The Research and Evaluation of Finely Layered Water Injection Standard in Low-Permeability Reservoirs - A Case from Block A in one Low-Permeability Reservoir

2014 ◽  
Vol 1073-1076 ◽  
pp. 2310-2315 ◽  
Author(s):  
Ming Xian Wang ◽  
Wan Jing Luo ◽  
Jie Ding
Keyword(s):  
Oil Recovery ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection Rate ◽  
Low Permeability ◽  
Reservoir Permeability ◽  
Engineering Parameters ◽  
The Common ◽  
Common Problems ◽  
Low Permeability Reservoirs

Due to the common problems of waterflood in low-permeability reservoirs, the reasearch of finely layered water injection is carried out. This paper established the finely layered water injection standard in low-permeability reservoirs and analysed the sensitivity of engineering parameters as well as evaluated the effect of the finely layered water injection standard in Block A with the semi-quantitative to quantitative method. The results show that: according to the finely layered water injection standard, it can be divided into three types: layered water injection between the layers, layered water injection in inner layer, layered water injection between fracture segment and no-fracture segment. Under the guidance of the standard, it sloved the problem of uneven absorption profile in Block A in some degree and could improve the oil recovery by 3.5%. The sensitivity analysis shows that good performance of finely layered water injection in Block A requires the reservoir permeability ratio should be less than 10, the perforation thickness should not exceed 10 m, the amount of layered injection layers should be less than 3, the surface injection pressure should be below 14 MPa and the injection rate shuold be controlled at about 35 m3/d.

The Porous Medium of Ultra-Low Permeability Reservoir has an Effect on Oil Recovery

2013 ◽  
Vol 779-780 ◽  
pp. 1457-1461
Author(s):  
Xian Wen Li ◽  
Chun Mei Xu ◽  
Fang Yuan Guo ◽  
Xing Hong Wang
Keyword(s):  
Porous Medium ◽  
Oil Recovery ◽  
Research Result ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection Rate ◽  
Particle Migration ◽  
Low Permeability ◽  
Reservoir Water ◽  
Low Permeability Reservoir

This paper from the research of the porous medium pore structure characteristics of ultra-low permeability reservoir, combined the core flow test with reservoir characteristics analysis and fluid properties analysis studying the reservoir water injection development effect. The research results show that: the microscopic heterogeneity of ultra-low permeability reservoir is strong, pore connectivity of porous medium is poor, seepage throat is very fine and microcrack is growth. During the process of water injection development there exist particle migration phenomenon, could easily cause pore throat blockage, and lead to water injection pressure rebound. According to the research result targeted on the organic mud acid deep broken down experiment, the result shows that it can achieve the purpose of depressure and increasing injection rate.

Research of Improving Water Injection Effect by Using Active SiO2 Nano-Powder in the Low-Permeability Oilfield

2010 ◽  
Vol 92 ◽  
pp. 207-212 ◽  
Author(s):  
Ke Liang Wang ◽  
Shou Cheng Liang ◽  
Cui Cui Wang
Keyword(s):  
Oil Recovery ◽  
Pore Volume ◽  
Water Injection ◽  
Field Tests ◽  
Injection Pressure ◽  
Rock Surface ◽  
Low Permeability ◽  
Injection Wells ◽  
Decompression Rate ◽  
Nano Powder

SiO2 nano-powder is a new type of augmented injection agent, has the ability of stronger hydrophobicity and lipophilicity, and can be adsorbed on the rock surface so that it changes the rock wettability. It can expand the pore radius effectively, reduce the flow resistance of injected water in the pores, enhance water permeability, reduce injection pressure and augment injection rate. Using artificial cores which simulated geologic conditions of a certain factory of Daqing oilfield, decompression and augmented injection experiments of SiO2 nano-powder were performed after waterflooding, best injection volume of SiO2 nano-powder under the low-permeability condition was selected. It has shown that SiO2 nano-powder inverted the rock wettability from hydrophilicity to hydrophobicity. Oil recovery was further enhanced after waterflooding. With the injection pore volume increasing, the recovery and decompression rate of SiO2 nano-powder displacement increased gradually. The best injected pore volume and injection concentration is respectively 0.6PV and 0.5%, the corresponding value of EOR is 6.84% and decompression rate is 52.78%. According to the field tests, it is shown that, in the low-permeability oilfield, the augmented injection technology of SiO2 nano-powder could enhance water injectivity of injection wells and reduce injection pressure. Consequently, it is an effective method to resolve injection problems for the low-permeability oilfield.

Optimizing Recovery for Waterflooding Under Dynamic Induced Fracturing Conditions

2009 ◽  
Vol 12 (05) ◽  
pp. 671-682 ◽  
Author(s):  
Paul J. van den Hoek ◽  
Rashid A. Al-Masfry ◽  
Dirk Zwarts ◽  
Jan-Dirk Jansen ◽  
Bernhard Hustedt ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Water Injection ◽  
Injection Rate ◽  
Reservoir Engineering ◽  
Spot Pattern ◽  
Engineering Parameters ◽  
Induced Fractures ◽  
Modeling Strategy ◽  
Reservoir Simulator ◽  
Fully Coupled

Summary It is well established within the industry that water injection mostly takes place under induced fracturing conditions. Particularly in low-mobility reservoirs, large fractures may be induced during the field life. This paper presents a new modeling strategy that combines fluid flow and fracture growth (fully coupled) within the framework of an existing "standard" reservoir simulator. We demonstrate the coupled simulator by applications to repeated five-spot pattern flood models, addressing various aspects that often play an important role in waterfloods: shortcut of injector and producer, fracture containment to the reservoir layer, and areal and vertical reservoir sweep. We also demonstrate how induced fracture dimensions (length, height) can be very sensitive to typical reservoir engineering parameters, such as fluid mobility, mobility ratio, 3D saturation distribution (in particular, shockfront position), 3D temperature distribution, positions of wells (producers, injectors), and geological details (e.g., layering and faulting). In particular, it is shown that lower overall (time-dependent) reservoir transmissibility will result in larger induced fractures. Finally, it is demonstrated how induced fractures can be taken into account to determine an optimum life-cycle injection rate strategy. The results presented in this paper are expected to also apply to (part of) enhanced-oil-recovery operations (e.g., polymer flooding).

scholarly journals Experimental Study on Enhanced Oil Recovery by Nitrogen-Water Alternative Injection in Reservoir with Natural Fractures

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiang Li ◽  
Yuan Cheng ◽  
Wulong Tao ◽  
Shalake Sarulicaoketi ◽  
Xuhui Ji ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Gas Injection ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection Rate ◽  
Water Flooding ◽  
Orthogonal Experimental Design ◽  
Fractured Reservoir ◽  
Natural Fractures ◽  
Nitrogen Injection

The production of a low permeability reservoir decreases rapidly by depletion development, and it needs to supplement formation energy to obtain stable production. Common energy supplement methods include water injection and gas injection. Nitrogen injection is an economic and effective development method for specific reservoir types. In order to study the feasibility and reasonable injection parameters of nitrogen injection development of fractured reservoir, this paper uses long cores to carry out displacement experiment. Firstly, the effects of water injection and nitrogen injection development of a fractured reservoir are compared through experiments to demonstrate the feasibility of nitrogen injection development of the fractured reservoir. Secondly, the effects of gas-water alternate displacement after water drive and gas-water alternate displacement after gas drive are compared through experiments to study the situation of water injection or gas injection development. Finally, the reasonable parameters of nitrogen gas-water alternate injection are optimized by orthogonal experimental design. Results show that nitrogen injection can effectively enhance oil production of the reservoir with natural fractures in early periods, but gas channeling easily occurs in continuous nitrogen flooding. After water flooding, gas-water alternate flooding can effectively reduce the injection pressure and improve the reservoir recovery, but the time of gas-water alternate injection cannot be too late. It is revealed that the factors influencing the nitrogen-water alternative effect are sorted from large to small as follows: cycle injected volume, nitrogen and water slug ratio, and injection rate. The optimal cycle injected volume is around 1 PV, the nitrogen and water slug ratio is between 1 and 2, and the injection rate is between 0.1 and 0.2 mL/min.

Optimized Cyclic Water Injection Strategy for Oil Recovery in Low-Permeability Reservoirs

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Xiaofei Sun* ◽  
Yanyu Zhang ◽  
Jie Wu ◽  
Mengke Xie ◽  
Hang Hu
Keyword(s):  
Oil Recovery ◽  
Water Injection ◽  
Tracer Tests ◽  
Oil Prices ◽  
Fuzzy Comprehensive Evaluation ◽  
Low Permeability ◽  
Operational Parameters ◽  
Recovery Method ◽  
Low Permeability Reservoir ◽  
Low Permeability Reservoirs

With the worldwide decline in conventional oil production, tremendous unconventional resources, such as low-permeability reservoirs, are becoming increasingly important. Cyclic water injection (CWI) as an oil recovery method has attracted increasing attention in the present environment of low oil prices. However, the optimal CWI strategy is difficult to determine for a mature oilfield due to the involvement of multiple wells with multiple operational parameters. Thus, our main focus in this paper is to present a novel and systematic approach to optimize CWI strategies by studying a typical low-permeability, namely, reservoir G21. To this end, a comprehensive method that combines the advantages of streamline simulation and fuzzy comprehensive evaluation (FCE) was proposed to identify water channeling in the reservoir. Second, the reliability of the method was verified using tracer tests. Finally, a new hybrid optimization algorithm, the simulated annealing-genetic algorithm (SAGA), coupled with a reservoir simulator was developed to determine an optimal CWI strategy for the low-permeability reservoir. The results show that the CWI technique is viable as a primary means in the present environment of low oil prices to improve the waterflood performance in low-permeability reservoirs. The oil recovery of the most efficient strategy increases by 6.8% compared to conventional waterflooding. The asymmetric CWI scheme is more efficient than the symmetric CWI scheme for the low-permeability reservoir.

A Study of Seepage Characteristics of Unsteady Waterflooding Development for Fractured Ultra-Low-Permeability Reservoir

2021 ◽  
Author(s):  
Qing Liu ◽  
Xiangfang Li ◽  
Jian Yang ◽  
Sen Feng ◽  
Minxia He ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Simulation Model ◽  
Water Injection ◽  
Injection Rate ◽  
Low Permeability ◽  
Tensor Model ◽  
Capillary Imbibition ◽  
Low Permeability Reservoir ◽  
Water Cut ◽  
Low Permeability Reservoirs

Abstract Unconventional fractured ultra-low-permeability reservoirs play an important role in continental sedimentary basins in China, and their formation characteristics and seepage laws are greatly different from that of traditional reservoirs. In this paper, the influence of microfractures and unsteady waterflooding on the productivity of fractured ultra-low permeability reservoirs are studied deeply. The reservoir parameters used in the study are from an actual fractured ultra-low-permeability reservoir in Ordos Basin, where microfractures are developed but macroscopic fractures are not. The microfractures have a small opening and are widely distributed in the reservoir, so the reservoir numerical simulation model adopts the equivalent continuous matrix model to simulate waterflooding. On one hand, the physical model of micro-fractured reservoir and the permeability tensor model of the equivalent continuous matrix are established. The results show that the existence of microfractures can increase the permeability of matrix by 1.4 times. On the other hand, an ideal heterogeneous numerical simulation model composed of pure matrix and equivalent continuous matrix considering microfracture is established according to actual geological parameters of the fractured ultra-low-permeability reservoir. To simulate and compare the unsteady waterflooding and continuous waterflooding development in 10-year development under the condition of constant annual injection rate, the results indicate that unsteady waterflooding development make higher productivity and lower water cut and lower formation water saturation than that of continuous waterflooding. By conducting unsteady waterflooding development simulation for sensitivity analysis, the results demonstrate that the greater the capillary force, the better the role of capillary imbibition in a certain range, meanwhile, the unsteady waterflooding has the best exploitation effect when the value of water injection cycle time is 100 days and the fluctuation amplitude of water injection rate is 1. At the above situation, the displacement and capillary imbibition and pressure disturbance achieve the desired effect of reducing water cut and increasing oil production.

Injection Strategies To Overcome Gravity Segregation in Simultaneous Gas and Water Injection Into Homogeneous Reservoirs

SPE Journal ◽  
2009 ◽  
Vol 15 (01) ◽  
pp. 76-90 ◽  
Author(s):  
W.R.. R. Rossen ◽  
C.J.. J. van Duijn ◽  
Q.P.. P. Nguyen ◽  
C.. Shen ◽  
A.K.. K. Vikingstad
Keyword(s):  
Water Flow ◽  
Oil Recovery ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection Rate ◽  
Numerical Dispersion ◽  
Horizontal Distance ◽  
Mixed Gas ◽  
Gravity Segregation ◽  
Vertical Well

Summary We extend a model for gravity segregation in steady-state gas/water injection into homogeneous reservoirs for enhanced oil recovery (EOR). A new equation relates the distance gas and water flow together directly to injection pressure, independent of fluid mobilities or injection rate. We consider three additional cases: coinjection of gas and water over only a portion of the formation interval, injection of water above gas over the entire formation interval, and injection of water and gas in separate zones well separated from each other. If gas and water are injected at fixed total volumetric rates, the horizontal distance to the point of complete segregation is the same, whether gas and water are coinjected over all or any portion of the formation interval. At fixed injection pressure, the deepest penetration of mixed gas and water flow is expected when fluids are injected along the entire formation interval. At fixed total injection rate, injection of water above gas gives deeper penetration before complete segregation than does coinjection, but again exactly where the two fluids are injected does not affect the distance to the point of segregation. At fixed injection pressure, injection of water above gas is predicted to give deeper penetration before complete segregation. When injection pressure is limited, the best strategy for simultaneous injection of both phases from a vertical well would be to inject gas at the bottom of the reservoir and water over the rest of the reservoir height, with the ratio of the injection intervals adjusted to maximize overall injectivity. The 2D model applies equally to gas/water flow and to foam, and to injection of water above gas from separate intervals of a vertical well or from two parallel horizontal wells, as long as injection is uniform along each horizontal well. Sample computer simulations for foam injection agree well with the model predictions if numerical dispersion is controlled.

scholarly journals Mechanism of Enhanced Oil Recovery for In-Depth Profile Control and Cyclic Waterflooding in Fractured Low-Permeability Reservoirs

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Daiyin Yin ◽  
Wei Zhou
Keyword(s):  
Enhanced Oil Recovery ◽  
Depth Profile ◽  
Oil Recovery ◽  
Water Injection ◽  
High Water ◽  
Low Permeability ◽  
Profile Control ◽  
High Water Cut ◽  
Water Cut ◽  
Low Permeability Reservoirs

When fractured low-permeability reservoirs enter a high water cut period, injected water always flows along fractures, water cut speeds increase rapidly, and oil production decreases quickly in oil wells. It is difficult to further improve the oil recovery of such fractured low-permeability reservoirs. In this paper, based on the advantages of in-depth profile control and cyclic water injection, the feasibility of combining deep profile control with cyclic water injection to improve oil recovery in fractured low-permeability reservoirs during the high water cut stage was studied, and the mechanisms of in-depth profile control and cyclic waterflooding were investigated. According to the characteristics of reservoirs in Zone X, as well as the fracture features and evolution mechanisms of the well network, an outcrop plate fractured core model that considers fracture direction was developed, and core displacement experiments were carried out by using the HPAM/Cr3+ gel in-depth profile control system. The enhanced oil recovery of waterflooding, cyclic water injection, and in-depth profile control, as well as a combination of in-depth profile control and cyclic water injection, was investigated. Moreover, variations in the water cut degree, reserve recovery percentage, injection pressure, fracture and matrix pressure, and water saturation were monitored. On this basis, the mechanism of enhanced oil recovery based on the combined utilization of in-depth profile control and cyclic waterflooding methods was analyzed. The results show that in-depth profile control and cyclic water injection can be synchronized to further increase oil recovery. The recovery ratio under the combination of in-depth profile control and cyclic water injection was 1.9% higher than that under the in-depth profile control and 5.6% higher than that under cyclic water injection. The combination of in-depth profile control and cyclic water injection can increase the reservoir pressure; therefore, the fluctuation of pressure between the matrix and its fractures increases, more crude oil flows into the fracture, and the oil production increases.

Analysis of the channeling of water injection in low permeability reservoirs with interlayer considering the seepage–stress coupling

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ji Youjun ◽  
K. Vafai ◽  
Huijin Xu ◽  
Liu Jianjun
Keyword(s):  
Water Injection ◽  
Simulation Method ◽  
Stress Sensitivity ◽  
Injection Rate ◽  
Water Flooding ◽  
Low Permeability ◽  
Content Type ◽  
Main Injection ◽  
Low Permeability Reservoirs ◽  
The Impact

Purpose This paper aims to establish a mathematical model for water-flooding considering the impact of fluid–solid coupling to describe the process of development for a low-permeability reservoir. The numerical simulation method was used to analyze the process of injected water channeling into the interlayer. Design/methodology/approach Some typical cores including the sandstone and the mudstone were selected to test the permeability and the stress sensitivity, and some curves of the permeability varying with the stress for the cores were obtained to demonstrate the sensitivity of the formation. Based on the experimental results and the software Eclipse and Abaqus, the main injection parameters to reduce the amount of the injected water in flowing into the interlayer were simulated. Findings The results indicate that the permeability of the mudstone is more sensitive to the stress than sandstone. The injection rate can be as high as possible on the condition that no crack is activated or a new fracture is created in the development. For the B82 block of Daqing oilfield, the suggested pressure of the production pressure should be around 1–3MPa, this pressure must be gradually reached to get a higher efficiency of water injection and avoid damaging the casing. Originality/value This work is beneficial to ensure stable production and provide technical support to the production of low permeability reservoirs containing an interlayer.

scholarly journals Experimental Study on the Effect of ASP Flooding on Improving Oil Recovery in Low Permeability Reservoirs Based on a Partial Quality Tool

Processes ◽  
2020 ◽  
Vol 8 (3) ◽  
pp. 296 ◽  
Author(s):  
Bin Huang ◽  
Xinyu Hu ◽  
Cheng Fu ◽  
Quan Zhou
Keyword(s):  
Molecular Weight ◽  
High Molecular Weight ◽  
Oil Recovery ◽  
Injection Pressure ◽  
Low Permeability ◽  
Displacement Effect ◽  
Oil Displacement ◽  
Matching Degree ◽  
Low Permeability Reservoirs ◽  
Quality Tool

In order to solve the problem of the poor oil displacement effect of high molecular weight alkali/surfactant/polymer (ASP) solution in low permeability reservoirs, Daqing Oilfield uses a partial quality tool to improve the oil displacement effect in low permeability reservoirs. In the formation, the partial quality tool degrades the polymer through active shearing action, reducing the molecular weight of the polymer, to improve the matching degree to the low permeability oil layer and the oil recovery. In order to study the ability of the partial quality tool to improve the oil displacement effect, the matching degree of high molecular weight ASP solution to low permeability cores is studied, and the ability of quality control tools to change the molecular weight is studied. Then, experimental research on the pressure and oil displacement effect of high molecular weight ASP solution before and after the actions of the partial quality tool is carried out. The results show that ASP solutions with molecular weights of 1900 × 104 and 2500 × 104 have a poor oil displacement effect in low permeability reservoirs. After the action of the partial quality tool, the injection pressure is reduced by 5.22 MPa, and the oil recovery is increased by 7.79%. The injection pressure of the ASP solution after shearing by the partial quality tool is lower than that of the ASP solution with the same molecular weight and concentration without shearing, but the oil recovery is lower. On the whole, the use of the partial quality tool can obviously improve the oil displacement effect in low permeability reservoirs.

Sign in / Sign up

Export Citation Format

Share Document