Mechanical characterization of polylactic acid reinforced bagasse/basalt hybrid fiber composites

2018 ◽  
Vol 53 (1) ◽  
pp. 33-43 ◽  
Author(s):  
Francis L King ◽  
A Arul Jeya Kumar ◽  
Srinivasan Vijayaragahavan
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Water Absorption ◽  
Polylactic Acid ◽  
Fiber Composite ◽  
Basalt Fiber ◽  
Fiber Content ◽  
Interfacial Bonding ◽  
Weight Percentage ◽  
Bagasse Fiber

This paper focuses on the mechanical behavior of Polylatic acid reinforced Basalt and Bagasse fibers. The most important aspect in formulating this hybrid composite with better mechanical properties is the optimization of interfacial bonding between the reinforcing bagasse fiber and basalt fiber and polymer matrix. The composite of different weight proportion of the materials is compounded using twin screw extruder. The specimens were prepared by injection molding and subjected to various mechanical testing under tensile, flexural, and impact loads. It was found that 84 wt% of polylactic acid, 12 wt% of Basalt fiber and 4 wt% of Bagasse fiber composite exhibits better mechanical properties compared to other composites taken for study in this research. The better tensile, flexural, and impact strength of 52.8 MPa, 82.2 MPa, and 3.39 KJ/m2 were observed. The results show that the fiber content in weight percentage is playing a major than the fiber length on the improvement of tensile, flexural, and impact properties. The mechanical behavior obtained through experiments witnessed that Bagasse/Basalt fiber reinforcement in polylactic acid composites can be used as medium-load applications because of its low cost and ease of decomposability. The scanning electron microscope photography of the tested specimens shows better interfacial bonding between matrix and fibers. Also, the water absorption test indicates increase in fiber content increases the water absorption rate, reveals good degradation property of the composite. Additionally, the use of Bagasse fiber promotes the degradation of the material after its life time.

Mechanical and Morphological Properties of Poly(Lactic Acid)/Bagasse Fiber Composite Foams

2016 ◽  
Vol 851 ◽  
pp. 31-36 ◽  
Author(s):  
Tarinee Nampitch ◽  
Chanon Wiphanurat ◽  
Thiti Kaisone ◽  
Pran Hanthanon
Keyword(s):  
Mechanical Properties ◽  
Fiber Composite ◽  
Sem Analysis ◽  
Fiber Content ◽  
Morphological Properties ◽  
Poly Lactic Acid ◽  
Foaming Agent ◽  
Composite Foams ◽  
Bagasse Fiber ◽  
Composite Properties

This research attempted to prepare composite foams of PLA/bagasse fiber with various fiber content at 0, 5, 10, 15, 20 wt% and a fixed foaming agent with extra added 2 wt% for all composites. The mechanical properties and morphology of neat PLA and PLA/bagasse fiber composite foams were investigated. The tensile strength showed that the highest fiber content of 7 wt% was 45.27 MPa, while neat PLA was 25.63 MPa. Impact strength showed a decreasing trend with increasing fiber content. SEM analysis was important to reveal the phase of fiber and matrix for support to discuss the results trend of PLA and composite properties.

Fabrication and Experimental Testing of Hybrid Composite Material Having Biodegradable Bagasse Fiber in a Modified Epoxy Resin: Evaluation of Mechanical and Morphological Behavior

2021 ◽  
Author(s):  
Vaishally Dogra ◽  
Chandra Kishore ◽  
Akarsh Verma ◽  
Amit Kumar Rana ◽  
Amit Gaur
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Water Absorption ◽  
Natural Fiber ◽  
Experimental Testing ◽  
Matrix Material ◽  
Research Work ◽  
Absorption Capacity ◽  
Weight Percentage ◽  
Bagasse Fiber

Natural fibers such as bagasse, jute, sisal and coir are biodegradable as well as non-toxic in nature, so the use of natural fiber is safe. Bagasse contains about 50% cellulose, 25% hemicellulose, and 25% lignin. The present work has been undertaken to develop a composite using bagasse fiber as reinforcement and to study its mechanical properties, morphology, water absorption capacity and performance. The composites were prepared with different weight percentage of bagasse fiber by hand lay-up method. In the present research work, it can be concluded that with increase in wt.% of bagasse fiber in matrix material the rate of water absorption increases. Ultimate tensile strength, ultimate compressive and flexural strength of the composite are less than the pure epoxy while Young’s modulus is higher for composite. Ultimate tensile, ultimate compressive strength and flexural strength of composite is decreasing at all cross head speed with increase in wt.% of bagasse fiber while flexural strain is increasing. Scanning Electron Microscopy (SEM) showed that for 5 wt.% of bagasse fiber the binding between epoxy and bagasse fiber is better than the 10 and 15 wt.% of bagasse fiber configuration. This was because of the increase in wt.% of bagasse fiber, which results in cavities and improper binding in the composite domain. Thus, as we increase the wt.% of bagasse fiber it causes the decrease in mechanical properties of composite.

Preparation of ZrO2 Composite Ceramics with High Thermal Shock Resistance

2012 ◽  
Vol 455-456 ◽  
pp. 650-654 ◽  
Author(s):  
He Yi Ge ◽  
Jian Ye Liu ◽  
Xian Qin Hou ◽  
Dong Zhi Wang
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Thermal Shock ◽  
Thermal Shock Resistance ◽  
Sintering Temperature ◽  
Fiber Composite ◽  
Physical And Mechanical Properties ◽  
Composite Ceramics ◽  
Shock Resistance ◽  
Absorption Measurements

The physical and mechanical properties of nanometer ZrO2-ZrO2fiber composite ceramics were studied by introduction of ZrO2fiber. ZrO2composite ceramics at different sintering temperature was investigated by porosity and water absorption measurements, flexual strength and thermal shock resistance analysis. Results showed that ZrO2composite ceramics containing 15 wt% ZrO2fiber with sintering temperature of 1650°C exhibited good mechanical properties and thermal shock resistance. The porosity and the water absorption were 8.84% and 1.62%, respectively. The flexual strength was 975 MPa and the thermal shock times reached 31 times. Scanning electron microscope (SEM) was used to analyze the microstructure of ZrO2composite ceramics.

Hybridization effect on mechanical properties of short basalt/jute fiber-reinforced polyester composites

2013 ◽  
Vol 20 (4) ◽  
pp. 343-350 ◽  
Author(s):  
Pandian Amuthakkannan ◽  
Vairavan Manikandan ◽  
Jebbas Thangaiah Winowlin Jappes ◽  
Marimuthu Uthayakumar
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Hybrid Composites ◽  
Fiber Composite ◽  
Testing Machine ◽  
Basalt Fiber ◽  
Jute Fiber ◽  
Computer Assisted ◽  
Fiber Reinforced ◽  
Polyester Composites

AbstractMechanical properties of fiber reinforcement that can be obtained by the introduction of basalt fibers in jute fiber-reinforced polyester composites have been analyzed experimentally. Basalt/jute fiber-reinforced hybrid polymer composites were fabricated with a varying fiber percentage by using compression molding techniques. The fabricated composite plates were subjected to mechanical testing to estimate tensile strength, flexural strength and impact strength of the composites. The effect of fiber content on basalt/jute fiber in the composites has been studied. Addition of jute fiber into basalt fiber composite makes it a cost-effective one. Incorporation of basalt fiber into the composites was at approximately 10%, 20%, up to 90%, and the jute fiber percentage was reduced from 90%, 80%, to 10% correspondingly. Mechanical properties were investigated as per ASTM standards. Tensile and flexural strengths were tested by using a computer-assisted universal testing machine, and impact strength by using an Izod impact tester. It has been observed that the addition of jute fiber to the basalt fiber polyester composites enhanced the mechanical properties. Water absorption of hybrid composites was also analyzed and was found to be proportional to fiber percentage.

scholarly journals Thermal and Mechanical properties of epoxy-jute fiber composite

2014 ◽  
Vol 27 (2) ◽  
pp. 77-82 ◽  
Author(s):  
H Ahmad ◽  
MA Islam ◽  
MF Uddin
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Fiber Length ◽  
Epoxy Composite ◽  
Fiber Composite ◽  
Young Modulus ◽  
Fiber Content ◽  
Jute Fiber ◽  
Elongation At Break

Chopped jute fiber-epoxy composites with varying fiber length (2-12 mm) and mass fraction (0.05-0.35) had been prepared by a heat press unit. The cross-linked product was characterized in terms of specific gravity, thermal conductivity, tensile strength, Young modulus and elongation at break. The transverse thermal conductivities for randomly oriented fibers in the composite were investigated by Lees and Charlton’s method. The tensile strength, Young modulus and elongation at break were investigated by a Universal Tensile Tester. With an increase in the fiber content (irrespective of the fiber length), the thermal conductivity of the composite decreases; the decreasing rate being highest for the fiber length of 2 mm followed by that for the fiber length of 6 and 12 mm. The decreasing rate of the thermal conductivity of the jute-epoxy composite is comparatively higher to that reported in literature for acrylic polymer hemp fiber composite. The tensile strength also decreases with the increase of the fiber content in the composite. The fiber length does not show to have significant effect on the tensile strength of the composite; the variation in strength being masked within experimental error. The Young modulus increases with the increase of fiber content within elastic limit; showing the highest values for the fiber length of 6 mm followed by those for the fiber length of 2 mm and 12 mm. The elongation at break shows slightly increasing trend up to 15% fiber content, but beyond that it decreases drastically. The specific gravity decreases with the increase in the fiber content and thus the recalculated specific tensile strength is found to keep at a stable level of 36MPa up to the fiber content of 20%, and beyond that the specific tensile strength decreases with the increase in the fiber content. It is concluded that jute fiber-epoxy composite could be used as a good heat-insulating material. Further investigation is recommended on the improvement of the thermal insulation keeping the mechanical properties unchanged or even improved. The TGA study is also required to ascertain the field of application of the material. DOI: http://dx.doi.org/10.3329/jce.v27i2.17807 Journal of Chemical Engineering, IEB Vol. ChE. 27, No. 2, December 2012: 77-82

Mechanical Properties of P34HB/PLA Binary Blendsafter Thermal-Oxidative and Hydrothermal Aging

2013 ◽  
Vol 647 ◽  
pp. 798-801 ◽  
Author(s):  
Wen Can Xi ◽  
Hong Mei Kang ◽  
Hua Li ◽  
He Zhou Liu ◽  
Wei Jie Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Mechanical Behavior ◽  
Poly Lactic Acid ◽  
Hydrothermal Aging ◽  
Weight Percentage ◽  
Lower Ratio

Binary blendscomposed of polyhrdroxyalkanoates (P34HB) and poly(lactic acid) (PLA) with various P34HB weight percentage were preparedby extrusion and compressing molding.Both the thermo-oxidative agingat 80°Cand the hydrothermal aging at 80°C with 80% humidity were performed for 300 h for the P34HB/PLA blends respectively.The mechanical properties of tensile strength and elongation-at-breakrevealed that P34HB/PLA blends possessedthe balanced mechanical properties between P34HB and PLA,theblends with higher ratio of P34HBshowed thedeteriorative mechanical behavior in the aging environment faster than thoseblends with lower ratio of P34HB.

scholarly journals Effect of Mix Proportion Parameters on Behaviors of Basalt Fiber RPC Based on Box-Behnken Model

2019 ◽  
Vol 9 (10) ◽  
pp. 2031 ◽  
Author(s):  
Hanbing Liu ◽  
Shiqi Liu ◽  
Shurong Wang ◽  
Xin Gao ◽  
Yafeng Gong
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Basalt Fiber ◽  
Fiber Content ◽  
Reactive Powder Concrete ◽  
Basalt Fibers ◽  
Factors Affecting ◽  
Remarkable Effect ◽  
Mix Proportion ◽  
Reactive Powder

Basalt fibers are widely used in the modification of concrete materials due to its excellent mechanical properties and corrosion resistance. In this study, the basalt fibers were used to modify reactive powder concrete (RPC). The effect of four mix proportion parameters on the working and mechanical properties of basalt fiber reactive powder concrete (BFRPC) was evaluated by the response surface methodology (RSM). The fluidity, flexural and compressive strength were tested and evaluated. A statistically experimental model indicated that D (the silica fume to cement ratio) was the key of interactions between factors, affecting other factors and controlling properties of BFRPC. The increase in basalt fiber content had a remarkable effect on increasing the flexural and compressive strength when D = 0.2. The addition of basalt fiber obviously improved the mechanical properties of RPC. While when D = 0.4, the decrease of fiber content and the increase of quartz sand content could increase the compressive strength.

Investigation on mechanical properties and failure mechanisms of basalt fiber reinforced aluminum matrix composites under different loading conditions

2017 ◽  
Vol 52 (14) ◽  
pp. 1907-1914 ◽  
Author(s):  
Yang Zhiming ◽  
Liu Jinxu ◽  
Feng Xinya ◽  
Li Shukui ◽  
Xu Yuxin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Failure Mechanisms ◽  
Basalt Fiber ◽  
Aluminum Matrix ◽  
Fiber Content ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Fiber Reinforced ◽  
Basalt Fibers ◽  
Static Compression

Basalt fiber reinforced aluminum matrix composites with different fiber contents (i.e. 0 wt%, 10 wt%, 30 wt% and 50 wt%) were prepared by hot-press sintering. Microstructure analysis indicates that basalt fibers are uniformly distributed in 10% basalt fiber reinforced aluminum matrix composite. The interfacial bonding between basalt fibers and aluminum matrix is good, and there is no interface reaction between basalt fiber and aluminum matrix. Quasi-static tensile, quasi-static compression and dynamic compression properties of basalt fiber reinforced aluminum composites were studied, and the influences of basalt fiber content on mechanical properties were discussed. Meanwhile, the failure mechanisms of basalt fiber reinforced aluminum matrix composites with different fiber content were analyzed.

The Effects of Bagasse Fiber Loading on the Mechanical Properties of Skim NR–Clay Nanocomposites

2016 ◽  
Vol 835 ◽  
pp. 42-49
Author(s):  
Tarinee Nampitch ◽  
Rathanawan Magaraphan
Keyword(s):  
Mechanical Properties ◽  
Fatigue Testing ◽  
Fiber Content ◽  
Clay Nanocomposites ◽  
Fiber Loading ◽  
Cloisite 30B ◽  
Cure Time ◽  
Renewable Material ◽  
Bagasse Fiber ◽  
Cloisite 20A

Skim natural rubber (NR)–clay nanocomposites were prepared by a coagulation method using the organoclays Cloisite 15A, Cloisite 20A and Cloisite 30B. This work investigated the use of bagasse fiber developed from locally sourced and renewable material as an alternative and/or secondary filler in skim NR–clay nanocomposites. Bagasse fiber loading in the nanocomposites was 0, 5, 10 and 20 phr; the effects of fiber content on cure characteristics and mechanical properties were then determined. The results suggest that the Mooney viscosity tended to increase with increasing fiber content, whereas the cure time at 90% and fatigue testing score decreased as fiber loading increased.

Sign in / Sign up

Export Citation Format

Share Document