Low-cost biodiesel production using waste oil and catalyst

2020 ◽  
pp. 0734242X2093517
Author(s):  
Raheleh Talavari ◽  
Shokoufe Hosseini ◽  
GR Moradi
Keyword(s):  
Electron Microscopy ◽  
Fossil Fuels ◽  
Building Materials ◽  
Raw Materials ◽  
Low Cost ◽  
High Strength ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Waste Frying Oil ◽  
X Ray

With the production of renewable biofuels, concerns about the end of fossil fuels have been partially eliminated. On the other hand, the utilization of low-cost and waste materials to provide the raw essential substances to manufacture these fuels is of paramount importance. Biodiesel is one of these fuels and the required raw materials for the reaction are oil (triglycerides), alcohol and catalyst. In this work, travertine stone powder (as waste in the manufacture of building materials) was used as a catalyst and waste frying oil as a source of triglyceride for biodiesel production. Using thermogravimetric and X-ray diffraction analysis, optimum temperature for catalyst calcination was selected at 900°C. Furthermore, X-ray fluorescence, Fourier transform infrared spectroscopy, Brunauer–Emmett–Teller, transmission electron microscopy and scanning electron microscopy analyses were performed. Using the design of experiments Response Surface Methodology, the optimum reaction conditions for biodiesel production yield of 97.74% were: reaction temperature 59.52°C (~60°C), time 3.8 h (228 min), catalyst concentration 1.36 wt.% and the methanol to oil molar ratio of 11:6. After reusing four times, the catalyst efficiency was reduced a little, and the biodiesel yield was 89.84%, indicating high strength and stability of the catalyst.

Natural Hydroxyapatite (NHAp) Derived from Pork Bone as a Renewable Catalyst for Biodiesel Production via Microwave Irradiation

2015 ◽  
Vol 659 ◽  
pp. 216-220 ◽  
Author(s):  
Achanai Buasri ◽  
Thaweethong Inkaew ◽  
Laorrut Kodephun ◽  
Wipada Yenying ◽  
Vorrada Loryuenyong
Keyword(s):  
Reaction Time ◽  
Microwave Power ◽  
Raw Materials ◽  
Raw Material ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Catalyst Loading ◽  
X Ray ◽  
Animal Bone ◽  
Natural Hydroxyapatite

The use of waste materials for producing biodiesel via transesterification has been of recent interest. In this study, the pork bone was used as the raw materials for natural hydroxyapatite (NHAp) catalyst. The calcination of animal bone was conducted at 900 °C for 2 h. The raw material and the resulting heterogeneous catalyst were characterized using X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM) and the Brunauer-Emmett-Teller (BET) method. The effects of reaction time, microwave power, methanol/oil molar ratio, catalyst loading and reusability of catalyst were systematically investigated. The optimum conditions, which yielded a conversion of oil of nearly 94%, were reaction time 5 min and microwave power 800 W. The results indicated that the NHAp catalysts derived from pork bone showed good reusability and had high potential to be used as biodiesel production catalysts under microwave-assisted transesterification of Jatropha Curcas oil with methanol.

scholarly journals Effects of different Sn contents on formation of Ti2SnC by self-propagating high-temperature synthesis method in Ti-Sn-C and Ti-Sn-C-TiC systems

2014 ◽  
Vol 32 (4) ◽  
pp. 696-701 ◽  
Author(s):  
Hong-Yan Sun ◽  
Xin Kong ◽  
Wei Sen ◽  
Zhong-Zhou Yi ◽  
Bao-Sen Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Raw Materials ◽  
Synthesis Method ◽  
Combustion Products ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Temperature Synthesis ◽  
X Ray ◽  
High Temperature Synthesis ◽  
Scanning Electron

AbstractEffect of different Sn contents on combustion synthesis of Ti2SnC was studied using elemental Ti, Sn, C and TiC powders as raw materials in the Ti-Sn-C and Ti-Sn-C-TiC system, in which the molar ratio of Ti/C was set as 2:1. The reaction mechanism for the formation of Ti2SnC was also investigated. The results showed that the amount of Ti2SnC in combustion products firstly increased with increasing of Sn content (0.6 to 0.8 mol), and then decreased with further increasing of Sn content (1.0 to 1.2 mol). Upon addition of 15 % TiC instead of Ti and C, the optimum addition of Sn decreased to 0.7 mol and a higher purity of Ti2SnC was obtained. The Ti2SnC powders were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD).

CuS Nanotubes:Microwave-Solvothermal Synthesis and Photocatalytic Property

2012 ◽  
Vol 554-556 ◽  
pp. 605-609 ◽  
Author(s):  
Xiao Lin Liu ◽  
Ying Jie Zhu ◽  
Bin Yang ◽  
Qian Zhang ◽  
Zhi Feng Li
Keyword(s):  
Electron Microscopy ◽  
Copper Sulfide ◽  
Solvothermal Synthesis ◽  
Solvothermal Method ◽  
Raw Materials ◽  
Low Cost ◽  
Photocatalytic Property ◽  
X Ray ◽  
Microwave Assisted ◽  
Transmission Electron

Copper sulfide (CuS) nanotubes assembled by nanoparticles were successfully synthesized by reaction thiourea with Cu(OH)2nanowire precursor which was obtained using CuCl2and NaOH as raw materials in the solvent ethylene glycol at 80 °C by a facile microwave-assisted solvothermal method. The forming influencing factors of CuS nanotubes were investigated. One of the advantages of this method is that the preparation of CuS nanotubes can well duplicate the shape of the nanowire precursor, thus the simplicity and low cost can be achieved. The products are characterized by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The photocatalytic property of the CuS samples was also investigated.

scholarly journals Synthesis of an optical catalyst for cracking contaminating dyes in the wastewater of factories using indium oxide in nanometer and usage in agriculture

2019 ◽  
Vol 21 (4) ◽  
pp. 98-105 ◽  
Author(s):  
Ishaq F. E. Ahmed ◽  
Ahmed I. El-Shenawy ◽  
Moamen S. Refat
Keyword(s):  
Electron Microscopy ◽  
Indium Oxide ◽  
Organic Dyes ◽  
Low Cost ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Ft Ir ◽  
20 Nm

Abstract Herein, the photocatalytic degradation of the Congo Red (CR) and Crystal Violet (CV) dyes in an aqueous solution were discussed in the presence of an indium(III) oxide (In2O3) as optical catalyst efficiency. The caproate bidentate indium(III) precursor complex has been synthesized and well interpreted by elemental analysis, molar conductivity, Fourier transform infrared (FT-IR), UV-Vis, and thermogravimetric (TGA) with its differential thermogravimetric (DTG) studies. The microanalytical and spectroscopic assignments suggested that the associated of mononuclear complex with 1:3 molar ratio (M3+:ligand). Octahedral structure is speculated for this parent complex of the caproate anion, CH3(CH2)4COO− ligand. The In2O3 NPs with nanoscale range within 10–20 nm was synthesized by a simple, low cost and eco-friendly method using indium(III) caproate complex. Indium oxide nanoparticles were formed after calcination of precursor in static air at 600°C for 3 hrs. The structural, grain size, morphological and decolorization efficiency of the synthesized NPs were characterized using the FT-IR, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and transmission electron microscopy (TEM) analyses. It was worthy mentioned that the prepared In2O3 NPs showed a good photodegradation properties against CR and CV organic dyes during 90 min.

Bamboo Waste-based Bio-composite Substance: An application for Low-cost Construction Materials

2020 ◽  
Vol 4 (1) ◽  
pp. 41-48
Author(s):  
Teodoro Astorga Amatosa ◽  
Michael E. Loretero
Keyword(s):  
Composite Materials ◽  
Sea Water ◽  
Raw Materials ◽  
Low Cost ◽  
Construction Materials ◽  
Single Layer ◽  
High Strength ◽  
Green Technology ◽  
Experimental Medium ◽  
Natural Treatment

Bamboo is a lightweight and high-strength raw materials that encouraged researchers to investigate and explore, especially in the field of biocomposite and declared as one of the green-technology on the environment as fully accountable as eco-products. This research was to assess the technical feasibility of making single-layer experimental Medium-Density Particleboard panels from the bamboo waste of a three-year-old (Dendrocalamus asper). Waste materials were performed to produce composite materials using epoxy resin (C21H25C105) from a natural treatment by soaking with an average of pH 7.6 level of sea-water. Three different types of MDP produced, i.e., bamboo waste strip MDP (SMDP), bamboo waste chips MDP (CMDP) and bamboo waste mixed strip-chips MDP (MMDP) by following the same process. The experimental panels tested for their physical-mechanical properties according to the procedures defined by ASTM D1037-12. Conclusively, even the present study shows properties of MDP with higher and comparable to other composite materials; further research must be given better attention as potential substitute to be used as hardwood materials, especially in the production, design, and construction usage.

Calcium Methoxide Synthesis from Quick Lime Using as Solid Catalyst in Refined Palm Oil Biodiesel Production

2013 ◽  
Vol 834-836 ◽  
pp. 550-554 ◽  
Author(s):  
Warakom Suwanthai ◽  
Vittaya Punsuvon ◽  
Pilanee Vaithanomsat
Keyword(s):  
Palm Oil ◽  
Acid Methyl Ester ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Catalyst Loading ◽  
Solid Catalyst ◽  
Solid Base ◽  
Quick Lime ◽  
X Ray ◽  
Refined Palm Oil

In this research, calcium methoxide was synthesized as solid base catalyst from quick lime for biodiesel production. The catalyst was further characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), attenuated total reflection fourier transform (ATR-FTIR) and Energy-dispersive X-ray spectroscopies (EDX) to evaluate its performance. The transesterification of refined palm oil using calcium methoxide and the process parameters affecting the fatty acid methyl ester (FAME) content such as catalyst concentration, methanol:oil molar ratio and reaction time were investigated. The results showed that the FAME content at 97% was achieved within 3 h using 3 %wt catalyst loading, 12:1 methanol:oil molar ratio and 65 °C reaction temperature. The result of FAME suggested calcium methoxide was the promising solid catalyst for substitution of the conventional liquid catalyst.

scholarly journals Design of Low-Cost and High-Strength Titanium Alloys Using Pseudo-Spinodal Mechanism through Diffusion Couple Technology and CALPHAD

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2910
Author(s):  
Chaoyi Ding ◽  
Chun Liu ◽  
Ligang Zhang ◽  
Di Wu ◽  
Libin Liu
Keyword(s):  
Diffusion Couple ◽  
Titanium Alloys ◽  
High Throughput ◽  
Volume Fraction ◽  
Raw Materials ◽  
Low Cost ◽  
High Strength ◽  
High Yield ◽  
Α Phase ◽  
Cr System

The high cost of development and raw materials have been obstacles to the widespread use of titanium alloys. In the present study, the high-throughput experimental method of diffusion couple combined with CALPHAD calculation was used to design and prepare the low-cost and high-strength Ti-Al-Cr system titanium alloy. The results showed that ultra-fine α phase was obtained in Ti-6Al-10.9Cr alloy designed through the pseudo-spinodal mechanism, and it has a high yield strength of 1437 ± 7 MPa. Furthermore, application of the 3D strength model of Ti-6Al-xCr alloy showed that the strength of the alloy depended on the volume fraction and thickness of the α phase. The large number of α/β interfaces produced by ultra-fine α phase greatly improved the strength of the alloy but limited its ductility. Thus, we have demonstrated that the pseudo-spinodal mechanism combined with high-throughput diffusion couple technology and CALPHAD was an efficient method to design low-cost and high-strength titanium alloys.

Application of vermiculite and limestone to desulphurization and to the removal of dust during briquette combustion

2003 ◽  
Vol 67 (6) ◽  
pp. 1243-1251 ◽  
Author(s):  
A. Lu ◽  
D. Zhao ◽  
J. Li ◽  
C. Wang ◽  
S. Qin
Keyword(s):  
Electron Microscopy ◽  
Coal Combustion ◽  
Combustion Temperature ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Retention Ratio ◽  
X Ray ◽  
Major Factors ◽  
Chemical Reactant ◽  
Scanning Electron

AbstractSmall domestic cooking furnaces are widely used in China. These cooking furnaces release SO2 gas and dust into the atmosphere and cause serious air pollution. Experiments were conducted to investigate the effects of vermiculite, limestone or CaCO3, and combustion temperature and time on desulphurization and dust removal during briquette combustion in small domestic cooking furnaces. Additives used in the coal are vermiculite, CaCO3 and bentonite. Vermiculite is used for its expansion property to improve the contact between CaCO3 and SO2 and to convey O2 into the interior of briquette; CaCO3 is used as a chemical reactant to react with SO2 to form CaSO4; and bentonite is used to develop briquette strength. Expansion of vermiculite develops loose interior structures, such as pores or cracks, inside the briquette, and thus brings enough oxygen for combustion and sulphation reaction. Effective combustion of the original carbon reduces amounts of dust in the fly ash. X-ray diffraction, optical microscopy, and scanning electron microscopy with energy dispersive X-ray analysis show that S exists in the ash only as anhydrite CaSO4, a product of SO2 reacting with CaCO3 and O2. The formation of CaSO4 effectively reduces or eliminates SO2 emission from coal combustion. The major factors controlling S retention are vermiculite, CaCO3 and combustion temperature. The S retention ratio increases with increasing vermiculite amount at 950°C. The S retention ratio also increases with increasing Ca/S molar ratio, and the best Ca/S ratio is 2-3 for most combustion. With 12 g of the original coal, 1 to 2 g of vermiculite, a molar Ca/S ratio of 2.55 by adding CaCO3, and some bentonite, a S retention ratio >65% can be readily achieved. The highest S retention ratio of 97.9% is achieved at 950°C with addition of 2 g of vermiculite, a Ca/S ratio of 2.55 and bentonite.

Influence of Fly Ash on Corrosion Resistance of Refractory Forsterite-Spinel Ceramics

2021 ◽  
Vol 325 ◽  
pp. 181-187
Author(s):  
Martin Nguyen ◽  
Radomír Sokolář
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Corrosion Resistance ◽  
Fly Ash ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transition Zones ◽  
Refractory Ceramics ◽  
Scanning Electron

This article examines the influence of fly ash on corrosion resistance of refractory forsterite-spinel ceramics by molten iron as a corrosive medium. Fly ash in comparison with alumina were used as raw materials and sources of aluminium oxide for synthesis of forsterite-spinel refractory ceramics. Raw materials were milled, mixed in different ratios into two sets of mixtures and sintered at 1550°C for 2 hours. Samples were characterized by X-ray diffraction analysis and thermal dilatometric analysis. Crucibles were then made from the fired ceramic mixtures and fired together with iron at its melting point of 1535°C for 5 hours. The corrosion resistance was evaluated by scanning electron microscopy on the transition zones between iron and ceramics. Mixtures with increased amount of spinel had higher corrosion resistance and mixtures with fly ash were comparable to mixtures with alumina in terms of corrosion resistance and refractory properties.

Preparation and Characterization of Nanocomposite Calcium Doped Ceria Electrolyte With Alkali Carbonates (NK-CDC) for SOFC

2010 ◽  
Author(s):  
Ghazanfar Abbas ◽  
Rizwan Raza ◽  
Muhammad Ashraf Chaudhry ◽  
Bin Zhu
Keyword(s):  
Electron Microscopy ◽  
Fossil Fuels ◽  
Electrochemical Impedance ◽  
Renewable Energy Sources ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Doped Ceria ◽  
Alternative Source ◽  
Calcium Doped ◽  
Co Precipitation

The entire world’s challenge is to find out the renewable energy sources due to rapid depletion of fossil fuels because of their high consumption. Solid Oxide Fuel Cells (SOFCs) are believed to be the best alternative source which converts chemical energy into electricity without combustion. Nanostructured study is required to develop highly ionic conductive electrolyte for SOFCs. In this work, the calcium doped ceria (Ce0.8Ca0.2O1.9) coated with 20% molar ratio of two alkali carbonates (CDC-M: MCO3, where M = Na and K) electrolyte was prepared by co-precipitation method in this study. Ni based electrode was used to fabricate the cell by dry pressing technique. The crystal structure and surface morphology was characterized by X-Ray Diffractometer (XRD), Scanning Electron Microscopy (SEM) and High Resolution Transmission Electron Microscopy (HRTEM). The particle size was calculated in the range of 10–20nm by Scherrer’s formula and compared with SEM and TEM results. The ionic conductivity was measured by using AC Electrochemical Impedance Spectroscopy (EIS) method. The activation energy was also evaluated. The performance of the cell was measured 0.567W/cm2 at temperature 550°C with hydrogen as a fuel.

Sign in / Sign up

Export Citation Format

Share Document