scholarly journals An approach for determining the water injection pressure of low-permeability reservoirs

2018 ◽  
Vol 36 (5) ◽  
pp. 1210-1228 ◽  
Author(s):  
Wenya Lyu ◽  
Lianbo Zeng ◽  
Minzheng Chen ◽  
Dongsheng Qiao ◽  
Jianming Fan ◽  
...  
Keyword(s):  
Ordos Basin ◽  
Water Injection ◽  
Injection Pressure ◽  
Production Performance ◽  
Low Permeability ◽  
Bohai Bay ◽  
Natural Fractures ◽  
Effective Measure ◽  
Water Breakthrough ◽  
Low Permeability Reservoirs

Waterflooding is an important functional process for low-permeability reservoir development. However, production practice shows that water breakthrough and floods along natural fractures are ubiquitous in low-permeability reservoirs. Therefore, controlling the water injection pressure to prevent water breakthrough and floods along natural fractures is an effective measure for improving the waterflooding development effect. In this paper, an approach is proposed for determining the water injection pressure based on the opening pressure of natural fractures in fractured low-permeability reservoirs. The opening pressures of natural fractures calculated by the analytical method in the paper and the formation-parting pressures are compared based on the production performance in two different fault blocks F16 and Z3 of the Zhouqingzhuang Oilfield in the Bohai Bay Basin, China. The results show that the calculated opening pressures of the natural fractures in fault blocks F16 and Z3 are 31.4 and 42.9 MPa, respectively, and they are close to the opening pressures of natural fractures obtained from the step-rate tests in injection wells (28.6 and 41.1 MPa); whereas, the formation-parting pressures (44.5 and 47.6 MPa) are greater than the opening pressures of natural fractures. This suggests that the opening pressures of natural fractures can be used, instead of the formation-parting pressure, for the maximum threshold of the water injection pressure. Its effectiveness has been confirmed via comparison to the production performances of the other two wells in the Zhouqingzhuang Oilfield and several fractured low-permeability reservoirs in the Ordos Basin, China. This study will have beneficial applications in the design of waterflooding development in low-permeability reservoirs characterized by the presence of natural fractures.

The Research and Evaluation of Finely Layered Water Injection Standard in Low-Permeability Reservoirs - A Case from Block A in one Low-Permeability Reservoir

2014 ◽  
Vol 1073-1076 ◽  
pp. 2310-2315 ◽  
Author(s):  
Ming Xian Wang ◽  
Wan Jing Luo ◽  
Jie Ding
Keyword(s):  
Oil Recovery ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection Rate ◽  
Low Permeability ◽  
Reservoir Permeability ◽  
Engineering Parameters ◽  
The Common ◽  
Common Problems ◽  
Low Permeability Reservoirs

Due to the common problems of waterflood in low-permeability reservoirs, the reasearch of finely layered water injection is carried out. This paper established the finely layered water injection standard in low-permeability reservoirs and analysed the sensitivity of engineering parameters as well as evaluated the effect of the finely layered water injection standard in Block A with the semi-quantitative to quantitative method. The results show that: according to the finely layered water injection standard, it can be divided into three types: layered water injection between the layers, layered water injection in inner layer, layered water injection between fracture segment and no-fracture segment. Under the guidance of the standard, it sloved the problem of uneven absorption profile in Block A in some degree and could improve the oil recovery by 3.5%. The sensitivity analysis shows that good performance of finely layered water injection in Block A requires the reservoir permeability ratio should be less than 10, the perforation thickness should not exceed 10 m, the amount of layered injection layers should be less than 3, the surface injection pressure should be below 14 MPa and the injection rate shuold be controlled at about 35 m3/d.

Nanotechnology Helps Decrease Pressure, Increase Injection in Offshore China Oil Field

2021 ◽  
Vol 73 (09) ◽  
pp. 58-59
Author(s):  
Chris Carpenter
Keyword(s):  
Water Injection ◽  
Injection Pressure ◽  
Gas Production ◽  
Oil Field ◽  
Water Flooding ◽  
Injection System ◽  
Bohai Bay ◽  
Reservoir Properties ◽  
Positive Effects ◽  
Offshore Technology

This article, written by JPT Technology Editor Chris Carpenter, contains highlights of paper OTC 30407, “Case Study of Nanopolysilicon Materials’ Depressurization and Injection-Increasing Technology in Offshore Bohai Bay Oil Field KL21-1,” by Qing Feng, Nan Xiao Li, and Jun Zi Huang, China Oilfield Services, et al., prepared for the 2020 Offshore Technology Conference Asia, originally scheduled to be held in Kuala Lumpur, 2–6 November. The paper has not been peer reviewed. Copyright 2020 Offshore Technology Conference. Reproduced by permission. Nanotechnology offers creative approaches to solve problems of oil and gas production that also provide potential for pressure-decreasing application in oil fields. However, at the time of writing, successful pressure-decreasing nanotechnology has rarely been reported. The complete paper reports nanopolysilicon as a new depressurization and injection-increasing agent. The stability of nanopolysilicon was studied in the presence of various ions, including sodium (Na+), calcium (Ca2+), and magnesium (Mg2+). The study found that the addition of nanomaterials can improve porosity and permeability of porous media. Introduction More than 600 water-injection wells exist in Bohai Bay, China. Offshore Field KL21-1, developed by water-flooding, is confronted with the following challenges: - Rapid increase and reduction of water-injection pressure - Weak water-injection capacity of reservoir - Decline of oil production - Poor reservoir properties - Serious hydration and expansion effects of clay minerals To overcome injection difficulties in offshore fields, conventional acidizing measures usually are taken. But, after multiple cycles of acidification, the amount of soluble substances in the rock gradually decreases and injection performance is shortened. Through injection-performance experiments, it can be determined that the biological nanopolysilicon colloid has positive effects on pressure reduction and injection increase. Fluid-seepage-resistance decreases, the injection rate increases by 40%, and injection pressure decreases by 10%. Features of Biological Nanopolysilicon Systems The biological nanopolysilicon-injection system was composed of a bioemulsifier (CDL32), a biological dispersant (DS2), and a nanopolysilicon hydrophobic system (NP12). The bacterial strain of CDL32 was used to obtain the culture colloid of biological emulsifier at 37°C for 5 days. DS2 was made from biological emulsifier CDL32 and some industrial raw materials described in Table 1 of the complete paper. Nanopolysilicon hydrophobic system NP12 was composed of silicon dioxide particles. The hydrophobic nanopolysilicons selected in this project featured particle sizes of less than 100 nm. In the original samples, a floc of nanopolysilicon was fluffy and uniform. But, when wet, nanopolysilicon will self-aggregate and its particle size increases greatly. At the same time, nanopolysilicon features significant agglomeration in water. Because of its high interface energy, nanopolysilicon is easily agglomerated, as shown in Fig. 1.

Research on Flow Units of Extra-Low Permeability Reservoirs in Fault Block Sheng554 of Shengping Oilfield

2013 ◽  
Vol 295-298 ◽  
pp. 3162-3165
Author(s):  
Lu Lu Zhou ◽  
Zi Nan Li ◽  
Jun Gang Liu ◽  
Yan Yun Zhang ◽  
Guang Qiang Shu
Keyword(s):  
Fluid Flow ◽  
Water Injection ◽  
Type A ◽  
Low Permeability ◽  
Type B ◽  
Flow Units ◽  
Fault Block ◽  
Remaining Oil ◽  
Type C ◽  
Low Permeability Reservoirs

Taking the example of the fourth member of the Lower Cretaceous Quantou formation reservoirs in fault block Sheng554 of Sanzhao sag, this article discusses the methodology of flow units in extra-low permeability reservoirs. The research on flow units in such reservoirs can be divided into two ranks, one is to determine the distribution of seepage barriers and inner connected sands， the other is to analyze the differentia of fluid flow in the inner connected sands so as to subdivide the flow units. The result shows that the pelitic barriers are rather developed in fault block Sheng554. Through the analysis of differentia of fluid flow, according to the value of flow zone index (FZI), the inner connected sands can be classified into three types of flow units, among which type A with FZI value greater than 1.0 has better permeable property and higher intensity of water injection, and the ability of permeability and water injection of type B with FZI value between 0.5 and 1.0 takes the second place, and type C is the worst flow unit with the worst permeable property and intensity of water injection with FZI value less than 0.5. Among the three types of flow units, type A poorly develops, while type B and type C develops well. The research on flow units can provide reliable geologic bases for forecasting the distribution of remaining oil in extra-low permeability reservoirs and for developing remaining oil in the study area.

scholarly journals Semi-analytical modeling of advanced water injection in low permeability reservoirs under non-Darcy-flow condition

2019 ◽  
Vol 11 (5) ◽  
pp. 168781401984676 ◽  
Author(s):  
Chengyong Li ◽  
Jing Yang ◽  
Jianwen Ye ◽  
Jun Zhou ◽  
Ran Zhang ◽  
...  
Keyword(s):  
Flow Condition ◽  
Analytical Modeling ◽  
Water Injection ◽  
Darcy Flow ◽  
Low Permeability ◽  
Low Permeability Reservoirs

Parametric Study of Channeling Flow in Low Permeability Reservoir with Mudstone Interlayer

2012 ◽  
Vol 524-527 ◽  
pp. 1190-1195
Author(s):  
Jian Jun Liu ◽  
Quan Shu Li ◽  
Gui Hong Pei
Keyword(s):  
High Pressure ◽  
Water Injection ◽  
Injection Pressure ◽  
Element Model ◽  
Low Permeability ◽  
Low Permeability Reservoir ◽  
Injection Process ◽  
Well Spacing ◽  
Pressure Water ◽  
Channeling Flow

Channeling flow frequently occurs during the high pressure water injection of low permeability reservoir. The injection process is complex and covers so many parameters of which the contribution to channeling flow is necessarily to be studied. In this paper, numerical simulation is combined with sensitivity analysis method to calculate the significance of the weight of parameters to the channeling flow. First the values of different parameters are produced by using Latin hypercube method; second, by using these parameters, finite element model have been established and simulated, and the quantity of channeling flow has been calculated; then Spearman rank relation is applied to measure the relation of parameters and channeling flow. The results states that, in 10 years continuous injection, the well spacing and injection pressure have significant impact on the channeling flow. This states that during the application of high pressure water injection, the pressure and well spacing should be controlled especially.

Research of Improving Water Injection Effect by Using Active SiO2 Nano-Powder in the Low-Permeability Oilfield

2010 ◽  
Vol 92 ◽  
pp. 207-212 ◽  
Author(s):  
Ke Liang Wang ◽  
Shou Cheng Liang ◽  
Cui Cui Wang
Keyword(s):  
Oil Recovery ◽  
Pore Volume ◽  
Water Injection ◽  
Field Tests ◽  
Injection Pressure ◽  
Rock Surface ◽  
Low Permeability ◽  
Injection Wells ◽  
Decompression Rate ◽  
Nano Powder

SiO2 nano-powder is a new type of augmented injection agent, has the ability of stronger hydrophobicity and lipophilicity, and can be adsorbed on the rock surface so that it changes the rock wettability. It can expand the pore radius effectively, reduce the flow resistance of injected water in the pores, enhance water permeability, reduce injection pressure and augment injection rate. Using artificial cores which simulated geologic conditions of a certain factory of Daqing oilfield, decompression and augmented injection experiments of SiO2 nano-powder were performed after waterflooding, best injection volume of SiO2 nano-powder under the low-permeability condition was selected. It has shown that SiO2 nano-powder inverted the rock wettability from hydrophilicity to hydrophobicity. Oil recovery was further enhanced after waterflooding. With the injection pore volume increasing, the recovery and decompression rate of SiO2 nano-powder displacement increased gradually. The best injected pore volume and injection concentration is respectively 0.6PV and 0.5%, the corresponding value of EOR is 6.84% and decompression rate is 52.78%. According to the field tests, it is shown that, in the low-permeability oilfield, the augmented injection technology of SiO2 nano-powder could enhance water injectivity of injection wells and reduce injection pressure. Consequently, it is an effective method to resolve injection problems for the low-permeability oilfield.

Main Controlled Elements for Accumulation of Ultro-Low Permeability Sandstone Oil Reservoir, Zhenjing Oilfield, Ordas Basin

2013 ◽  
Vol 868 ◽  
pp. 70-73
Author(s):  
Yi Wei Hao ◽  
Hai Yan Hu
Keyword(s):  
Oil And Gas ◽  
Sedimentary Basin ◽  
Ordos Basin ◽  
Low Permeability ◽  
Oil Reservoir ◽  
Tight Sandstone ◽  
Buoyant Force ◽  
Accumulation Mechanism ◽  
Oil And Gas Resources ◽  
Low Permeability Reservoirs

Ordos Basin is the second largest sedimentary basin in China with very rich oil and gas resources. The exploration targets are typical reservoirs of low permeability. To determine the accumulation mechanism of tight sandstone reservoir, thin section, SEM, numerical calculation were used. The result showed that sandstone should be ultro-low permeability reservoirs with the high content feldspar and lithic arkose or feldspathic litharenite. The reservoir became tight while oil filling, buoyant force is too small to overcome the resistance of capillary force. Therefore, overpressure induced by source rock generation is the accumulation drive force.

Adaptability Evaluation of Conformance Control Agents in Low Permeability Reservoirs with Fractures

2014 ◽  
Vol 960-961 ◽  
pp. 170-175
Author(s):  
Feng Lan Zhao ◽  
Shu Jun Cao ◽  
Ji Rui Hou
Keyword(s):  
Graft Copolymer ◽  
Polymer Concentration ◽  
Gelation Time ◽  
Injection Pressure ◽  
Low Permeability ◽  
Particle Type ◽  
Conformance Control ◽  
Fracture Width ◽  
Preformed Particle Gel ◽  
Low Permeability Reservoirs

Several conformance control agents, including preformed particle gel, emulsion microspheres, continuous chromium gel and underground starch graft copolymer gel were evaluated. The properties such as gelation time and gel strength of gel, and expansion of particles and microspheres were tested at high temperature. Also, the injection pressure, plugging strength and resistance factor were measured using the artificial low permeability cores with fractures. It was shown that, for particle type conformance control agents, the particle size should be adaptable with the fracture width. Also, for continuous chromium gel, the added polymer concentration higher, the viscosity is higher, with higher plugging strength. The plugging and strength should be coordinated. The starch graft copolymer gel is easy to be injected into formation and has good plugging property. The results show that underground starch graft gel is more suitable for conformance control in low permeability formation with fractures.

Sign in / Sign up

Export Citation Format

Share Document