It is revealed that the fracture toughness of granite under cyclic loading and unloading is lower than that under static loading. Based on the acoustic emission energy obtained from monitoring, the damage evolution during cyclic loading and unloading was analyzed. The fracture mode of granite samples is analyzed by the RA value-average frequency correlation method. And the Felicity ratio during the loading and unloading cycle was calculated to evaluate the severity of initial damage of the material. It is revealed that Kaiser effect appears only in the elastic deformation stage of cyclic loading unloading bending. The Holmquist–Johnson–Cook damage constitutive model and Weibull distribution were used to establish the heterogeneous granite model. And the three-point bending of the model under cyclic loading and unloading was simulated to disclose the crack growth mechanism of rock. The study may provide some references for rock instability control in geotechnical engineering construction.

Experimental Verification and Theoretical Analysis on Felicity Effect of Acoustic Emission in Concrete

2007 ◽  
Vol 353-358 ◽  
pp. 2333-2336
Author(s):  
Rui Fu Yuan ◽  
Yuan Hui Li ◽  
Xing Dong Zhao
Keyword(s):  
Acoustic Emission ◽  
Cyclic Loading ◽  
Constitutive Model ◽  
Stress Level ◽  
Damage Mechanics ◽  
Kaiser Effect ◽  
Loading Cycle ◽  
Previous Cycle ◽  
Felicity Effect ◽  
Good Coincidence

The experiment of acoustic emission (AE) on concrete specimens under uniaxial cyclic loading was conducted. The Kaiser effect of acoustic emission in concrete and the Felicity effect, which manifest the memorizing ability to the maximum previous stress level of Kaiser effect, were validated by the experiment. The mechanism of Felicity effect was analyzed based on the theory of statistical damage mechanics and a tentative AE factor constitutive model of brittle material under uniaxial cyclic loading was suggested. The curve of constitutive model is in good coincidence with the curve from the experiment. The experimental results showed that the Felicity effect became clearer along with the increasing of stress level. Each loading cycle would cause new damage inside the material, and the response of material to the new loading cycle is different from the previous cycle.

scholarly journals Experimental study on fracture properties of dam concrete under post-peak cyclic loading based on DIC and acoustic emission techniques

2021 ◽  
Author(s):  
Jingwu Bu ◽  
Huiying Xu ◽  
Xinyu Wu ◽  
Xudong Chen ◽  
Bo Xu
Keyword(s):  
Acoustic Emission ◽  
Cyclic Loading ◽  
Crack Length ◽  
Recovery Rate ◽  
Loading Rate ◽  
Strain Recovery ◽  
Kaiser Effect ◽  
Fracture Properties ◽  
Dam Concrete ◽  
Loading Procedure

In order to study the fracture properties of dam concrete under post-peak cyclic loading, wedge splitting tests with three loading rates (0.001 mm/s, 0.01 mm/s, 0.1 mm/s) were performed on notched cubic dam concrete specimens. Meanwhile, the acoustic emission (AE) and digital image correlation (DIC) technologies were used to record the crack propagation process of specimens. Test results show that the fracture of dam concrete has a significant rate effect: with the loading rate increases, the peak load increases, the slope of the post-peak P-CMOD curve gradually decreases and the stiffness degradation of dam concrete becomes more serious. The cumulative AE count shows a step increasing trend and has a Kaiser effect. The Kaiser effect decreases with the post-peak cyclic loading procedure, and with the loading rate increases, the Kaiser effect increases. With the increasing of loading rate, AE energy fluctuates violently and b value fluctuates frequently, indicating the damage of dam concrete becomes more serious. As the loading procedure, the damage of the specimen accumulates gradually, and the strain recovery rate decreases gradually. With the loading rate increases, the strain recovery rate decreases and the permanent crack increases. Based on the fictitious crack model, the effective crack length shows a gradual and steady rising trend. As the loading rate increases, the growth rate of the effective crack length becomes large.

scholarly journals On the Kaiser Effect of Rock under Cyclic Loading and Unloading Conditions: Insights from Acoustic Emission Monitoring

Energies ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 3255 ◽  
Author(s):  
Qingbin Meng ◽  
Yanlong Chen ◽  
Mingwei Zhang ◽  
Lijun Han ◽  
Hai Pu ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Cyclic Loading ◽  
Stress Level ◽  
Loading Rate ◽  
Transition Period ◽  
Failure Process ◽  
Future Application ◽  
Emission Characteristic ◽  
Kaiser Effect ◽  
Stress Point

The Kaiser effect reflects the memory of the loaded rock to the irreversible damage and deformation. The stress level, loading rate and lithology are the main factors affecting the Kaiser effect of the rock. To identify the accurate stress point of the Kaiser effect, the MTS 816 rock mechanics testing system and the DS5-A acoustic emission testing and analysis system were adopted. The uniaxial cyclic loading–unloading and acoustic emission characteristic test of 90 rock specimens from three types of rocks under different stress level and loading rate was carried out. The evolution of acoustic emission under uniaxial compression of the rock corresponds to the compaction stage, elastic stage, yield stage and post-peak stress drop stage of the rock deformation and failure process and is divided into the quiet period, transition period, active period and decay period of the acoustic emission. The larger the hardness of rock is, the earlier the stress point of the Kaiser effect appears. The loading stress level (σA) has appreciable influence on the Kaiser effect of the rock. When σA ≥ 0.7σc, the Kaiser effect disappears. Usually, the dilatancy stress (crack initiation stress) does not exceed 70% of the uniaxial compressive strength (σc) of the rock, and the stress point can be the threshold to determine whether the Kaiser effect occurs. The influence of loading rate (lr) on Felicity rate (FR) is relatively large when lr < 0.01 mm/s, and FR rapidly grows with increase of the loading rate. When lr ≥ 0.01 mm/s, the influence of the loading rate on FR is relatively small. The findings facilitate the future application of the Kaiser effect and improvement of the accuracy of the acoustic emission data interpretation.

scholarly journals Modelling of Rock Joints Interface under Cyclic Loading

2020 ◽  
Vol 42 (1) ◽  
pp. 36-47 ◽  
Author(s):  
Jan Maciejewski ◽  
Sebastian Bąk ◽  
Paweł Ciężkowski
Keyword(s):  
Cyclic Loading ◽  
Normal Load ◽  
Shear Bands ◽  
Yield Function ◽  
Rock Joints ◽  
Response Analysis ◽  
Material Interface ◽  
Cyclic Shear ◽  
Dilatancy Effect ◽  
Cyclic Shear Test

AbstractThe problem of numerical simulation of the material interface response under monotonic and cyclic loading is of fundamental scientific and engineering importance. In fact, such interfaces occur in most engineering and geotechnical structures. The present work is devoted to the deformational response analysis of contact interfaces under monotonic and cyclic loads. The class of materials includes rock and structural joints, soil structure interfaces, masonry and cementitious joints, localized shear bands and so on.The aim of the proposed model is to simulate the cyclic shear test under constant normal load. The associated dilatancy effect is associated with the configurational effects of asperity interaction or dilatancy of wear debris layer. The large primary asperities are assumed as responsible for interfacial dilation and small size asperities as governing frictional sliding and hysteresis response. The elliptic loading yield function is assumed to translate and rotate during progressive or reverse loading events. The model formulation is discussed and confronted with experimental data.

TIME TO THE END OF PRIMARY CONSOLIDATION (EOP) OF SOFT CLAYEY SOILS: CONCERNING THE EFFECT OF ATTERBERG’S LIMIT AND CYCLIC LOADING HISTORY

2019 ◽  
Vol 128 (2B) ◽  
pp. 29-41
Author(s):  
Trần Thanh Nhàn
Keyword(s):  
Cyclic Loading ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Clayey Soils ◽  
Loading History ◽  
Cyclic Shear ◽  
Wide Range ◽  
Primary Consolidation ◽  
Time Required

In order to observe the end of primary consolidation (EOP) of cohesive soils with and without subjecting to cyclic loading, reconstituted specimens of clayey soils at various Atterberg’s limits were used for oedometer test at different loading increments and undrained cyclic shear test followed by drainage with various cyclic shear directions and a wide range of shear strain amplitudes. The pore water pressure and settlement of the soils were measured with time and the time to EOP was then determined by different methods. It is shown from observed results that the time to EOP determined by 3-t method agrees well with the time required for full dissipation of the pore water pressure and being considerably larger than those determined by Log Time method. These observations were then further evaluated in connection with effects of the Atterberg’s limit and the cyclic loading history.

Sign in / Sign up

Export Citation Format

Share Document