scholarly journals Modeling and Analysis of 3 MW Solar Photovoltaic Plant Using PVSyst at Islamia University of Bahawalpur, Pakistan

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Faizan Ul Hassan Faiz ◽  
Rabia Shakoor ◽  
Abdur Raheem ◽  
Farhana Umer ◽  
Nadia Rasheed ◽  
...  

Conventional means of electrical energy generation are costly, create environmental pollution, and demand a high level of maintenance and also going to end one day. This has made it crucial to exploit the untapped prospective of the environmentally friendly renewable energy resources. To address this problem, present research proposed an efficient, everlasting, and environment-friendly grid-connected PV system at The Islamia University of Bahawalpur, Pakistan (latitude: 29° 22 ′ 34 ″ N, longitude: 71° 44 ′ 57 E). Bahawalpur is one of those sites where the potential of solar energy is immense. The global daily horizontal solar irradiance at the site is 1745.85 kWh/m2, having average solar irradiation of 5.9 kWh/m2 per day, and the ambient average temperature is about 25.7°C. In this research, the performance ratio and different power losses just like soiling, PV module losses, inverter, and losses due to temperature are taken into account and calculated by using PVSyst. The coal saving per day is 15369.3 kg which is equal to planting 147600 teak trees over a lifetime. The cost of the energy produced is 0.11 US $/kWh whereas in Pakistan the conventional energy tariff is 0.18 $/kWh. From the simulation results, the value of PR comes out 83.8%, and the CUF value is 16% with a total energy generation of 4908 MWh/year. The performance analysis of this grid-connected system would help in the designing, analysis, operation, and maintenance of the new grid-connected systems for different locations.

2019 ◽  
Author(s):  
Rishal Asri

Sunlight is energy that can be converted into electrical energy. One of the uses is by applying it to the roof ofthe building. The application in this building has restrictions such as the placement of the PV moduleshorizontally and vertically. In the study comparing the results of energy obtained from the PV system withhorizontal and vertical positions with a standard degree angle in the direction of azimuth sunlight. Positionusing the horizontal produces more energy and reaches a performance ratio of more than 80%.


2021 ◽  
Vol 7 (20) ◽  
pp. 202129
Author(s):  
Vivyane Alencar Marques Araújo do Nascimento ◽  
Taynara Bastos Trindade ◽  
Clarice Maia Carvalho

ANALYSIS OF PARAMETERS FOR PHOTOVOLTAIC SOLAR ENERGY GENERATION IN ACRE, BRAZILANÁLISIS DE PARÁMETROS PARA LA GENERACIÓN DE ENERGÍA SOLAR FOTOVOLTAICA EN ACRE, BRASILRESUMOEnergia solar é obtida através de placas solares fotovoltaicas com a função de captar a energia do sol e transformar em energia elétrica, aumentando a geração de energia solar nas regiões com maior captação de energia luminosa. Assim, neste artigo analisou-se os parâmetros para geração de energia solar fotovoltaica no Acre, Brasil. Coletou-se dados referentes a insolação, temperaturas máximas e mínimas, precipitação e umidade relativa no Instituto Nacional de Meteorologia, irradiação solar, no Centro de Referências para Energias Solar e Eólica Sérgio de S. Brito, regionais do Vale do Juruá e Vale do Acre, no período de 2015-2020. As análises foram quantitativas, utilizando o cálculo da média e cálculo do plano inclinado. Na comparação das regionais, o Vale do Acre apresentou melhores resultados para geração de energia solar e com um ângulo com a maior média diária anual de irradiação solar, considerando-se projetar-se células fotovoltaicas na regional. O trabalho apresenta que o Acre possui bastante insolação e irradiação solar, indicando alto potencial de geração de energia solar para as regionais do estado.Palavras-chave: Eficiência Fotovoltaica; Radiação Solar; Temperatura da Célula Fotovoltaica; Irradiação.ABSTRACTSolar energy is obtained through photovoltaic solar panels with the function of capturing the sun's energy and transforming it into electrical energy, increasing the generation of solar energy in regions with greater capture of light energy. Thus, the parameters for the generation of photovoltaic solar energy in Acre, Brazil were analyzed. Data on insolation, maximum and minimum temperatures, precipitation and relative humidity were collected at the National Institute of Meteorology, solar irradiation, at the Reference Center for Solar and Wind Energy Sérgio de S. Brito, regions of Vale do Juruá and Vale do Acre, in the period 2015-2020. Analyzes were quantitative, using mean calculation and inclined plane calculation. When comparing the regions, Vale do Acre presented better results for solar energy generation and with an angle with the highest annual daily average of solar irradiation, considering the project of photovoltaic cells in the region. The work shows that Acre has a lot of insolation and solar irradiation, indicating a high potential for generating solar energy for the regional regions of the state.Keywords: Photovoltaic Efficiency; Solar Radiation; Photovoltaic Cell Temperature; Irradiation.RESUMENLa energía solar se obtiene a través de paneles solares fotovoltaicos con la función de captar la energía del sol y transformarla en energía eléctrica, aumentando la generación de energía solar en las regiones con mayor captación de energía luminosa. Así, se analizaron los parámetros para la generación de energía solar fotovoltaica en Acre, Brasil. Los datos sobre insolación, temperaturas máximas y mínimas, precipitación y humedad relativa fueron recolectados en el Instituto Nacional de Meteorología, irradiación solar, en el Centro de Referencia de Energía Solar y Eólica Sérgio de S. Brito, regiones de Vale do Juruá y Vale do Acre, en el período 2015-2020. Los análisis fueron cuantitativos, utilizando cálculo de medias y cálculo de plano inclinado. Al comparar las regiones, Vale do Acre presentó mejores resultados para la generación de energía solar y con un ángulo con el promedio diario anual más alto de irradiación solar, considerando el diseño de células fotovoltaicas en la región. El trabajo muestra que Acre tiene mucha insolación e irradiación solar, lo que indica un alto potencial de generación de energía solar para las regiones regionales del estado.Palabras clave: Eficiencia Fotovoltaica; Radiación Solar; Temperatura de la Celda Fotovoltaica; Irradiación.


2013 ◽  
Vol 64 (4) ◽  
Author(s):  
Hadi Nabipour Afrouzi ◽  
Saeed Vahabi Mashak ◽  
Zulkurnain Abdul-Malek ◽  
Kamyar Mehranzamir ◽  
Behnam Salimi

Renewable energy plays an important role in the national energy policy especially in reducing greenhouse gas emissions. For a photovoltaic (PV) system, one important consideration is the cost of the system. One needs to select the best PV array from a range of selection, that is, the one which is the most efficient and with a best price. This article illustrates a method to compute the size and cost of a required PV array, and then after to compute the required battery for the case of a photovoltaic building in Malaysia. The computation is simulated using Matlab integrated with suitable mathematical equations. The generated current and power of the PV array are calculated for daily solar irradiation in Malaysia. The computation enables the user to quickly compute the initial cost needed to be spent if a given PV system is to be installed. A typical building requiring 12 kWh daily energy with 6 kW peak demand load was shown to need at least 114 solar modules at a cost of about RM53k. It is noted that the main cost of the whole PV system is mainly contributed by the cost of the chosen PV array. Hence, the right choice of a PV module is vital in achieving the minimum cost.


2020 ◽  
Vol 26 (4) ◽  
pp. 21-32
Author(s):  
Nibras Mahmood Obaid ◽  
Emad T. Hashim ◽  
Naseer K. Kasim

The performance analyses of 15 kWp (kW peak) Grid -Tied solar PV system (that considered first of its type) implemented at the Training and Energy Research Center Subsidiary of Iraqi Ministry of Electricity in Baghdad city has been achieved. The system consists of 72 modules arranged in 6 strings were each string contains 12 modules connected in series to increase the voltage output while these strings connected in parallel to increase the current output. According to the observed duration, the reference daily yields, array daily yields and final daily yields of this system were (5.9, 4.56, 4.4) kWh/kWp/day respectively. The energy yield was 1585 kWh/kWp/year while the annual total solar irradiation received by solar array system was 1986.4kWh/m2. The average power losses per day of array, system losses and overall losses were (1.38, 0.15, 1.53) kWh/kWp/day respectively. The average capacity factor and performance ratio per year were 18.4% and 75.5% respectively. These results highlighted the performance analyses of this PV solar system located in Baghdad city. The performance can be considered as good and significant comparing with other world PV solar stations.  


Author(s):  
Ashish Grover ◽  
Anita Khosla ◽  
Dheeraj Joshi

<p>This   paper deeply explains the analysis through simulation and sizing of grid connected photovoltaic plant of 20MW for the site Devdurga, Karnataka India with use of PV syst software tool. Primarily, the trajectories the behavior of grid tied photovoltaic system at a particular location. It gives results for the geographical position taken by maps for avoiding the oversizing or under sizing of the systems which projects the installation with very much realistic conditions. The projected area is of about 110 acres would generate 44854 MWh/year for a 20MW PV system, with a performance ratio of 76.28%.Loss fraction taken for simulation and sizing is 2%.The paper also includes the study and behavior of the system   with tilt and orientation of the PV Panel which gives better simulation results at similar latitudes for any feasible sizing.</p>


Author(s):  
Mahmoud Ismail

Performance ratio is one of the indicators used to describe the effectiveness of the PV systems. The sustainability of the PV system year after year as well as its reliability can be checked by measuring the performance ratio each year. This indicator will also enable us to carry out a comparison between the performances of different PV systems. In this paper, the performance ratios for five PV systems installed on the roof tops of some of PTUK university buildings have been calculated on monthly and yearly basis. The analysis has been carried out using the available data (energy production and solar irradiation) for the year 2019. It was found that the performance ratio has higher values for May and September in comparison with other months. On the other hand, its lowest values were obtained in winter months. This trend can be observed for all of the PV clusters on the five buildings.  When taking into account the overall system, the highest value for the performance ratio was 0.89, which was for September, whereas its lowest value of 0.70 was obtained in January. The performance ratio, which was calculated on yearly basis for the overall system, was found to be 0.80. When considering each building separately, the lowest value was 0.44 for the “Services” building whereas the highest value was 0.94 for the Science building.


2021 ◽  
Vol 13 (14) ◽  
pp. 7680
Author(s):  
Ghoname Abdullah ◽  
Hidekazu Nishimura

In this paper, the grid-connected photovoltaic system in Tochigi prefecture, Japan, is presented, and its technical and economic performance after eight years is evaluated. The system has a peak power of 40.1 kWp and has been in operation since 2012. The entire electricity generated by the system was fed into the state grid. The system is suitably monitored for one year (2019) and analyzed using the parameters developed and defined in the standard IEC 61724-1 by the International Electrotechnical Commission. The system’s different parameters included array yield, final yield, capacity utilization factor, and performance ratio of the system. An analytical model with solar irradiation obtained from Power Data Access Viewer was developed to investigate and evaluate the efficiency of the system monthly and annual energy generation by comparing the simulated and measured energy acquired from the inverter. A positive linear relationship is observed between solar irradiation data obtained from Power Data Access Viewer and the grid-connected photovoltaic system energy injected into the utility grid. While an annual total of 48,521 kWh of energy was expected to be generated, 38,071 kWh was generated and injected into the utility in 2019. This study also introduces and explains the mechanism of the Feed-In-Tariff system in Japan. The performance of the grid-connected photovoltaic system under this study was compared with that of other systems installed across the globe.


2017 ◽  
Vol 7 (1) ◽  
pp. 33
Author(s):  
Shubham Tiwari ◽  
Bharti Dwivedi ◽  
M.P Dave

An effort has been made to access what happens to prevailing thermal generation plants if the generation from renewable energy resources is increased above 20% of total generation. A test case has been taken where generation system comprising of ten thermal generating units is in conjunction with a 500 MW Wind Energy generation plant, and a 500 MW Solar Energy generation plant. It has been found that on one hand the cost of generation gets significantly reduced whereas, on the other hand few thermal generators are compelled to remain with no generation at all. The study reveals the peak load shaving and the economy achieved in overall generation system versus the threat to individual thermal generating plant due to inclusion of nearly 23% generation from renewable resources.


2014 ◽  
Vol 27 (2) ◽  
pp. 275-298 ◽  
Author(s):  
Rajendra Singh ◽  
Githin Alapatt ◽  
Guneet Bedi

With the advent of solar panels and windmills, and our ability to generate and use electrical energy locally without the need for long-range transmission, the world is about to witness transformational changes in energy infrastructure. The use of photovoltaics (PV) as source of direct current (DC) power reduces the cost and improves the reliability of PV system. DC microgrid and nanogrid based on PV and storage can provide sustainable electric power to all human beings in equitable fashion. Bulk volume manufacturing of batteries will lead to cost reduction in a manner similar to the cost reduction experience of PV module manufacturing. Future manufacturing innovations and R & D directions are discussed that can further reduce the cost of PV system. If the current trends of PV growth continue, we expect PV electricity cost with storage to reach $0.02 per kWh in the next 8-10 years.


2019 ◽  
Vol 25 ◽  
pp. 1-19
Author(s):  
Sindri Þrastarson ◽  
Björn Marteinsson ◽  
Hrund Ólöf Andradóttir

The efficiency and production costs of solar panels have improved dramatically in the past decades. The Nordic countries have taken steps in instigating photovoltaic (PV) systems into energy production despite limited incoming solar radiation in winter. IKEA installed the first major PV system in Iceland with 65 solar panels with 17.55 kW of production capacity in the summer of 2018. The purpose of this research was to assess the feasibility of PV systems in Reykjavík based on solar irradiation measurements, energy production of a PV array located at IKEA and theory. Results suggests that net irradiation in Reykjavík (64°N, 21° V) was on average about 780 kWh/m2 per year (based on years 2008-2018), highest 140 kWh/m2 in July and lowest 1,8 kWh/m2 in December. Maximum annual solar power is generated by solar panels installed at a 40° fixed angle. PV panels at a lower angle produce more energy during summer. Conversely, higher angles maximize production in the winter. The PV system produced over 12 MWh over a one-year period and annual specific yield was 712 kWh/kW and performance ratio 69% which is about 10% lower than in similar studies in cold climates. That difference can be explained by snow cover, shadow falling on the panels and panels not being fixed at optimal slope. Payback time for the IKEA PV system was calculated 24 years which considers low electricity prices in Reykjavik and unforeseen high installation costs. Solar energy could be a feasible option in the future if production- and installation costs were to decrease and if the solar PV output could be sold to the electric grid in Iceland.


Sign in / Sign up

Export Citation Format

Share Document