Sealing performance and fatigue life of the fracturing packer rubber of various materials

2019 ◽  
Vol 233 (17) ◽  
pp. 6157-6166 ◽  
Author(s):  
Fuying Zhang ◽  
Haoche Shui ◽  
Jun-Mei Yang
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Contact Stress ◽  
Field Experiments ◽  
Structural Parameters ◽  
Element Model ◽  
Rubber Seal ◽  
Maximum Contact Stress ◽  
Different Temperatures ◽  
Maximum Contact

The finite element model of four packer rubber materials was established by using ABAQUS and FE-SAFE software. The initial sealing load (the load is the pressure) was 11.85 MPa, and the working load was 58.15 MPa. The sealing evaluation coefficient, maximum contact stress, and fatigue life value of four material packer rubbers were considered when considering temperature changes and fatigue unit nodes. The results show that when the working load and the structural parameters of the rubber are the same, the sealing evaluation coefficient of the four material rubber increases with the increase of temperature. When the working temperature reaches 125 ℃, the value of the rubber seal evaluation coefficient of the HNBR material is the largest, and the value of the rubber seal evaluation coefficient of the EPDM material is the smallest. Similarly, the maximum contact stress of the four material rubbers increases with increasing temperature. When the temperature reaches 125 ℃, the maximum contact stress of the HNBR material is the largest, and the maximum contact stress of the EPDM material is the smallest. The rubber of the four materials increase the fatigue life value with the increase in the temperature within the operating temperature range studied. When the temperature is lower than 120 ℃, the fatigue life value of the HNBR material rubber is the largest. When the temperature is higher than 120 ℃, the fatigue life value of the CR material rubber is the largest. Regardless of the temperature change, the fatigue life value of the EPDM is the smallest. By comparing the results of field experiments with the results of finite element models, the two are found to have good consistency, which verifies the validity and feasibility of the model. The research results have important guiding significance for the fatigue life prediction of various material packer rubbers under different temperatures.

Computational Analysis of Stress Field and Contact Pressure for Rubber Seal Based on Non-Linear Finite Element

2012 ◽  
Vol 268-270 ◽  
pp. 1080-1083 ◽  
Author(s):  
Jian Bing Sang ◽  
Li Fang Sun ◽  
Su Fang Xing ◽  
Dong Ling Zhang
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Stress Field ◽  
Contact Stress ◽  
Von Mises Stress ◽  
Rubber Seal ◽  
Linear Finite Element ◽  
Maximum Contact Stress ◽  
Von Mises ◽  
Maximum Contact

This paper aims to research on the sealing capability of rubber seal by utlizing non-linear finite element analysis. After discussion on various types of strain energy functions of rubber like materials, material parameters of Mooney-Rivilin model are determined by curve fitting based on the stress strain curve from the uniaxial tensile experiment. Axis symmetric and isotropic finite element model is developed to analyze the stress field and contact pressue of O-ring seal and lip seal at different medium pressure. Von-mises stress distribution rule and contact stress distribution curve on contact surface are achieved. The results show that maximum Von Mises stress increase with the increases of oil pressure. The maximum contact stress appears on the middle contact zone and the maximum contact stress and contact width increases obviously with the increases of oil pressure. In the meanwhile, the maximum contact stress is greater than midum pressure which can prevent the leakage of midum and achieve the function of sealing. The research results will be a useful technique for predicting the properties of rubber seal and providing reference for engineering design.

Finite Element Analysis for Gear Contact Based on UG and ABAQUS

2013 ◽  
Vol 442 ◽  
pp. 229-232 ◽  
Author(s):  
Li Mei Wu ◽  
Fei Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Contact Stress ◽  
Three Dimensional ◽  
Element Model ◽  
Tooth Surface ◽  
Element Analysis ◽  
Tooth Width ◽  
Gear Contact ◽  
Maximum Contact

According to the cutting theory of involute tooth profile, established an exact three-dimensional parametric model by UG. Used ABAQUS to crate finite element model for gear meshing. After simulated the meshing process, discussed the periodicity of the tooth surface contact stress. Based on the result of finite element analysis, made a comparison of the maximum contact stress between finite element solution and Hertz theoretical solution, analyzed the contact stress distribution on tooth width, and researched the effect of friction factor on contact stress. All that provided some theoretical basis for gear contact strength design.

Instantaneous Dynamic Analysis of the New Stirring Kneader Shaft

2011 ◽  
Vol 221 ◽  
pp. 472-477
Author(s):  
Zhi Min Fan ◽  
Guang Ting Zhou ◽  
Jian Ping Liu
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Dynamic Response ◽  
Finite Element Model ◽  
Dynamic Analysis ◽  
Structural Parameters ◽  
Element Model ◽  
Fatigue Analysis ◽  
Exciting Force ◽  
The Finite Element Model

The finite element model of the stirring kneader shaft was built by PRO/E software, which was inserted into ANSYS. Next, the instantaneous dynamic analysis of the new stirring kneader shaft was carried out. The instantaneous dynamic response of stirring shaft about the exciting force of fluid was obtained, which was to optimize the structural parameters of the stirring shaft. The foundation for the next fatigue analysis was laid based on the instantaneous dynamic response; the fatigue life of stirring kneader shaft can be predicted.

Validation of a Finite Element Humeroradial Joint Model of Contact Pressure Using Fuji Pressure Sensitive Film

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Sunghwan Kim ◽  
Mark Carl Miller
Keyword(s):  
Finite Element ◽  
Contact Stress ◽  
Contact Area ◽  
Axial Loads ◽  
Contact Areas ◽  
Pressure Sensitive ◽  
Maximum Contact Stress ◽  
Sensitive Film ◽  
Pressure Sensitive Film ◽  
Maximum Contact

A finite element (FE) elbow model was developed to predict the contact stress and contact area of the native humeroradial joint. The model was validated using Fuji pressure sensitive film with cadaveric elbows for which axial loads of 50, 100, and 200 N were applied through the radial head. Maximum contact stresses ranged from 1.7 to 4.32 MPa by FE predictions and from 1.34 to 3.84 MPa by pressure sensitive film measurement while contact areas extended from 39.33 to 77.86 mm2 and 29.73 to 83.34 mm2 by FE prediction and experimental measurement, respectively. Measurements from cadaveric testing and FE predictions showed the same patterns in both the maximum contact stress and contact area, as another demonstration of agreement. While measured contact pressures and contact areas validated the FE predictions, computed maximum stresses and contact area tended to overestimate the maximum contact stress and contact area.

The Effects of Load on the Radial Bearing Properties of Pre-Loaded Cylindrical Roller Bearings

2011 ◽  
Vol 130-134 ◽  
pp. 2306-2310
Author(s):  
Yan Gang Wei ◽  
Meng Sun
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Contact Stress ◽  
Radial Load ◽  
The Finite Element Method ◽  
Roller Bearings ◽  
Radial Stiffness ◽  
Maximum Contact Stress ◽  
Maximum Contact ◽  
Cylindrical Roller

According to the theory of contact mechanics, the radial stiffness, the maximum contact stress, and the maximum radial load of pre-loaded cylindrical roller bearings, including both solid roller and hollow roller bearings, are calculated with the finite element method. The effects of load on the radial stiffness, the maximum contact stress, and the maximum radial load of bearing are analyzed. The analysis results show that the effect of load on the radial stiffness is complex. Under the different magnitude loads, the effects of both hollowness and interference magnitude on the radial stiffness and on the maximum contact stress are not same. Thus the effects of load magnitude must be considered in the design and application of pre-loaded cylindrical roller bearings.

Improvement and Taper Optimal Design of the Hydraulic Fast Connector

2013 ◽  
Vol 341-342 ◽  
pp. 406-410
Author(s):  
Heng Fu Xiang
Keyword(s):  
Finite Element ◽  
Optimal Design ◽  
Contact Stress ◽  
Contact Surface ◽  
Maximum Contact Stress ◽  
Finite Element Technology ◽  
Simulation Results ◽  
The Relationship ◽  
Maximum Contact

Improvement design was carried out to resolve the issue about easily damaged and difficult repaired planar seal for hydraulic fast connector. Through adding a taper on male connector and female regulating part on female connector, the co-planar seal was changed into the taper seal which the seal was more reliable. When the contact surface was worn, it can be resealed by adjusting the female regulating part. Taper seal was key to design the reasonable taper. In order to acquire the best taper, taper optimal design was carried out using finite element technology, the relationship between maximum contact stress and tape was gained. Simulation results showed that the best taper could be gained when the big-endian radius of the taper was 11.82 mm.

Nonlinear Analysis of Rotary Sealing Performance of Rubber O-Ring

2013 ◽  
Vol 470 ◽  
pp. 371-375 ◽  
Author(s):  
Shao Hua Chen ◽  
Guo Zhang Jiang ◽  
Gong Fa Li ◽  
Liang Xi Xie ◽  
Wen Qiang Qian
Keyword(s):  
Contact Stress ◽  
Element Model ◽  
Rotating Shaft ◽  
Medium Pressure ◽  
Maximum Contact Stress ◽  
Sealing Performance ◽  
Two Factors ◽  
Ring Seal ◽  
Von Mises ◽  
Maximum Contact

The two-dimensional O-ring seal nonlinear axisymmetric finite element model are established which is used for swinging hydraulic cylinder. Some factors influencing rubber O-ring sealing performance were taken into account, such as rotating shaft diameter, O-ring seal section diameter. The results indicate that when medium pressure is zero, the two factors influence Von Mises and maximum contact stress of sealing face greatly. Under medium pressure (P=10Mpa), the two factors have a little influence to Von Mises and maximum contact stress.

Rolling Resistance Calculation Procedure Using the Finite Element Method

2019 ◽  
Vol 48 (3) ◽  
pp. 224-248
Author(s):  
Pablo N. Zitelli ◽  
Gabriel N. Curtosi ◽  
Jorge Kuster
Keyword(s):  
Finite Element ◽  
Energy Dissipation ◽  
Rolling Resistance ◽  
Element Model ◽  
The Finite Element Method ◽  
Temperature Changes ◽  
Rubber Compounds ◽  
Different Temperatures ◽  
Materials Used ◽  
Account Temperature

ABSTRACT Tire engineers are interested in predicting rolling resistance using tools such as numerical simulation and tests. When a car is driven along, its tires are subjected to repeated deformation, leading to energy dissipation as heat. Each point of a loaded tire is deformed as the tire completes a revolution. Most energy dissipation comes from the cyclic loading of the tire, which causes the rolling resistance in addition to the friction force in the contact patch between the tire and road. Rolling resistance mainly depends on the dissipation of viscoelastic energy of the rubber materials used to manufacture the tires. To obtain a good rolling resistance, the calculation method of the tire finite element model must take into account temperature changes. It is mandatory to calibrate all of the rubber compounds of the tire at different temperatures and strain frequencies. Linear viscoelasticity is used to model the materials properties and is found to be a suitable approach to tackle energy dissipation due to hysteresis for rolling resistance calculation.

Structural Optimization of the Telescopic Boom of a Certain Type of Truck-Mounted Crane

2014 ◽  
Vol 548-549 ◽  
pp. 383-388
Author(s):  
Zhi Wei Chen ◽  
Zhe Cui ◽  
Yi Jin Fu ◽  
Wen Ping Cui ◽  
Li Juan Dong ◽  
...  
Keyword(s):  
Finite Element ◽  
Static Analysis ◽  
Cross Sections ◽  
Optimization Design ◽  
Structural Parameters ◽  
Vertical Direction ◽  
Element Model ◽  
Shape Parameters ◽  
Conventional Design ◽  
Design Variables

Parametric finite element model for a commonly used telescopic boom structure of a certain type of truck-mounted crane has been established. Static analysis of the conventional design configuration was performed first. And then an optimization process has been carried out to minimize the total weight of the telescopic structures. The design variables include the geometric shape parameters of the cross-sections and the integrated structural parameters of the telescopic boom. The constraints include the maximum allowable equivalent stresses and the flexure displacements at the tip of the assembled boom structure in both the vertical direction and the circumferential direction of the rotating plane. Compared with the conventional design, the optimization design has achieved a significant weight reduction of up to 24.3%.

Analysis of Premium Connection of Connecting and Sealing Ability Loaded by Axial Tensile Loads

2012 ◽  
Vol 268-270 ◽  
pp. 737-740
Author(s):  
Yang Yu ◽  
Yi Hua Dou ◽  
Fu Xiang Zhang ◽  
Xiang Tong Yang
Keyword(s):  
Finite Element ◽  
Contact Pressure ◽  
Tensile Load ◽  
Element Model ◽  
Sealing Ability ◽  
Axial Tensile ◽  
High Level ◽  
Maximum Contact ◽  
Contact Pressures ◽  
The Finite Element Model

It is necessary to know the connecting and sealing ability of premium connection for appropriate choices of different working conditions. By finite element method, the finite element model of premium connection is established and the stresses of seal section, shoulder zone and thread surface of tubing by axial tensile loads are analyzed. The results show that shoulder zone is subject to most axial stresses at made-up state, which will make distribution of stresses on thread reasonable. With the increase of axial tensile loads, stresses of thread on both ends increase and on seal section and shoulder zone slightly change. The maximum stress on some thread exceed the yield limit of material when axial tensile loads exceed 400KN. Limited axial tensile loads sharply influence the contact pressures on shoulder zone while slightly on seal section. Although the maximum contact pressure on shoulder zone drop to 0 when the axial tensile load is 600KN, the maximum contact pressure on seal section will keep on a high level.

Sign in / Sign up

Export Citation Format

Share Document