scholarly journals Study of novel solar assisted heating system

2021 ◽  
pp. 014362442110086
Author(s):  
Gareth Davies ◽  
John Blower ◽  
Richard Hall ◽  
Graeme Maidment
Keyword(s):  
Heat Pump ◽  
Solar Collector ◽  
Computer Modelling ◽  
Low Cost ◽  
Cost Savings ◽  
Ambient Air ◽  
Heat Pumps ◽  
Heating Systems ◽  
Collector Plate ◽  
Wide Range

The potential for energy, carbon dioxide equivalent (CO2e) and cost savings when using low emissivity (low-ε) transpired solar collectors (TSCs), combined with heat pumps in a range of configurations, has been investigated using computer modelling. Low-ε TSCs consist of metal solar collector plates with a spectrally sensitive surface, perforated with holes. Ambient air is drawn through the holes and heated by convection from the solar collector plate, increasing the air temperature by up to 25 K. The heated air can be used for e.g. space heating, or pre-heating water in buildings. The models developed have been used to compare the performance of low-ε TSC/heat pump heating systems in small and large buildings, at a range of locations. The model results showed savings in energy, CO2e and costs of up to 16.4% when using low-ε TSCs combined with an exhaust air heat pump compared with using the exhaust air heat pump alone. Practical application: If the UK is to meet its target of reaching net zero greenhouse gas emissions by 2050, it will be necessary to adopt low or zero carbon heating technologies. The novel low emissivity transpired solar collector device investigated can contribute to this. Its advantages include: (i) utilising solar radiation; (ii) readily integrated with existing heating systems e.g. heat pumps; (iii) significant energy, CO2e emissions and cost savings; (iv) low cost device; (v) minimal energy input i.e. one small fan; (vi) can be retrofitted to existing buildings; (vii) its benefits were applicable at all of the (wide range of) locations tested.

Expediency of substitution of water heating with air heating involving use of heat pumps

2019 ◽  
Vol 12 (1) ◽  
pp. 45-49
Author(s):  
A. V. Martynov ◽  
N. E. Kutko
Keyword(s):  
Heat Pump ◽  
Ambient Air ◽  
Heat Pumps ◽  
Low Grade ◽  
Heating Season ◽  
Water Heating ◽  
Heating Systems ◽  
Air Heating ◽  
Transformation Ratio ◽  
Air Temperatures

Expediency is considered of substitution of water heating and transition to air heating that can be implemented with “air-air” type heat pumps (HP). The absence of water pipelines raises the reliability of heating systems. In addition to improved reliability, heat pumping systems ensure comfortable conditions for consumers at intervals between the heating seasons, when the central water heating is disabled.The “air-air” type HP use the ambient air as a low-grade heat source (LGHS). At low air temperatures, transformation ratio μ is about 2 and would rise to 3÷4 at higher air temperatures, which ensures high cost-efficiency of heating systems based on heat pumps. The heating season can generally be divided into two periods. One of the periods is characterized by the highest ambient air temperatures (–5÷8°С). This period is rather long and, in warmer winters, can last for about 4000 hours per heating season, or longer. This is the period, when the heat pump operates efficiently at a transformation ratio above 4.The other period, when the ambient temperature falls below –10÷ –20°С, generally lasts for a small number of hours, which makes about 15÷18% of the total duration of the heating season. At this period, the efficiency of the heat pump would decrease to μ =1.9÷2. Yet, even with such an efficiency, a heat pump delivers twice as much heat as the electric power it consumes.Therefore, in regions with a long period of temperatures within the range of –5÷8°С during a heating season, air heating based on HP can be advantageous compared to water heating.

A Model for a Geothermal Well in a Hydraulic Groundwater Flow for Ground Source Heat Pump Systems

2011 ◽  
Author(s):  
Kevin D. Woods ◽  
Alfonso Ortega
Keyword(s):  
Thermal Conductivity ◽  
Analytical Solution ◽  
Groundwater Flow ◽  
Heat Pump ◽  
Temperature Response ◽  
Ambient Air ◽  
Heat Pumps ◽  
Thermal Reservoir ◽  
Geothermal Well ◽  
Ground Source

Heat pumps are mechanical systems that provide heating to a space in the winter, and cooling in the summer. They are increasingly popular because the same system provides both cooling modes, depending on the direction of the cycle upon which they operate. For proper operation, the heat pump must be connected to a constant temperature thermal reservoir which in traditional systems is the ambient air. In ground source heat pumps however, subterranean ground water is used as the thermal reservoir. To access the subterranean groundwater, “geothermal” wells are drilled into the formation. Water from the building heating or cooling system is circulated through the wells thereby promoting heat exchange between the coolant water and the subterranean formation. The potential for higher efficiency heating and cooling has increased the utilization of ground source heating ventilating and air conditioning systems. In addition, their compatibility with a naturally occurring and stable thermal reservoir has increased their use in the design of sustainable or green buildings and man-made environments. Groundwater flow affects the temperature response of thermal wells due to advection of heat by physical movement of groundwater through the aquifer. Research on this subject is scarce in the geothermal literature. This paper presents the derivation of an analytical solution for thermal dispersion by conduction and advection from hydraulic groundwater flow for a “geothermal” well. This analytical solution is validated against asymptotic analytical solutions. The traditional constant linear heat source solution is dependent on the ground formation thermal properties; the most dominant of which is the thermal conductivity. The results show that as hydraulic groundwater flow increases, the influence of the ground formation thermal conductivity on the temperature response of the well diminishes. The diminishing influence is evident in the Peclet number parameter; a comparison of thermal advection from hydraulic groundwater flow to thermal conduction by molecular diffusion.

scholarly journals Heat pump systems: A mini review

2021 ◽  
Vol 4 (2) ◽  
pp. 73-81
Author(s):  
Mohammad Omar Temori ◽  
František Vranay
Keyword(s):  
Heat Pump ◽  
Electricity Consumption ◽  
Cost Savings ◽  
Electrical Energy ◽  
Primary Energy ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Heating And Cooling ◽  
Ground Source ◽  
Reduce Electricity Consumption

In this work, a mini review of heat pumps is presented. The work is intended to introduce a technology that can be used to income energy from the natural environment and thus reduce electricity consumption for heating and cooling. A heat pump is a mechanical device that transfers heat from one environmental compartment to another, typically against a temperature gradient (i.e. from cool to hot). In order to do this, an energy input is required: this may be mechanical, electrical or thermal energy. In most modern heat pumps, electrical energy powers a compressor, which drives a compression - expansion cycle of refrigerant fluid between two heat exchanges: a cold evaporator and a warm condenser. The efficiency or coefficient of performance (COP), of a heat pump is defined as the thermal output divided by the primary energy (electricity) input. The COP decreases as the temperature difference between the cool heat source and the warm heat sink increases. An efficient ground source heat pump (GSHP) may achieve a COP of around 4. Heat pumps are ideal for exploiting low-temperature environmental heat sources: the air, surface waters or the ground. They can deliver significant environmental (CO2) and cost savings.

Designing a novel solar-assisted heat pump system with modification of a thermal energy storage unit

2019 ◽  
Vol 233 (5) ◽  
pp. 588-603 ◽  
Author(s):  
Mustafa Aktaş ◽  
Meltem Koşan ◽  
Erhan Arslan ◽  
Azim Doğuş Tuncer
Keyword(s):  
Energy Storage ◽  
Solar Energy ◽  
Heat Pump ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Solar Collector ◽  
Working Fluid ◽  
Storage Unit ◽  
Heating Systems ◽  
Energy Storage Unit

The integrated usage of solar energy systems, heat pump applications, and thermal energy storage units is an effective way for heating systems due to their sustainability and stability in operations. In this study, a novel direct solar-assisted heat pump with thermal energy system has been designed which uses the solar collector as the evaporator of the heat pump. Besides, two-dimensional transient numeric analyses have been conducted for the thermal energy storage unit using the ANSYS Fluent 16.2 commercial software package. With this direct system, the heat required for heating systems is supplied from the condenser with the heat received from the solar collector of the working fluid. For an effective and high performance system, the solar collector is designed as a double-pass which provided superheating of the working fluid. It is aimed to store the surplus energy from the solar energy in the thermal energy storage unit and to operate the system continuously and efficiently in both sunny and overcast weather conditions. Furthermore, the system has been analyzed theoretically and the results show that coefficient of performance may improve. As a result, this newly designed system can be successfully applied for thermal applications.

Performance of Heat Pump Water Heater (HPWH) Systems and Their Impacts on Electric Utility Loads

2010 ◽  
Vol 2 (2) ◽  
Author(s):  
Yahya I. Sharaf-Eldeen
Keyword(s):  
Heat Pump ◽  
Energy Savings ◽  
Electric Energy ◽  
Cost Savings ◽  
Electric Heating ◽  
Electric Utility ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Water Heaters ◽  
Peak Loads

This work involves measurements, analyses, and evaluation of performance of air-source heat pump water heaters (HPWHs), and their impacts on electric utility loads. Two add-on, heat pumps (HPs) rated at 7000 BTU/h (2.051 kW) and 12,000 BTU/h (3.517 kW) were utilized. The HPs were retrofitted to two 50 gal (189.3 l) electric water heaters (EWHs) with their electric heating elements removed. A third standard EWH was used for comparison. The testing setups were fully instrumented for measurements of all pertinent parameters, including inlet and outlet water temperatures, inlet and outlet air temperatures of the HPs, temperature and humidity of the surrounding air, volume of water drawn out of the storage tanks, as well as the electric energy consumptions of the systems. Performance measures evaluated included the coefficient of performance, the energy factor (EF), and the first hour rating (FHR). The HPWH systems gave EFs ranging from 1.8 to 2.5 and corresponding energy savings (and reductions in utility peak loads) ranging from 49.0% to 63.0%, approximately. The values obtained in the summer months were, as expected, somewhat higher than those obtained in the winter ones. The average values of the EFs and energy savings (and reductions in utility peak loads) were about 2.1 and 56.0%, respectively. FHR results were much lower for the HPWHs compared with those for the standard EWH. These results show that HPWHs are much more efficient compared with standard EWHs. While the average value of the EF for the EWH was about 0.92, the HPWHs yielded EFs averaging more than 2.00, resulting in annual energy savings averaging more than 50%. The results also show that HPWHs are effective at reducing utility peak loads, in addition to providing substantial cost savings to consumers.

scholarly journals Optimization of emission reducing energy retrofits in Finnish apartment buildings

2019 ◽  
Vol 111 ◽  
pp. 03002 ◽  
Author(s):  
Janne Hirvonen ◽  
Juha Jokisalo ◽  
Juhani Heljo ◽  
Risto Kosonen
Keyword(s):  
Heat Pump ◽  
Life Cycle Cost ◽  
District Heating ◽  
Cost Savings ◽  
Cost Effective ◽  
Energy Performance ◽  
Heat Pumps ◽  
Apartment Buildings ◽  
Ground Source ◽  
Reduce Emissions

This study examined the cost-optimality of energy renovation on Finnish apartment buildings of different ages, built according to different energy performance requirements. Multi-objective optimization was utilized to minimize both CO2 emissions and life cycle cost (LCC). IDA-ICE simulations were performed to obtain the hourly heating demand of the buildings. Four building age classes and three heating systems (district heating, exhaust air heat pump and ground-source heat pump) were separately optimized. With district heating, it was possible to reduce emissions by 11%, while also reducing LCC. With heat pumps cost-savings could be achieved while reducing emissions by over 49%. With maximal (not cost-effective) investments, emissions could be reduced by more than 70% in all examined cases. In all cases, the cheapest solutions included solar electricity and sewage heat recovery. In old buildings, window upgrades and additional roof insulation were cost-effective. In new buildings, demand-based ventilation was included in all optimal solutions.

Using a Windbreak to Improve the Thermal Performance of a Flat Plate Solar Collector: A Feasibility Study

2011 ◽  
Author(s):  
Saeed Moaveni ◽  
Michael C. Watts
Keyword(s):  
Flat Plate ◽  
Heat Loss ◽  
Forced Convection ◽  
Thermal Performance ◽  
Solar Collector ◽  
Large Scale ◽  
Ambient Air ◽  
Absorber Plate ◽  
Wide Range ◽  
Flat Plate Solar Collector

During the past few decades, a wide range of studies have been performed to improve the performance of flat plate solar collectors by either reducing the heat loss from a collector or by increasing the amount of solar radiation absorbed by the absorber plate. Examples of these studies include adding transparent honeycomb to fill the air gap between the glazing and absorber plate to reduce convective heat loss, replacing the air in the gap by other gases such as Argon, Krypton, Xenon and Carbon Dioxide, or adding a chemical coating such as Copper Oxide to increase absorbtance and reduce the emittance of the absorber plate. While these methods improve the collector’s efficiency, they focus primarily on limiting the natural convection that occurs in the collector cavity, or on improving the optical properties of the absorber or glazing. None of these studies have addressed the problem of heat loss due to forced convection to the surrounding ambient air in any detail. Yet, research has shown that forced convection will contribute significantly to the heat loss from a collector. Windbreaks have traditionally been used to direct wind to protect farmland, and to direct wind drifts and sand dunes. Windbreaks also have been shown to provide protection for homes from winter winds which result in reduced heating costs for buildings. While windbreaks have been traditionally used for large scale applications, there is reason to believe that similar benefits can be expected for scaled down applications such as adding a windbreak along side of a flat-plate solar collector. In this paper, we examine the feasibility of using a windbreak to provide a flat plate solar collector protection from the wind in order to improve its performance. A series of experiments were performed wherein the thermal performance of two flat-plate collectors — one without a windbreaker and one with a windbreaker — were measured. The results of these experiments are reported in this paper and the need for further studies to explore different windbreak configurations is discussed.

scholarly journals A Low-Cost Wireless Temperature Sensor: Evaluation for Use in Environmental Monitoring Applications

2014 ◽  
Vol 31 (4) ◽  
pp. 938-944 ◽  
Author(s):  
Duick T. Young ◽  
Lee Chapman ◽  
Catherine L. Muller ◽  
Xiao-Ming Cai ◽  
C. S. B. Grimmond
Keyword(s):  
Environmental Monitoring ◽  
Air Temperature ◽  
Urban Areas ◽  
Low Cost ◽  
Ambient Air ◽  
Platinum Resistance ◽  
Dense Network ◽  
Radiation Shield ◽  
Wide Range ◽  
Monitoring Applications

Abstract A wide range of environmental applications would benefit from a dense network of air temperature observations. However, with limitations of costs, existing siting guidelines, and risk of damage, new methods are required to gain a high-resolution understanding of spatiotemporal patterns of temperature for agricultural and urban meteorological phenomena such as the urban heat island. With the launch of a new generation of low-cost sensors, it is possible to deploy a network to monitor air temperature at finer spatial resolutions. This study investigates the Aginova Sentinel Micro (ASM) sensor with a custom radiation shield (together less than USD$150) that can provide secure near-real-time air temperature data to a server utilizing existing (or user deployed) Wi-Fi networks. This makes it ideally suited for deployment where wireless communications readily exist, notably urban areas. Assessment of the performance of the ASM relative to traceable standards in a water bath and atmospheric chamber show it to have good measurement accuracy with mean errors <±0.22°C between −25° and 30°C, with a time constant in ambient air of 110 ±15 s. Subsequent field tests also showed the ASM (in the custom shield) had excellent performance (RMSE = 0.13°C) over a range of meteorological conditions relative to a traceable operational Met Office platinum resistance thermometer. These results indicate that the ASM and radiation shield are more than fit for purpose for dense network deployment in environmental monitoring applications at relatively low cost compared to existing observation techniques.

Low-Cost Adhesives for Temporary Substrate Support

2012 ◽  
Vol 2012 (DPC) ◽  
pp. 1-60
Author(s):  
John Moore ◽  
Jared Pettit
Keyword(s):  
Current Practice ◽  
Low Cost ◽  
Cost Savings ◽  
Specific Design ◽  
Substrate Support ◽  
Wide Range ◽  
Rapid Removal ◽  
Green Factory ◽  
The Right ◽  
Simple Materials

Temporary adhesives are a key part to 3DIC integration. Choosing the right adhesive is critical as it defines your process, tooling needs, and by virtue of its chemistry, will control throughput and yield. Although several products and tooling exist in the market, few offer a clear path to achieve HVM at an affordable cost. [1] A wide range in materials and processes are available, most which can be tailored to a specific design or tooling objective. Multiple options in adhesives allow grinding and polishing to <20um, protection during backside processing (e.g. TSVs), thermal resistance to >400C, [2] CVD acceptance (Fig. 1), and rapid removal with cleans on a film frame (Fig. 2). Using batch processing, throughput is increased by a factor of 5 while cost is reduced by 50%, suggesting a COO that is 10% relative to current practice. Instituting simple materials and processes matched to a customer's design will provide benefits beyond cost savings, including “green factory” certification. This presentation reviews several current practices in the market and contrasts these options with alternative low-cost adhesives and processes that are tuned to a customer's product design and tooling. Examples include excerpts from handling thin substrates in semiconductor, solar, and TFT/LCD fabrication lines.

Sign in / Sign up

Export Citation Format

Share Document