scholarly journals Investigation of the Cross-Cutting Polycrystalline Diamond Compact Bit Drilling Efficiency

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Chun-Liang Zhang ◽  
Ying-Xin Yang ◽  
Hai-Tao Ren ◽  
Can Cai ◽  
Yong Liu ◽  
...  
Keyword(s):  
Cutting Force ◽  
Polycrystalline Diamond ◽  
Rock Breaking ◽  
The Novel ◽  
Cutting Efficiency ◽  
Bottom Hole ◽  
Pdc Bit ◽  
The Cross ◽  
Polycrystalline Diamond Compact ◽  
Cutting Modes

The parallel track scraping principle of conventional PDC bits largely limits the cutting efficiency and working life in deep formations. Cross-cutting polycrystalline diamond compact (PDC) bit may be an efficient drilling tool that increases the rock-breaking efficiency through both cross-cutting and alternate-cutting modes of the PDC cutter. The motion track equation of the cross-cutting PDC bit was derived by using the compound coordinate system, and the motion track was analyzed. Meanwhile, through the unit experiment and discrete element simulation, the cutting force, volume-specific load, and crack propagation were analyzed under different cutting modes. Through establishing a nonlinear dynamic model of the bit-rock system, the speed-up mechanism of the novel bit was analyzed based on rock damage, rock stress state, and motion characteristic of the bit during the rock-breaking process. Compared with unidirectional cutting, cross-cutting produces less cutting force, more brittle fracture, and a greater decrease of formation strength. The novel PDC bit can put more rock elements into a tensile stress condition than a conventional PDC bit, and the plastic energy dissipation ratio of the cross-cutting PDC bit is lower while the damage energy consumption ratio is higher than they are for conventional bits, which is beneficial to increasing the ratio of fracture failure and improving rock-breaking efficiency. Laboratory drilling tests show that the cross-cutting PDC bit can create mesh-like bottom-hole features. Drilling contrast experiments show that a mesh-like bottom-hole pattern can be obtained by using the cross-cutting PDC bit, of which the ROP is obviously higher than that of the conventional bit when drilling in sandstone or limestone formation. Meanwhile, the influence of deviation angle, weight on bit, and rock properties on cutting efficiency of the cross-cutting PDC bit are studied.

Kinematic and bottom-hole pattern analysis of a composite drill bit of cross-scraping

2016 ◽  
Vol 231 (17) ◽  
pp. 3104-3117 ◽  
Author(s):  
Yingxin Yang ◽  
Chunliang Zhang ◽  
Lian Chen ◽  
Yong Liu
Keyword(s):  
Polycrystalline Diamond ◽  
Rock Breaking ◽  
Speed Ratio ◽  
Drill Bit ◽  
The Novel ◽  
Analysis Model ◽  
Fracture Failure ◽  
Bottom Hole ◽  
Geometric Relationship ◽  
Polycrystalline Diamond Compact

For improving the drilling efficiency of polycrystalline diamond compact drill bit, a novel polycrystalline diamond compact drill bit is presented with a new rock-breaking method named as cross-scraping. In the novel polycrystalline diamond compact drill bit which is referred to as a composite drill bit, polycrystalline diamond compact cutters are mounted on rotary wheels as major cutting elements, and as a result, mesh-like scraping tracks are formed in the outer radial area of the bottom-hole. Rock-breaking method of the composite drill bit causes both shearing and fracture failure of the bottom-hole rock, which will greatly increase the rock-breaking efficiency and will prolong the bit service life. By analyzing the complex motion of cutters on the composite drill bit, velocity and acceleration models of the cutters, as well as wheel/bit speed ratio model of the bit are established in accordance with the geometric relationship between cutters and bit body in a compound coordinate system. In simulation examples, motion tracks, velocity and acceleration features of the cutter and especially the bottom-hole pattern are analyzed. Further, indoor experiments are conducted to test the mesh-like bottom-hole pattern and rock-breaking features, which have proved the accuracy of the analysis model of the composite drill bit.

scholarly journals Simulation and Experimental Study of the Rock Breaking Mechanism of Personalized Polycrystalline Diamond Compact Bits

2020 ◽  
Vol 13 (5) ◽  
pp. 122-131
Author(s):  
Yu Jinping ◽  
◽  
Zou Deyong ◽  
Sun Yuanxiu ◽  
Zhang Yin
Keyword(s):  
Experimental Study ◽  
Finite Element ◽  
Tensile Stress ◽  
Crack Propagation ◽  
Tangential Force ◽  
Polycrystalline Diamond ◽  
Rock Breaking ◽  
Pdc Bit ◽  
Breaking Mechanism ◽  
Polycrystalline Diamond Compact

Rock breaking is a complex physical process that can be influenced by various factors, such as geometrical shape and cutting angle of rock breaking tools. Experimental study of the rock breaking mechanism of personalized bits is restricted due to long cycle and high cost. This study simulated the rock breaking mechanism of polycrystalline diamond compact (PDC) bit by combining finite element method and experiment. The simulation was performed to shorten the period and reduce the cost of studying the rock breaking mechanism of PDC bits. A rock breaking finite element model for sting cutters of personalized PDC bit was established to simulate the rock breaking process. The crack propagation pattern, dynamic stress of rock breaking, and rock breaking mechanism of sting cutters of personalized PDC bit were analyzed. The correctness of the simulation results was verified through experiments. Results demonstrate that the rock breaking load increases with the crack propagation in the fracture initiation and propagation stages, with the maximum tangential force of 1062.5 N and maximum axial force of 1850.0 N. The load changes in a small range when the crack penetrates the rock, with the tangential force of 125.0–500.0 N and axial force of 375.0–875.0 N. The rock breaking mechanism of the sting cutters of bit is consistent with maximum tensile stress theory. The rock begins to break when the tensile stress of rock is 36.9 MPa. The sting cutters of personalized PDC bit have better wear resistance than the sting cutters of conventional bit. The average wear rates of personalized PDC and conventional bits are 1.74E-4 and 2.1E-4 mm/m, respectively. This study serves as reference for shortening the study period of rock breaking mechanism, efficiently designing personalized PDC bit structure, reducing bit wear, and enhancing rock breaking efficiency.

Mathematical Modeling of PDC Bit Drilling Process Based on a Single-Cutter Mechanics

1993 ◽  
Vol 115 (4) ◽  
pp. 247-256 ◽  
Author(s):  
A. K. Wojtanowicz ◽  
E. Kuru
Keyword(s):  
Polycrystalline Diamond ◽  
Rock Properties ◽  
Drilling Process ◽  
Drilling Parameters ◽  
Pdc Bit ◽  
Analytical Development ◽  
Assumed Similarity ◽  
Balance Of Forces ◽  
Bit Life ◽  
Polycrystalline Diamond Compact

An analytical development of a new mechanistic drilling model for polycrystalline diamond compact (PDC) bits is presented. The derivation accounts for static balance of forces acting on a single PDC cutter and is based on assumed similarity between bit and cutter. The model is fully explicit with physical meanings given to all constants and functions. Three equations constitute the mathematical model: torque, drilling rate, and bit life. The equations comprise cutter’s geometry, rock properties drilling parameters, and four empirical constants. The constants are used to match the model to a PDC drilling process. Also presented are qualitative and predictive verifications of the model. Qualitative verification shows that the model’s response to drilling process variables is similar to the behavior of full-size PDC bits. However, accuracy of the model’s predictions of PDC bit performance is limited primarily by imprecision of bit-dull evaluation. The verification study is based upon the reported laboratory drilling and field drilling tests as well as field data collected by the authors.

Issues in Polycrystalline Diamond Compact Cutter–Rock Interaction From a Metal Machining Point of View—Part II: Bit Performance and Rock Cutting Mechanics

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Demeng Che ◽  
Peidong Han ◽  
Ping Guo ◽  
Kornel Ehmann
Keyword(s):  
Metal Cutting ◽  
Polycrystalline Diamond ◽  
Rock Cutting ◽  
Point Of View ◽  
Rock Interaction ◽  
Metal Machining ◽  
Pdc Bit ◽  
Rock Cutting Mechanics ◽  
Cutting Processes ◽  
Polycrystalline Diamond Compact

In Part I of this paper, the issues related to temperature, stress and force were reviewed and parallels were drawn between both metal machining and rock cutting. Part II discusses the issues more directly related to polycrystalline diamond compact (PDC) bit performance and rock mechanics. However, relevant issues in various metal cutting processes will continue to be presented to clarify the gaps and similarities between these two classes of processes.

First Application of Hybrid Bit Technology to Optimize Drilling Through S Shape Directional Section with High Chert Content in UAE Land Operations

2021 ◽  
Author(s):  
Ygnacio Jesus Nunez ◽  
Munir Bashir ◽  
Fernando Ruiz ◽  
Rakesh Kumar ◽  
Mohamed Sameer ◽  
...  
Keyword(s):  
Good Condition ◽  
Polycrystalline Diamond ◽  
Steering System ◽  
Directional Drilling ◽  
Main Challenge ◽  
Drilling Parameters ◽  
Pdc Bit ◽  
Heterogeneous Formation ◽  
Polycrystalline Diamond Compact ◽  
Cutting Mechanisms

Abstract This paper highlights the solution, execution, and evaluation of the first 12.25″ application of hybrid bit on rotary steerable system in S-Shape directional application to drill interbedded formations with up to 25 % chert content in UAE land operations. The main challenge that the solution overcame is to drill through the hard chert layers while avoiding trips due to PDC bit damage nor drilling hour's limitation of TCI bit while improving the overall ROP and achieving the directional requirement. The solution package has demonstrated a superior ROP over rollercone bits, as well as improved PDC cutter durability and lower reactive torque leading to better steerability and stability which will be detailed in this paper. A significant contributor to such success was utilizing a new hybrid bit technology which incorporates the dual cutting mechanisms of both polycrystalline Diamond Compact (PDC) and rollercone bits. This allows a more efficient drilling by bringing the durability of the crushing action of rollercone to drill through hard interbedded lithology and the effectiveness of the shearing action of PDC cutters to improve ROP without sacrificing the toughness of the cutting structure edge. The proposed solution in combined with continues proportional rotary steering system managed to drill 4,670 ft through heterogeneous formation with chert nodules, with an average ROP of 38.29 ft\hr improving ROP by 15% and eliminating extra trips of utilizing roller cone bits to be able to drill though the chert nodules and avoid the PDC bit damage. Leading reduction in cost per foot by 35 %. Additionally, the hybrid bit exceed the expectation achieving 878 thousand of revolutions, with effective bearing and with the drilling cutting structure in a very good condition. Furthermore, the directional objectives were met with high quality directional drilling avoiding wellbore tortuosity. Such success was established through application analysis, specific formations drilling roadmaps and optimized drilling parameters in order to improve the overall run efficiency. The combination of roller cone and PDC elements in a hybrid bit designed to deliver better efficiency and torque stability significantly increased performance drilling the section in one single run, proven that heterogeneous formations can be drill.

Hybrid Physics-Field Data Approach Improves Prediction of ROP / Drilling Performance of Sharp and Worn PDC Bits

2021 ◽  
Author(s):  
Guodong David Zhan ◽  
Arturo Magana-Mora ◽  
Eric Moellendick ◽  
John Bomidi ◽  
Xu Huang ◽  
...  
Keyword(s):  
Prediction Models ◽  
Collaborative Study ◽  
Hybrid Approach ◽  
Polycrystalline Diamond ◽  
Rock Properties ◽  
Quantitative Prediction ◽  
Model Learning ◽  
Drilling Performance ◽  
Pdc Bit ◽  
Polycrystalline Diamond Compact

Abstract This study presents a hybrid approach that combines data-driven and physics models for worn and sharp drilling simulation of polycrystalline diamond compact (PDC) bit designs and field learning from limited downhole drilling data, worn state measurements, formation properties, and operating environment. The physics models include a drilling response model for cutting forces, worn or rubbing elements in the bit design. Decades of pressurized drilling and cutting experiments validated these models and constrained the physical behaviour while some coefficients are open for field model learning. This hybrid approach of drilling physics with data learning extends the laboratory results to application in the field. The field learning process included selecting runs in a well for which rock properties model was built. Downhole drilling measurements, known sharp bit design, and measured wear geometry were used for verification. The models derived from this collaborative study resulted in improved worn bit drilling response understanding, and quantitative prediction models, which are foundational frameworks for drilling and economics optimization.

Fragmentation Characteristics of Rocks Under Indentation by a Single Polycrystalline Diamond Compact Cutter

2021 ◽  
Vol 143 (10) ◽  
Author(s):  
Zhaosheng Ji ◽  
Huaizhong Shi ◽  
Xianwei Dai ◽  
Hengyu Song ◽  
Gensheng Li ◽  
...  
Keyword(s):  
Contact Force ◽  
Brittle Failure ◽  
Failure Modes ◽  
Polycrystalline Diamond ◽  
Rake Angle ◽  
Von Mises Stress ◽  
Rock Interaction ◽  
Initiation Point ◽  
Pdc Bit ◽  
Polycrystalline Diamond Compact

Abstract Polycrystalline diamond compact (PDC) bit accounts for the most drilling footage in the development of deep and geothermal resources. The goal of this paper is to investigate the PDC cutter-rock interaction and reveal the rock fragmentation mechanism. A series of loading and unloading tests are conducted to obtain the curves of contact force versus penetration displacement. A single practical PDC cutter is fixed on the designed clamping devices that are mounted on the servo experiment system TAW-1000 in the tests. The craters morphology and quantified data were obtained by scanning the fragmented rock specimen using a three-dimensional morphology scanner. Finally, a numerical model is established to get the stress and deformation fields of the rock under a single PDC cutter. The results show that there are two kinds of failure modes, i.e., brittle failure and plastic failure, in the loading process. Marble is more prone to brittle fracture and has the lowest specific energy, followed by shale and granite. The brittle failure in marble mainly occurs behind the cutter while that happens ahead of the cutter for shale. Curves of contact force versus penetration displacement illustrate that a cutter with a back rake angle of 40 deg has a better penetration result than that with a back rake angle of 30 deg. Enhancing loading speed has a positive effect on brittle fragmentation. The distribution of von Mises stress indicates the initiation point and direction, which has a good agreement with the experiment. The research is of great significance for optimizing the PDC bit design and increasing the rate of penetration.

The wear analysis model and rock-breaking mechanism of a new embedded polycrystalline diamond compact

2016 ◽  
Vol 231 (22) ◽  
pp. 4241-4249 ◽  
Author(s):  
Jialin Tian ◽  
Gang Liu ◽  
Lin Yang ◽  
Chunming Wu ◽  
Zhi Yang ◽  
...  
Keyword(s):  
Wear Mechanism ◽  
Polycrystalline Diamond ◽  
Rock Breaking ◽  
Rapid Decline ◽  
Analysis Model ◽  
Diamond Layer ◽  
Gas Drilling ◽  
Wear Analysis ◽  
Carbide Matrix ◽  
Polycrystalline Diamond Compact

Polycrystalline diamond layer peel-off is a hot topic in oil and gas drilling engineering. When an integrated polycrystalline diamond compact cutter suffers overload, there is a rapid decline in its rock-breaking performance and drilling rate of penetration. To modify the comprehensive performance of polycrystalline diamond compact, we innovatively propose a new embedded polycrystalline diamond compact. According to geometric analysis theory combined with the linear combination rule, the three typical embedded design schemes – the imitation palm-shaped, imitation Z-shaped and ring-embedded designs – are discussed. The influences of the number, size, location and combination of the embedded polycrystalline diamond layer on the polycrystalline diamond compact wear mechanism and rock-breaking performance are analysed. The results show that the embedded element and carbide matrix are combined by brazing welding, which not only exerts high abrasion resistance on the polycrystalline diamond layer but also combines with the good impact performance of carbide matrix. Compared with ordinary polycrystalline diamond compact, the intake amount of a single-embedded polycrystalline diamond compact is smaller, and it wears more evenly during the rock-breaking process. Comparing the results from before and after drilling, it effectively prevents the ordinary polycrystalline diamond compact from easily peeling off when suffering overload. The unique wear analysis model can be applied to other types of polycrystalline diamond compact by adjusting the embedding method. The research conclusions provide useful insights into the study of the polycrystalline diamond compact wear mechanism and rock-breaking performance.

scholarly journals Analysis of Rock Dynamic Stresses During the Drilling by Polycrystalline Diamond Compact Bits

2020 ◽  
Vol 19 (4) ◽  
pp. 607-618
Author(s):  
J. P. Yu ◽  
D. Y. Zou ◽  
Y. Zhang
Keyword(s):  
Axial Force ◽  
Dynamic Stress ◽  
Tangential Force ◽  
Polycrystalline Diamond ◽  
Rock Breaking ◽  
The Finite Element Method ◽  
Principal Stresses ◽  
Dynamic Stresses ◽  
Polycrystalline Diamond Compact ◽  
Initial Rock

In view of shortening the development period of polycrystalline diamond compact (PDC) bits, the finite element method was adopted to simulate the dynamic stress of rocks. By employing drilling related theories, the three dynamic principal stresses of rock were analysed and the dynamic rock-breaking criterion was established. Second, the drilling model of PDC core bit was constructed, and the stress was simulated and calculated. Finally, laboratory tests were carried out to verify the simulation results. The analytical results demonstrate that the two obvious stages in the rock-breaking process are the initial rock-breaking stage and the normal one. The dynamic rock-breaking stress in the normal drilling stage varies from 66.3 to 99.6 MPa, which is lower than 278.4 MPa in the initial rock-breaking stage. During spud drilling, the axial force and the tangential force are 1.85 and 1.60 kN, respectively. During normal drilling, the axial force ranges from 0.2 to 0.9 kN, and the tangential force from 0.15 to 0.6 kN. The load of normal drilling is lower than the spudding load, and the bit is more likely to be damaged during spudding. The bit is normally worn during normal drilling.

Study on Composite Design Suitable for High Hardness and Strong Abrasive Formation

2021 ◽  
Vol 8 ◽  
pp. 41-49
Author(s):  
Dongdong Song ◽  
Yingxin Yang ◽  
Haitao Ren
Keyword(s):  
Service Life ◽  
Stress Field ◽  
Impact Load ◽  
Polycrystalline Diamond ◽  
High Hardness ◽  
Rock Breaking ◽  
Drilling Process ◽  
Wear And Tear ◽  
Thermal Wear ◽  
Polycrystalline Diamond Compact

PDC (Polycrystalline Diamond Compact bit) composite is the most important cutting element of petroleum bit, which performance directly affects the service effect and service life of the bit. During the drilling process, the cutter will produce a large amount of friction heat when cutting the rock, resulting in a sharp increase in the internal temperature of the cutter. When the temperature reaches a certain value, thermal wear and tear are very easy to occur, which will not only cause diamond delamination but also reduce the wear resistance of the cutter. Under the action of impact load, impact failure is more likely to occur, which greatly reduces the service life of the cutter and the rock-breaking efficiency of the drill bit. Therefore, this paper studies the composite interface suitable for high-temperature drilling through the changes of cutting tooth temperature field and stress field with different interface shapes, which shows that the non-planar interface is more suitable for improving the cutting tooth life of composite under the action of comprehensive stress field.

Sign in / Sign up

Export Citation Format

Share Document